Parts for Ge PSHF9PGZBCBB: 04 - Freezer Section Parts

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

Replace worn refrigerator door foam seal strip to improve cooling efficiency and reduce energy costs. Self-adhesive installation. Verify fit with your model.

Foam seal strip creates an airtight barrier between refrigerator components. Replace when worn, compressed, or damaged to maintain efficiency. Verify fit with your model number before ordering.

Refrigerator plenum gasket seals air duct between fresh food and freezer sections. Replace if torn, cracked, or causing temperature issues. Verify fit with your model number before ordering.

Freezer air duct plenum extension that clips into the duct opening to direct airflow. Replace if cracked, broken, or missing to restore proper air circulation.

Seals evaporator cover to cabinet, preventing air leaks and frost buildup. Replace if worn or cracked to restore proper airflow and temperature control.

Replacement wire harness that connects freezer compartment AC components. Needed when original wiring is damaged, corroded, or has loose connectors.

Fridge warm but freezer cold? Frost buildup on evaporator coils means a failed defrost heater. This assembly prevents ice blockage, restoring airflow.

Seals the evaporator block to the freezer cabinet, maintaining proper airflow and preventing air leakage. Replace if cooling is uneven or frost builds up.

Drip trough assembly catches defrost and condensation water in your side-by-side refrigerator. Replace if cracked, broken, or causing leaks.

Protective grille cover that mounts over the temperature sensor in your refrigerator. Replace if cracked, broken, or missing to properly shield the sensor.

Fix inconsistent temps or ice buildup on evaporator coils? This sensor seal protects accuracy. DIY-friendly with wire splicing. Video guide available.

Freezer coils icing up and fridge too warm? This defrost thermostat monitors evaporator temperature to prevent overheating. Easy 20-minute DIY fix.

Fix uneven cooling or defrost issues with a new temperature sensor. Most DIYers complete this repair in under an hour with basic tools and our video.

If your refrigerator isn't cooling properly or makes unusual noises, the evaporator fan assembly may need replacement. Moderate DIY repair for side-by-side models.

Replace your refrigerator plenum gasket to restore proper airflow and temperature control. Install when torn, compressed, or causing air leaks. Verify fit with your model number.

Self-adhesive foam strip seals gaps in your refrigerator to prevent air leaks and maintain temperature. Replace when worn, compressed, or damaged.

Directs airflow inside your refrigerator for proper venting and component fit. Replace if cracked, warped, or broken to restore internal alignment.

Plenum shield insert for refrigerator air distribution system. Replaces cracked, broken, or missing inserts that affect airflow routing. Direct fit part.

Bottom door hinge and pin assembly for side-by-side refrigerators. Replace this structural part if cracked, broken, or worn to restore door support.

Secures mobility components and wheel brackets on side-by-side refrigerators. Replace if screw is missing, stripped, or worn to restore stable mounting.

Front caster assembly that mounts to the bottom of your refrigerator. Replace if cracked, broken, or worn to restore smooth rolling and stability.

Replacement corner cap for refrigerator door edges. Covers and protects the outer corner from damage. Replaces cracked, chipped, or missing caps.

White corner cap cover for side-by-side refrigerators. Replaces cracked, broken, or missing corner trim pieces. Restores clean appearance.

Base grille kickplate mounts across the lower front of your refrigerator, covering the condenser area. Replace if cracked, broken, or missing.

Decorative base grille panel that covers the condenser area at the bottom front of your refrigerator. Replace if cracked, broken, or missing.

White plastic hinge cover for refrigerator freezer door. Replaces cracked, broken, or missing covers. Snaps onto hinge assembly for a clean finish.

Black plastic cover that conceals the upper hinge bracket on refrigerator doors. Replace this trim piece if cracked, broken, or missing for a clean look.

Top hinge and pin assembly for refrigerator freezer doors. Mounts at the top of the door to allow smooth opening and closing. Replace if cracked or worn.

Hex head screw for refrigerator panels, brackets, and assemblies. Replaces missing, stripped, or rusted fasteners to secure components properly.

Fixes freezer or fridge light staying on, or ice dispenser not working when door closes. Simple 5-minute DIY fix with putty knife—video included.

Fix uneven cooling or warm spots in your fridge with this evaporator fan motor. Restores airflow across coils when the fan runs weak, noisy, or stops.

Secures the lower edge of the evaporator assembly inside your refrigerator. Replace if cracked, broken, or missing to restore proper alignment.

Replace missing or stripped #8-18 x 5/8-inch Torx T20 screws in your side-by-side refrigerator. Secures panels, brackets, drawer rails, and trim.

Rattling noise or warm temps? A broken evaporator fan blade disrupts air circulation. This repair takes 30-45 minutes with basic tools and our video guide.

Rubber bumper that cushions and mounts the evaporator fan motor assembly. Replace if cracked, deteriorated, or missing to reduce vibration and noise.

Rubber grommet that seals and cushions where the evaporator fan motor shaft mounts. Replace if cracked, worn, or missing to eliminate noise and vibration.

Secures and seals water line connections in your refrigerator's dispensing system. Replace if leaking or loose to prevent water damage. Confirm fit.

Protective cap that covers the evaporator fan motor bearing and housing in freezers and refrigerators. Replace if cracked, broken, or missing to prevent debris.

Replaces the freezer door lever assembly on side-by-side refrigerators. Installs on freezer door. Needed when original lever is broken or cracked.

Black plastic lever assembly that installs on the freezer door hinge mechanism. Replace when cracked, broken, or missing to restore proper door closure.

Replacement door closure spring for refrigerator hinges. Installs on door hinge assembly to provide tension for proper closing. Needed when broken or worn.

Fastens refrigerator panels, brackets, and internal components. Replace this screw if the original is missing, stripped, or damaged to restore secure mounting.