Parts for Ge GZS22DGJNFBB: Freezer Section Parts

Freezer air duct plenum extension that clips into the duct opening to direct airflow. Replace if cracked, broken, or missing to restore proper air circulation.

Evaporator front cover for side-by-side refrigerators. Installs over the evaporator coils in the freezer compartment. Replace if cracked or broken.

Seals evaporator cover to cabinet, preventing air leaks and frost buildup. Replace if worn or cracked to restore proper airflow and temperature control.

Freezer wire harness for side-by-side refrigerators. Connects freezer components to the control system. Replace if wires are damaged or frayed.

Fridge warm but freezer cold? Frost buildup on evaporator coils means a failed defrost heater. This assembly prevents ice blockage, restoring airflow.

Drip trough assembly catches defrost and condensation water in your side-by-side refrigerator. Replace if cracked, broken, or causing leaks.

Fix uneven cooling or defrost issues with a new temperature sensor. Most DIYers complete this repair in under an hour with basic tools and our video.

Protective grille cover that mounts over the temperature sensor in your refrigerator. Replace if cracked, broken, or missing to properly shield the sensor.

The Temperature Sensor Seal is an OEM part for GE refrigerators. This seal is designed to protect the temperature sensor from moisture and other environmental factors that could affect its accuracy and longevity. By providing a barrier against the harsh conditions within a refrigerator, such as humidity and temperature fluctuations, this seal ensures that the sensor can accurately monitor and control the refrigerator's internal temperature.

Causes of a malfunctioning Temperature Sensor Seal can include wear and tear over time, degrading the seal's effectiveness. Physical damage like tears or punctures can allow moisture to reach the sensor. Improper installation may leave gaps or loose areas around the sensor, compromising the seal.

Symptoms of a bad Temperature Sensor Seal include:

• Inaccurate temperature readings.
• Condensation or frost near the sensor location.
• Frequent cycling or unusual patterns in the refrigerator's cooling process.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Fix a warm fridge with cold freezer or frost buildup on coils. This defrost thermostat regulates defrost cycles. DIY repair in under 30 minutes with video.

Fix uneven cooling or defrost issues with a new temperature sensor. Most DIYers complete this repair in under an hour with basic tools and our video.

Protects the freezer light bulb from damage while maintaining visibility. Replace if cracked, yellowed, or broken. Confirm fit with your model number.

Black bottom door hinge and pin assembly for side-by-side refrigerators. Replace this load-bearing pivot component if cracked, broken, or worn out.

Secures mobility components and wheel brackets on side-by-side refrigerators. Replace if screw is missing, stripped, or worn to restore stable mounting.

Front caster assembly that mounts to the bottom of your refrigerator. Replace if cracked, broken, or worn to restore smooth rolling and stability.

Corner cap for side-by-side refrigerators. Covers and protects exposed corners on cabinet exterior. Replace if cracked, broken, or missing.

Decorative base grille panel that covers the condenser area at the bottom front of your refrigerator. Replace if cracked, broken, or missing.

Secures the interior LED light board in your refrigerator. Replace if cracked or missing to restore proper support and keep compartment lighting stable. Verify fit with your model number before ordering.

LED light board assembly illuminates refrigerator interior. Replace when lights dim, flicker, or fail. Verify fit using your model number for compatibility.

Black hinge cover for side-by-side refrigerator doors. Replace if cracked, broken, or missing to restore proper hinge appearance and protection.

Upper hinge pivot pin for side-by-side refrigerator freezer doors. Replace if bent, worn, or missing to restore proper door alignment and swing.

Hex head screw for refrigerator panels, brackets, and assemblies. Replaces missing, stripped, or rusted fasteners to secure components properly.

The Switch Light is an OEM component for GE side-by-side refrigerators. Integrated with the fresh food door control panel, it illuminates buttons for easy nighttime access. Reliable operation depends on functional interior lighting. 

Symptoms of a faulty switch light include:

• Intermittent or no illumination from the button area when the door opens  
• Dim or uneven visibility reducing button recognition in low light 
• Potential shorts if moisture penetrates cracked lens housing

Causes involve typical wear of plastic enclosure/wiring over extended duty cycles, repeated door openings straining connection points, or condensed moisture within compact spaces.  

Replacing with this genuine GE switch light ensures optimized visibility for late-night adjustments through precisely fitted components. Compatible replacements suit Hotpoint, RCA, or Kenmore refrigerator units seeking enduring, dependable interface lighting performance.
 

Secures the lower edge of the evaporator assembly inside your refrigerator. Replace if cracked, broken, or missing to restore proper alignment.

Replace missing or stripped #8-18 x 5/8-inch Torx T20 screws in your side-by-side refrigerator. Secures panels, brackets, drawer rails, and trim.

Rattling noise or warm temps? A broken evaporator fan blade disrupts air circulation. This repair takes 30-45 minutes with basic tools and our video guide.

The Lid Bumper is an OEM part for GE refrigerators. It is designed to provide cushioning and protection for the refrigerator lid, preventing damage and ensuring smooth, quiet closing. 

Causes of a bad Lid Bumper can include deterioration over time due to frequent use, exposure to temperature variations, or damage from accidental impacts. A worn or damaged bumper may no longer provide adequate cushioning, leading to potential damage to the lid or the refrigerator itself.

Symptoms of a bad Lid Bumper include:

• The refrigerator lid closing too hard
• Unusual noises when closing the lid
• Visible wear or cracks on the bumper

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Rubber grommet that seals and cushions where the evaporator fan motor shaft mounts. Replace if cracked, worn, or missing to eliminate noise and vibration.

Secures and seals water line connections in your refrigerator's dispensing system. Replace if leaking or loose to prevent water damage. Confirm fit.

This evaporator fan motor dust cap is an authentic OEM replacement part found on refrigerator and freezer fan motors. This dust cap prevents the fan motor bearing and housing from being damaged by dirt and debris. If the dust cap is cracked or broken, the fan may make loud squealing noises. If the dust cap is not removed and replaced, the fan could stop working and ultimately cause the refrigerator's temperature to be affected. To start, disconnect the power and water to the refrigerator. Remove food from the freezer so that the back panel of the freezer can be accessed to reach the fan. Remove the ice maker and set it outside the freezer. Disconnect the fan and take it out of the freezer to expose the fan's shaft and the dust cover. Pry the dust cover off and install the new one. Replace the fan and cover. Reconnect the wires and reinstall the icemaker. Put the food back in the freezer. Reconnect the power and water.The evaporator fan motor dust cap is a white plastic part that is sold individually. This dust cover is made for use in refrigerators manufactured by General Electric, Hotpoint, and Kenmore.

This black lever assembly operates the freezer door handle mechanism, allowing smooth opening and secure closing of the freezer compartment. It connects the external handle to the internal door latch system. Replace this part if your freezer door handle is loose, won't open the door, or if the handle feels disconnected when pulled.

Replacement door closure spring for refrigerator hinges. Installs on door hinge assembly to provide tension for proper closing. Needed when broken or worn.

Fastens refrigerator panels, brackets, and internal components. Replace this screw if the original is missing, stripped, or damaged to restore secure mounting.