Parts for Ge DFE29JSDCSS: Freezer Shelves Parts

Filter Material: Carbon Block. Micron Rating: 0.5. Flow Rate: 0.5 gpm. Operating Pressure: 120 psi. Approximate dimensions: 10" x 1-3/4"

The GE Refrigerator Water Filter RPWFE is an OEM part for GE refrigerators. This advanced water filter is crucial for removing contaminants and impurities from your refrigerator's water supply, ensuring you have access to clean, fresh-tasting drinking water and ice. Utilizing a state-of-the-art filtration process, the RPWFE filter is capable of reducing various contaminants, including lead, chlorine, and five pharmaceuticals, providing peace of mind about the quality of your water.

Over time, water filters can become clogged with particles and contaminants, leading to a decrease in water flow and a reduction in the effectiveness of filtration. It's important to replace your refrigerator water filter as recommended by the manufacturer, typically every six months, to ensure optimal performance and maintain the quality of your water.

Symptoms of a filter needing replacement include:

• Reduced water flow from the dispenser.
• Unpleasant taste or odor in the water or ice. 
• The refrigerator's water filter indicator light turns on

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

This mounting screw secures appliance components to the chassis for a tight, rattle-free fit. Replacing a missing, stripped, or corroded fastener helps keep panels, brackets, or burner assemblies properly aligned and secure.

• Fastens designated parts to the appliance frame or mounting points
• Helps maintain proper alignment of panels, trim, brackets, or burner assemblies
• Restores hold when the original screw is worn, rusted, or lost
• Symptoms include loose or wobbly components, rattling/vibration, or visible gaps

• Disconnect power; allow all surfaces to cool. For gas units, also shut off the gas supply.
• Use the correct driver/bit; avoid cross-threading.
• If mating threads or clip/nut are damaged, repair or replace them before installing.
• Tighten until secure; do not overtighten to prevent stripping.

The Basket Bottom Asm is an OEM part for GE refrigerators. This assembly is specifically designed to fit in the bottom freezer compartment, providing a convenient and organized storage solution for your frozen foods.

A bad bottom freezer basket assembly can occur due to wear and tear, accidental damage, or other factors. If you notice symptoms such as broken wires, a loose fit, or difficulty in sliding the basket, it may be time to replace it with a new one.

Symptoms of a bad bottom freezer basket assembly include:

• Broken wires
• Loose fit in the freezer compartment
• Difficulty in sliding the basket in and out

Improve your freezer storage and organization by replacing the faulty bottom freezer basket assembly with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

The Lower Drawer Gear is an OEM replacement part for GE refrigerators. It plays an important role in allowing smooth operation of the lower freezer drawer. The drawer gear mechanism helps guide and support the drawer assembly during opening and closing. 

Symptoms of a bad lower drawer gear include:

• The drawer failing to slide open or close properly
• Increased resistance or friction when operating the drawer  
• Noisy or grinding sounds coming from the drawer area
• The drawer becoming misaligned or sidetracked from its rails

Causes of a bad lower drawer gear can be wear and tear over extended use. Exposure to excessive weight or strain on the drawer can potentially damage the gear components over time.

Note: Right Side

This OEM GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Left side

The Connector Gear Pinion is an OEM part for GE refrigerators. It is integral to the smooth operation of the freezer drawer, connecting the rail system and allowing the drawer to open and close effortlessly.

Causes of a bad connector gear pinion can include general wear and tear over time, excessive force applied during operation, or debris causing obstructions within the mechanism.

Symptoms of a bad Connector Gear Pinion include:

• Difficulty in opening or closing the freezer drawer
• Unusual noises such as grinding or clicking when operating the drawer
• The drawer not staying aligned or properly seated on the rails
• The drawer getting stuck or not moving smoothly

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

A replacement crossbar pinion that engages the ice-maker ejector crossbar to advance the harvest cycle. Installs on the ice maker drive assembly to restore proper rotation of the ejector and help clear ice from the mold. What it does:

• Drives the ice-maker crossbar/ejector during the harvest cycle so ice cubes are pushed out.
• Transfers rotation from the ice-maker motor/cam to the ejector crossbar.
• Common symptoms: ice maker won't advance or eject cubes, loud grinding or clicking from the ice bin, or visible broken/missing gear teeth.
• Restoring a worn or broken pinion can stop jamming and allow normal harvest cycles to resume.

• Disconnect power to the appliance before servicing; shut off the water if removing the ice maker assembly.
• Remove the ice maker per the manufacturer's instructions to access the pinion; handle plastic gears carefully to avoid damage.
• Inspect mating gears and the ejector crossbar for wear or damage and replace any damaged components to prevent repeat failure.
• After installation, restore power and run a test harvest cycle to ensure proper operation.

The Crossbar Pin is an OEM part for GE refrigerators. It is a small but essential component that secures the crossbar in place within the refrigerator's interior. This pin ensures that the crossbar, which supports various shelving and storage configurations, remains stable and functional.

Causes of a bad Crossbar Pin can include wear and tear over time, accidental impact or damage during loading or cleaning, or corrosion due to moisture exposure. These factors can compromise the integrity of the pin, leading to instability in the crossbar.

Symptoms of a bad Crossbar Pin include:

• Shelves or storage bins not sitting level
• Difficulty in adjusting or removing the crossbar
• Noticeable wobbling or instability in the crossbar

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This screw set replaces worn or missing fasteners used on the freezer door assembly to restore secure attachment of door components. Ideal for fixing loose panels and reducing rattling so the door sits and seals properly. What it does:

• Secures freezer door components and trim to the door assembly.
• Restores proper fit and alignment when screws are corroded, stripped, or missing.
• Helps eliminate door rattles and loose panels that can affect door seating.
• Matches OEM fastener type and lengths used on the freezer door assembly.

• Screw set for freezer door

• Disconnect power and empty the door area before starting work.
• Use the correct screwdriver or bit to avoid stripping heads; install screws until snug—do not overtighten.
• Keep removed parts in order and follow OEM instructions for reassembly.

The Basket Bottom Asm is an OEM part for GE refrigerators. This assembly is specifically designed to fit in the bottom freezer compartment, providing a convenient and organized storage solution for your frozen foods.

A bad bottom freezer basket assembly can occur due to wear and tear, accidental damage, or other factors. If you notice symptoms such as broken wires, a loose fit, or difficulty in sliding the basket, it may be time to replace it with a new one.

Symptoms of a bad bottom freezer basket assembly include:

• Broken wires
• Loose fit in the freezer compartment
• Difficulty in sliding the basket in and out

Improve your freezer storage and organization by replacing the faulty bottom freezer basket assembly with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

The Basket Bottom Asm is an OEM part for GE refrigerators. This assembly is specifically designed to fit in the bottom freezer compartment, providing a convenient and organized storage solution for your frozen foods.

A bad bottom freezer basket assembly can occur due to wear and tear, accidental damage, or other factors. If you notice symptoms such as broken wires, a loose fit, or difficulty in sliding the basket, it may be time to replace it with a new one.

Symptoms of a bad bottom freezer basket assembly include:

• Broken wires
• Loose fit in the freezer compartment
• Difficulty in sliding the basket in and out

Improve your freezer storage and organization by replacing the faulty bottom freezer basket assembly with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This stopper divider holds and positions a refrigerator drawer or shelf divider to keep contents separated and prevent sliding. Durable molded plastic replaces a worn or broken stop to restore proper drawer alignment and function. What it does:

• Stops and anchors the refrigerator drawer/divider to prevent shifting during normal use
• Restores correct drawer travel and alignment when the original stop is cracked or missing
• Helps maintain organized storage by keeping divider panels in place
• Works with compatible OEM drawer and divider assemblies to ensure proper fit

• One stopper divider part as shown

• Basic hand tools may be required; inspect mounting area for debris or damaged clips before installing
• Align and snap or slide the stopper into the factory location until it seats securely
• Do not force parts into place; replace damaged clips or supports if the stopper will not seat properly
• Unplug or power off the appliance before inspecting interior components for safety

This replacement stopper secures the freezer divider so bins and shelves stay aligned, preventing shifting and gaps that can affect storage. Simple, direct fit for restoring proper divider positioning. What it does:

• Holds the freezer divider in place to keep bins and shelves aligned
• Prevents the divider from sliding or dropping during normal use
• Helps maintain organized cold storage and reduces shifting of contents
• Commonly replaced when cracked, broken, or missing

• One freezer divider stopper

• Remove food and empty the affected bin before starting
• Usually snaps into the divider track or mounting slot; inspect mating surfaces for damage
• Use basic hand tools only if needed; do not force the part into place

This push-in fastener secures trim, panels, and plastic components on compatible appliances to prevent rattling and hold parts in place. Simple clip design keeps panels aligned without screws or specialized hardware. What it does

• Holds plastic trim, interior panels, and lightweight assemblies in place
• Replaces worn or broken push retainers that cause loose or vibrating panels
• Helps restore proper fit of door liners, kick plates, and interior housings
• Commonly used where a snap-in plastic retainer is required

• Push into the matching hole until the head seats flush; no tools typically required
• Inspect mating hole and surrounding material for damage before installation
• Remove power and follow appliance safety instructions when working near electrical components
• If fastener does not seat correctly, confirm correct part and hole size before forcing

This left-hand slide bracket assembly supports and guides a refrigerator drawer so it opens and closes smoothly. It replaces a worn or broken left slide bracket to restore proper drawer alignment and movement. What it does

• Mounts to the cabinet and holds the drawer glide/rail in place for stable operation
• Restores smooth drawer travel when the original bracket is cracked, bent, or broken
• Prevents drawer sagging, misalignment, or falling when loading items
• Works with the existing glide components to maintain proper drawer positioning

• One left-hand slide bracket assembly

• Disconnect power and remove drawer contents before starting work
• Remove the affected drawer and any trim to access the bracket; keep track of screws and clips
• Use appropriate hand tools; avoid forcing parts to prevent damage to surrounding components
• Inspect companion glide/rail parts and fasteners; replace damaged items for a complete repair

This replacement slide supports and guides the refrigerator's upper freezer basket so it glides smoothly in and out. Replacing a cracked or worn slide restores easy access and helps keep the basket aligned during everyday use.

• Provides the track for the upper freezer basket to slide smoothly
• Keeps the basket aligned during opening and closing
• Helps prevent scraping, binding, or the basket coming off its track
• Common signs of failure: basket hard to move, sits crooked, rubs the liner, or visible cracks/broken tabs

• Disconnect power to the refrigerator before servicing
• Remove food and lift out the upper basket as needed for access
• Release or unfasten the damaged slide from its mounting points (clips or screws vary by model)
• Install the new slide securely and test basket travel for smooth operation

This silicon controlled rectifier (SCR) is a replacement power-control semiconductor used to regulate current in appliance power circuits, helping restore proper operation of heating and motor circuits that rely on solid-state switching. What it does:

• Acts as a switch to control and modulate electrical current in the appliance power path
• Enables regulated power delivery to heating elements or motor circuits when driven by the control board
• Commonly replaced when the appliance shows intermittent power, no heat, or erratic on/off behavior in the affected circuit
• Works as a direct replacement for the OEM SCR with identical mounting and electrical fit when specified by part number

• Disconnect power to the appliance before starting any repair to avoid shock or damage
• Observe basic ESD precautions when handling the SCR and avoid touching semiconductor leads

The Top Freezer Basket Slide Bracket is an OEM replacement part for GE refrigerators. It is designed to securely hold the freezer basket slide in place, allowing for smooth and effortless movement when accessing items stored in the freezer. It provides stability and support to the basket, preventing it from tipping or falling out during use.

A bad top freezer basket slide bracket can occur due to regular wear and tear or accidental damage. If you notice symptoms such as a wobbly or unstable freezer basket, difficulty in sliding the basket in and out, or the basket not staying securely in place, it may indicate a need to replace this part.

Symptoms of a bad top freezer basket slide bracket include:

• Wobbly or unstable freezer basket
• Difficulty in sliding the basket in and out
• Basket not staying securely in place

Restore your freezer organization by replacing the faulty top freezer basket slide bracket with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

The Refrigerator Slide Lower Freezer is an OEM replacement part for GE refrigerators. It is a sliding component designed to facilitate smooth and effortless access to the lower freezer compartment. This OEM part ensures that the lower freezer drawer can glide in and out seamlessly, allowing for convenient storage and retrieval of frozen items.

Symptoms of a bad Refrigerator Slide Lower Freezer include:

• Difficulty opening or closing the lower freezer drawer
• Freezer drawer catching or sticking during operation
• Noisy or grinding sounds when sliding the drawer
• Drawer not staying in position when opened or closed

Causes of a bad lower freezer slide can include wear and tear from repeated use, damage from mishandling or overloading, or issues with the slide mechanism itself. Over time, the slides may become worn, misaligned, or obstructed, leading to operational problems.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore refrigerator models.

This left-side lower freezer slide restores smooth drawer movement and proper alignment in the freezer compartment. It replaces a worn or damaged slide to help the drawer open and close reliably. What it does:

• Replaces the left lower freezer drawer slide that guides the drawer on its track
• Restores smooth, even sliding and prevents the drawer from sticking or binding
• Helps keep the drawer properly aligned so it opens and closes without catching
• Useful when the existing slide is bent, cracked, or worn and affects drawer operation

• Disconnect power and remove food from the drawer area before starting
• Typically installs onto the freezer cabinet and drawer track; basic hand tools may be required
• Align slide with factory mounting points and secure hardware; test drawer movement after installation

The Icemaker Fill Cup is an OEM replacement part for GE refrigerators responsible for directing the water flow into the icemaker, allowing for the creation of ice cubes. It securely attaches to the icemaker, preventing any leaks or spills that could disrupt the ice production.  

A bad fill cup can occur due to several factors. Common causes include cracks, damage, or wear and tear over time. If you notice symptoms such as leaks around the icemaker, improper ice production, or water overflow, it may indicate a need to replace the fill cup.

Symptoms of a bad fill cup include:

• Leaks around the icemaker area
• Insufficient or inconsistent ice production
• Water overflow or spills

Restore your refrigerator's ice-making capabilities by replacing the faulty fill cup with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

The Icemaker is an OEM component specifically designed for GE refrigerators. Located within the freezer compartment, the icemaker automatically produces batches of ice for convenient access.

Causes of a bad icemaker can include wear and tear of mechanical parts from years of producing ice. Mineral buildup may also clog components and impact performance over time.

Symptoms of a bad icemaker include:

• Failure to produce ice or very slow production  
• Ice cubes joining together in clumps or odd shapes
• Loud grinding sounds emanating from the assembly
• Leaks or water drips detected around the unit

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models. 

This right-hand freezer holder slide secures a freezer shelf or drawer in place so it operates smoothly and stays aligned. It replaces a worn or broken slide to restore proper shelf support and prevent slipping or binding. What it does

• Guides and supports the freezer shelf/drawer on the right side for smooth in-and-out movement
• Replaces cracked, broken, or worn plastic slide hardware
• Helps stop shelves or drawers from sagging, catching, or sliding out unexpectedly
• Works with the freezer compartment's shelving system to maintain proper alignment

• Disconnect power to the appliance before beginning any repair
• Typically replaces the existing right-side slide; remove the shelf/drawer to access mounting points
• Handle plastic parts gently to avoid cracking; inspect adjacent clips or supports for wear

This left-side freezer holder slide secures and guides the freezer drawer for smooth opening and closing. Replacing a worn or broken slide restores proper drawer alignment and helps prevent sagging or sticking. What it does:

• Supports the freezer drawer on the left side and keeps it aligned during use
• Guides drawer movement for smooth opening and closing
• Replaces damaged, bent, or missing slides that cause binding or uneven drawer travel
• Helps prevent the drawer from sagging, slipping, or coming off its track

• Disconnect power before servicing to avoid electrical hazards
• Remove freezer contents and a drawer or panel as needed for access
• Compare the old slide to ensure correct left/right orientation before installing
• Use basic hand tools; do not force parts—replace any damaged mounting hardware

A #8-18 x 9/16-inch hex washer head screw used to secure panels and components in appliances. Provides a proper fit for fast, reliable fastening when replacing missing, damaged, or stripped screws. What it does:

• Secures panels, brackets, and trim to keep components aligned and stable.
• Restores proper fastening when threads are stripped, the original screw is missing, or a head is damaged.
• Helps stop rattling or loose parts caused by worn or broken fasteners.
• Fits applications requiring a #8-18 thread with a 9/16" length and hex washer head style.

• Verify thread size, head style, and length before installation.
• Use the correct hex driver or socket to avoid cam-out or head damage.
• Do not overtighten; snug until secure to avoid stripping threads or deforming parts.
• Disconnect power and follow appliance-specific safety steps.

This is a single #10-18 x 3/4 inch flat-head screw used to secure panels and components in appliances. It replaces worn or missing fasteners so parts stay properly mounted and aligned. What it does:

• Fastens appliance panels, brackets, and components with a flat-head finish for flush mounting
• Replaces stripped, rusted, or missing screws that cause loose or rattling parts
• Provides a secure threaded connection for consistent operation
• Compatible where a #10-18 thread, 3/4" length flat-head screw is specified

• One (1) screw, #10-18 x 3/4 in., flat head

• Use the correct screwdriver bit (flat or Phillips depending on head style) and avoid over-tightening to prevent stripped threads
• Disconnect power to the appliance and follow manufacturer safety procedures when accessing internal components
• Dispose of damaged hardware and replace with matching specifications for safe operation

The Striker Light Switch is an OEM component specifically designed for GE refrigerators. Located on the refrigerator door, it controls interior lighting functions.

Causes of a bad switch can include wear from opening the door frequently or water damage over time.

Symptoms of a failed switch include: 

• Lights not turning on when the door is opened  
• Lights remain illuminated all the time even when closed
• Flickering or unresponsive lighting behavior

This switch utilizes a striker plate activation mechanism that triggers interior lights based on door position - open or closed. A replacement ensures lighting convenience and energy efficiency. 

This genuine OEM GE part restores dependable on/off lighting control through the normal door operation process. Compatible with additional brands including Hotpoint, RCA, or Kenmore models.

This spring feeler arm is the replacement sensing arm used with the refrigerator ice maker assembly to detect ice level and help actuate the ice-making mechanism. Restores proper ice sensing and helps prevent overfill or stoppage. What it does:

• Acts as the ice maker's feeler/bail arm to detect when the ice bin is full or empty.
• Triggers the ice maker to stop or continue cycles based on ice level.
• Helps prevent overfilling and reduces ice production problems caused by a bent or broken arm.
• Can stop erratic ice maker behavior when the original arm is damaged or worn.

• Disconnect power to the refrigerator before beginning any repair.
• Handle the arm carefully and inspect the ice maker mounting points for damage before installation.
• Reuse factory hardware if undamaged; replace any stripped or missing fasteners.

This ice maker feeler arm senses the ice level in the bin and controls when the icemaker starts and stops. Replacing a bent, missing, or stuck arm restores correct shutoff and helps prevent overfilling or no-ice conditions.

• Monitors the ice bucket level and raises/lowers to start or stop ice production
• Shuts the icemaker off when the bin is full; allows production when lowered
• Common symptoms: ice maker won't stop making ice/overflows, no ice when the arm is stuck up, loose or missing arm
• Restores proper on/off control of the icemaker cycle

• Disconnect power and turn off the water supply before servicing
• Remove the ice bin and, the icemaker assembly to access the arm
• Transfer any reusable hardware; seat the arm fully in its pivot points so it moves freely
• Restore power, lower the arm to the On position, and allow time for the icemaker to cycle

This mounting plate secures the refrigerator ice maker assembly to the freezer compartment, providing a stable support that helps maintain proper alignment and reliable ice production. What it does:

• Anchors the ice maker to the freezer cabinet so it stays securely positioned
• Prevents movement or misalignment that can cause noisy operation or ice delivery issues
• Helps maintain correct spacing for water fill and ice ejection functions
• Supports a solid electrical and mechanical connection for consistent performance

• One mounting plate

• Designed for direct replacement of the original mounting plate
• Shut off water supply and disconnect power before beginning any repair
• Use appropriate fasteners and torque per manufacturer guidance; avoid over-tightening