Parts for Ge PSDF5RGXCFCC: 03 - Freezer Section Parts

Replace worn refrigerator door foam seal strip to improve cooling efficiency and reduce energy costs. Self-adhesive installation. Verify fit with your model.

Foam seal strip creates an airtight barrier between refrigerator components. Replace when worn, compressed, or damaged to maintain efficiency. Verify fit with your model number before ordering.

Seals the plenum chamber in your refrigerator to maintain proper airflow and temperature. Replace if torn, cracked, or causing temperature issues.

Circulates cold air across the evaporator coil in your refrigerator. Replace if cracked, broken, or worn to restore proper airflow and even cooling.

Front cover panel for refrigerator evaporator assembly. Replaces cracked, broken, or missing covers. Installs over evaporator coils in freezer section.

Refrigerator evaporator cover gasket seals the evaporator compartment to maintain proper temperature and efficiency. Replace if torn or compressed.

Upper freezer tower bracket secures the ice/tower assembly inside your refrigerator's freezer. Replace if cracked, broken, or missing to restore support.

Intermediate freezer wire harness connects cabinet wiring to freezer components. Replace if wires are damaged, connections corroded, or harness broken.

Fridge warm but freezer cold? Frost buildup on evaporator coils means a failed defrost heater. This assembly prevents ice blockage, restoring airflow.

Seals the evaporator block to the freezer cabinet, maintaining proper airflow and preventing air leakage. Replace if cooling is uneven or frost builds up.

Drip trough assembly catches defrost and condensation water in your side-by-side refrigerator. Replace if cracked, broken, or causing leaks.

Fix uneven cooling or defrost issues with a new temperature sensor. Most DIYers complete this repair in under an hour with basic tools and our video.

Protective grille cover that mounts over the temperature sensor in your refrigerator. Replace if cracked, broken, or missing to properly shield the sensor.

The Temperature Sensor Seal is an OEM part for GE refrigerators. This seal is designed to protect the temperature sensor from moisture and other environmental factors that could affect its accuracy and longevity. By providing a barrier against the hars

Fix a warm fridge with cold freezer or frost buildup on coils. This defrost thermostat regulates defrost cycles. DIY repair in under 30 minutes with video.

Fix uneven cooling or defrost issues with a new temperature sensor. Most DIYers complete this repair in under an hour with basic tools and our video.

Seals the plenum chamber in your refrigerator to maintain proper airflow and temperature control. Replace if torn, compressed, or causing uneven cooling.

Self-adhesive foam strip seals gaps in your refrigerator to prevent air leaks and maintain temperature. Replace when worn, compressed, or damaged.

Protects the freezer light bulb from damage while maintaining visibility. Replace if cracked, yellowed, or broken. Confirm fit with your model number.

Bottom door hinge and pin assembly for side-by-side refrigerators. Replaces broken, worn, or damaged hinges causing door misalignment or sagging.

Bottom hinge and pin assembly secures the lower refrigerator door, enabling smooth pivoting and alignment. Replace if worn, bent, or broken to restore stability.

Black bottom door hinge and pin assembly for side-by-side refrigerators. Replace this load-bearing pivot component if cracked, broken, or worn out.

Secures mobility components and wheel brackets on side-by-side refrigerators. Replace if screw is missing, stripped, or worn to restore stable mounting.

Front caster assembly that mounts to the bottom of your refrigerator. Replace if cracked, broken, or worn to restore smooth rolling and stability.

White corner cap cover for side-by-side refrigerators. Replaces cracked, broken, or missing corner trim pieces. Restores clean appearance.

This replacement corner cap restores the finished edge and protective cover on an oven door corner for a clean appearance and proper fit. It replaces a cracked, chipped, or missing corner that can catch debris or show damage. What it does:

• Cover

Corner cap cover for side-by-side refrigerators. Replaces broken, cracked, or missing corner trim caps. Restores finished appearance to cabinet edges.

Base grille kickplate mounts across the lower front of your refrigerator, covering the condenser area. Replace if cracked, broken, or missing.

Decorative base grille panel that covers the condenser area at the bottom front of your refrigerator. Replace if cracked, broken, or missing.

The Light Socket is an OEM part for GE refrigerators. It is responsible for holding the refrigerator's light bulb and ensuring it receives power to illuminate the interior when the door is opened.

You should replace the light socket if it b

The Light Bulb (40W) is an OEM component for GE refrigerators. As an essential task lamp, it illuminates the interior of the refrigerator and freezer compartments. 

All light bulbs will eventually burn out with consistent use over many yea

Top door hinge and pin assembly for refrigerators. Installs at the upper door mount. Replace if hinge is cracked, pin is worn, or door sags or misaligns.

Replacement mounting screw for refrigerator panels, brackets, and hardware. Restores secure fit when original is missing, stripped, or corroded.

The GE Door Light Switch is an OEM Replacement Part that serves as the Freezer Door Fan and Light Switch. The switch is made from metal, wiring, and plastic. It plays an essential role in energy conservation by turning off the light when the refrigerat

Fix a warm freezer or thawing food with this evaporator fan motor. Circulates cold air over coils. DIY-friendly repair in about 30 minutes with basic tools.

Secures the lower edge of the evaporator assembly inside your refrigerator. Replace if cracked, broken, or missing to restore proper alignment.

Replace missing or stripped #8-18 x 5/8-inch Torx T20 screws in your side-by-side refrigerator. Secures panels, brackets, drawer rails, and trim.

Rattling noise or warm temps? A broken evaporator fan blade disrupts air circulation. This repair takes 30-45 minutes with basic tools and our video guide.

The Lid Bumper is an OEM part for GE refrigerators. It is designed to provide cushioning and protection for the refrigerator lid, preventing damage and ensuring smooth, quiet closing. 

Causes of a bad Lid Bumper can include deterioration o

Rubber grommet that seals and cushions where the evaporator fan motor shaft mounts. Replace if cracked, worn, or missing to eliminate noise and vibration.

Secures and seals water line connections in your refrigerator's dispensing system. Replace if leaking or loose to prevent water damage. Confirm fit.

This evaporator fan motor dust cap is an authentic OEM replacement part found on refrigerator and freezer fan motors. This dust cap prevents the fan motor bearing and housing from being damaged by dirt and debris. If the dust cap is cracked or broken, the

Replaces the freezer door lever assembly on side-by-side refrigerators. Installs on freezer door. Needed when original lever is broken or cracked.

Replaces the freezer door lever assembly on side-by-side refrigerators. Installs on freezer door. Needed when original lever is broken or cracked.

Black plastic lever assembly that installs on the freezer door hinge mechanism. Replace when cracked, broken, or missing to restore proper door closure.

Replacement door closure spring for refrigerator hinges. Installs on door hinge assembly to provide tension for proper closing. Needed when broken or worn.

Fastens refrigerator panels, brackets, and internal components. Replace this screw if the original is missing, stripped, or damaged to restore secure mounting.