Parts for Ge ZICP360SLCSS: 03 - Freezer Section, Trim & Components Parts

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

Fix uneven cooling or defrost issues with a new temperature sensor. Most DIYers complete this repair in under an hour with basic tools and our video.

Interior light not working when door opens? This light switch controls refrigerator illumination. DIY-friendly install takes 30-45 minutes with video.

Plastic tubing that routes water through your refrigerator's system. Replace if cracked, brittle, kinked, or leaking to restore proper flow and prevent damage.

Ice maker not producing ice or stopped working? This ice maker kit restores ice production. Includes full assembly for harvesting and ejecting ice.

Fixes uneven cooling in fresh food section. This air diffuser directs chilled air for consistent temperatures. Simple DIY repair restores airflow.

Ice maker water fill tube kit for refrigerators. Replaces cracked, damaged, or leaking tubing that routes water from inlet to ice maker. Includes mounting hardware.

Left hand base channel provides lower cabinet support for your freezer. Replace if cracked, bent, or damaged to restore proper alignment and stability.

Nylon hinge arm secures and guides refrigerator doors for smooth pivoting and alignment. Replace if cracked, broken, or worn to restore door support.

Shoulder-style bolt that secures moving parts in refrigerator mechanisms. Replace if worn, damaged, or missing to restore proper alignment and smooth operation.

Spring should have GOLD color.

Bottom hinge bushing guides the refrigerator door hinge pin for smooth pivoting. Replace if worn, cracked, or missing to restore proper alignment.

Ice maker not filling or water spilling? This fill cup directs water into the ice maker mold for proper ice production. Simple clip-on install.

This corner key assembly secures and finishes a refrigerator door corner, restoring proper alignment and a clean appearance. It replaces a cracked, broken, or missing corner piece to help the door close evenly and look factory-original. What it does:

• Provides structural support at the door corner to maintain proper edge alignment
• Covers and protects the underlying corner area from damage and wear
• Helps reduce visible gaps or misalignment that can affect sealing
• Restores the cabinet's finished appearance after impact or deterioration

• One corner key assembly

• Disconnect power to the appliance before starting any repair
• Remove door or trim per manufacturer instructions to access the corner area
• Install with original fasteners or clips; do not force or over-torque plastic snaps
• If hinge or door alignment issues persist, inspect associated hinges and gaskets

Removable plastic bin that collects and stores ice from your ice maker. Replace if cracked, broken, or missing to restore proper ice storage.

Large freezer basket for bottom-mount refrigerators. Replaces cracked, broken, or missing storage baskets in the freezer compartment. Direct fit.

Slide support assembly that stabilizes and guides your refrigerator freezer drawer. Replace when the original is cracked, broken, or worn to restore alignment.

Freezer drawer slide rail for bottom-mount refrigerators. Replace if drawer is difficult to open, rail is cracked, or drawer jams when sliding out.

Truss head screw for refrigerator assembly and panel mounting. Replace missing, stripped, or damaged screws during repairs or part installations.

Size: 10-32 GXTT FLP.595 S

Size: 1/4 inch diameter.

Small freezer basket for bottom-mount refrigerators. Organizes frozen items in the freezer drawer. Replace if cracked, broken, or missing. Easy install.

Mounts to the freezer wall to hold the upper basket in place. Replace if broken, missing, or cracked to restore proper alignment and smooth sliding.

Plastic guide that supports and aligns the upper freezer shelf along its track. Replace if cracked, broken, or worn to restore smooth sliding motion.

Upper freezer basket slide rail for bottom-mount refrigerators. Guides the top basket for smooth gliding. Replace if cracked, warped, or broken.

Upper case hinge for refrigerator doors. Secures and allows smooth door pivoting. Replace if cracked, broken, or worn to restore proper door alignment.

Freezer drawer slide shim for bottom-mount refrigerators. Replaces worn, cracked, or missing shims that support smooth drawer operation.

Right side case trim for refrigerators. Covers the side panel edge for a finished look. Replace if cracked, broken, or missing for proper appearance.

Replaces the stud spring on refrigerator and freezer doors. Needed when the original spring is broken, worn, or missing, affecting door alignment.

Left-hand link actuator for refrigerator linkage systems. Replaces worn, broken, or damaged actuators that cause erratic movement in mechanical linkages.

White 12-24 screw secures panels, trim, and brackets inside your refrigerator. Replace missing, stripped, or damaged fasteners to restore stability.

This shear pin secures the washer agitator to the drive shaft and protects the transmission by designed failure when the agitator binds. It's a small, low-cost part that prevents costly gear or motor damage. What it does:

• Locks the agitator to the drive shaft so the washer can agitate and spin
• Designed to break (shear) if the agitator is jammed, preventing transmission or motor damage
• Commonly replaced when the agitator spins freely or the washer won't agitate
• Small part that restores proper mechanical coupling between agitator and drive

• One shear pin

• Disconnect power and water before starting any repair
• Access usually requires removing the agitator; follow your model's service instructions
• Verify shaft and agitator mating surfaces for wear or damage and replace if needed

This track shelf is the replacement door shelf track that secures a refrigerator door shelf in place, restoring stable storage and preventing the shelf from shifting or falling during normal use. What it does:

• Provides the mounting channel that a door shelf or retainer sits in to hold items on the refrigerator door
• Replaces a cracked, worn, or broken track that lets a door shelf tilt or slide out
• Restores proper shelf alignment so door bins sit securely and items stay in place
• Compatible with typical snap-in or screw-mounted door shelf assemblies

• Remove all items from the door shelf and, if needed, remove the shelf before replacing the track
• Power off or unplug the appliance only if access requires it; otherwise take care to avoid sharp edges
• Align the track with the door mounting locations and press or secure into place until fully seated
• If hardware is present, retain and reuse existing screws/clips; replace only with manufacturer-specified fasteners

Mounting screw for refrigerators and freezers. Secures internal components and panels. Replace if stripped, missing, or damaged during maintenance.

A single replacement screw used to secure appliance panels, trim, and internal brackets so components stay aligned and reduce rattling. Simple, direct-fit fastener for restoring proper mounting and stable operation. What it does:

• Secures panels, mounting brackets, trim pieces and other appliance components
• Helps stop rattling, vibration, or loose panels caused by missing or stripped fasteners
• Restores proper alignment of doors and access panels when original screw is lost or damaged
• Matches the OEM fastening point for a straightforward hardware replacement

• Disconnect power to the appliance before working on electrical components or access panels
• Use the correct screwdriver to avoid stripping the head; match drive type to the screw
• Tighten firmly but do not overtighten—stop when snug to avoid damaging threads or parts
• Keep removed fasteners organized and compare with the replacement to ensure correct fit