Parts for Ge GTK18ICDLRBS: Freezer Section Parts

Mounting bracket that secures shelves and internal components in your refrigerator. Replace if cracked, broken, or missing to keep shelves stable and prevent shifting.

Replace a cracked, rusting, or missing freezer shelf to restore stable storage space. This assembly installs in the freezer compartment for organized food storage.

Plastic extension tube that connects the water valve to your ice maker. Replace if cracked, broken, or missing to restore proper water flow path.

Ice overflowing freezer or ice maker won't shut off? Replace the missing or broken ice bucket. Installs in minutes, no tools required.

Fix a refrigerator that's not cooling properly with a new evaporator fan motor. This part circulates cold air throughout the fridge compartments.

Secures the condenser fan motor in position. Replace this bracket if cracked, bent, or causing excessive vibration to restore stable mounting.

Freezer fan loud or not spinning? This evaporator fan blade circulates cold air over the coils. DIY-friendly repair with our video guide.

The Lid Bumper is an OEM part for GE refrigerators. It is designed to provide cushioning and protection for the refrigerator lid, preventing damage and ensuring smooth, quiet closing. 

Causes of a bad Lid Bumper can include deterioration over time due to frequent use, exposure to temperature variations, or damage from accidental impacts. A worn or damaged bumper may no longer provide adequate cushioning, leading to potential damage to the lid or the refrigerator itself.

Symptoms of a bad Lid Bumper include:

• The refrigerator lid closing too hard
• Unusual noises when closing the lid
• Visible wear or cracks on the bumper

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Rubber grommet that seals and cushions where the evaporator fan motor shaft mounts. Replace if cracked, worn, or missing to eliminate noise and vibration.

Fix freezer ice buildup and warm fridge temps with this defrost heater. Melts frost from evaporator coils during defrost cycles. Moderate DIY repair.

This replacement defrost heater warms the freezer's evaporator area during the automatic defrost cycle. It melts accumulated frost so air can circulate, helping maintain stable temperatures and preventing ice buildup on the back wall.

• Heats the evaporator to clear frost and ice during defrost
• Helps keep airflow passages and the defrost drain path open
• Common symptoms of a failed heater: heavy frost on the back panel/coils, poor cooling or warm sections, fan noise from ice contact, cooling returns temporarily after a manual defrost
• Typically located behind the rear freezer panel

• Disconnect power before servicing; wear cut-resistant gloves
• Access the evaporator by removing the freezer's rear panel; thaw heavy ice before removal
• Transfer any clips/brackets and route wires exactly as original, keeping them away from plastic parts
• After installation, ensure wiring connections are secure and the heater is not contacting plastic surfaces

Fix excessive ice buildup in freezer and frozen food in fresh food section. This defrost thermostat senses temperature to control defrost cycles. Easy DIY fix.

Fixes uneven cooling or frost buildup caused by a misaligned defrost heater. This holder assembly secures the element in place. 15-minute repair.

Drain trough that channels defrost water to the drain pan in your top-mount refrigerator. Replace if cracked, warped, or missing to prevent leaks.

Replaces a cracked or broken freezer tower bottom cover that mounts beneath the evaporator assembly. Directs airflow and protects internal components.

Secures and seals water line connections in your refrigerator's dispensing system. Replace if leaking or loose to prevent water damage. Confirm fit.

Hex washer head screw for refrigerator assembly. Secures internal components like fan housings and panels. Replace if stripped, missing, or damaged.

Secures brackets, panels, and internal components in your refrigerator. Replace missing or damaged screws to eliminate rattles and keep parts aligned.

Fix ice maker overfilling, leaking water lines, or no ice production. This water inlet valve assembly controls water flow to your ice maker and dispenser.

Secures trim and panels in your refrigerator. Replace when broken clips cause loose parts or rattling. Verify fit with your model number.

Secures refrigerator wiring to prevent chafing and vibration noise. Replace when damaged or missing to keep harnesses organized. Confirm fit by model.

Plastic water tube that routes water between refrigerator components like the inlet valve, dispenser, and ice maker. Replace if cracked, brittle, or leaking.

Secures water lines and wiring inside your refrigerator to prevent vibration, rubbing damage, and leaks. Replace if broken or missing. Confirm fit.

Ice maker not producing ice or stopped working? This ice maker kit restores ice production. Includes full assembly for harvesting and ejecting ice.