Parts for Ge GFSS6KKYCSS: 02 - Fresh Food Doors Parts

The water filter is an OEM part for GE refrigerators. This filter removes or reduces various contaminants.

Features and Benefits:

• Easy DIY replacement, typically mounted inside the refrigerator at the back of the compartment.
• Removes or reduces various contaminants in your water and ice, including lead, cysts, asbestos, atrazine, , taste and odor, chlorine, sediment, turbidity, and more
• NSF/ANSI 42 and 53 standards
• 6 Month lifespan filter
• Carbon Block media
• Micron rating: 0.5-1 micron (Class I)

When to replace your filter:

• Bad taste or odor in water and ice
• Cloudy or discolored ice
• Reduced water flow or pressure
• Refrigerator replace filter indicator light is on

Note: If replacing the Culligan metal canister design filter for the first time, a special adapter, part number AP2615702 is needed, which is not included with this part. The compatible bypass cap is part number AP6891551.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This is a self-tapping screw used to secure appliance panels and small components. It provides a reliable hold in sheet metal and plastic mounting points to restore proper fit and prevent rattling or loose parts. What it does:

• Fastens trim, brackets, and light-duty panels where a tapped hole is needed
• Creates its own threads in thin metal or plastic mounting points
• Helps stop vibration-related noise by securing loose panels
• Commonly used during repairs of control panels, inner liners, and external trim

• One tapping screw as shown

• Use the correctly sized screwdriver or bit to avoid stripping the head
• Drive straight and stop when snug; over-tightening can strip the mating material
• Turn power off and unplug the appliance before accessing internal panels
• If the original hole is damaged or oversized, consider using a slightly larger fastener or repair insert per manufacturer guidance

This magnet assembly secures the refrigerator door gasket for a tight, even seal to help keep interior temperatures stable and reduce energy loss. It replaces a worn or damaged magnetic strip assembly on compatible refrigerator doors. What it does:

• Provides magnetic holding force along the door edge to help the gasket seal properly
• Helps prevent warm air infiltration that can cause frost buildup or inconsistent cooling
• Restores proper door closure if a weakened or detached magnet is the cause
• Works as the magnetic component that mates with the cabinet flange to keep the door closed

• One replacement magnet assembly

• Disconnect power to the appliance before beginning any repairs
• Remove the door gasket or trim as required to access the magnet assembly
• Align the magnet assembly carefully and secure per OEM instructions to ensure an even seal

This magnet assembly replaces the magnetic strip that helps the refrigerator door seal stay tight, improving door closure and helping the appliance maintain proper temperature and efficiency. What it does:

• Replaces the magnetic sealing strip in the door gasket to help the door stay closed
• Restores a strong door seal to reduce cold air loss and limit frost buildup
• Helps prevent warm-air leaks that can cause the compressor to run more often
• Addresses symptoms such as a door that won't fully latch, visible gaps at the seal, or excessive frost in the freezer

• Disconnect power to the appliance before beginning any work
• Remove door trim or gasket; the magnet may snap or slide into a channel or require adhesive
• Handle the gasket and magnet carefully to avoid tearing or misalignment; ensure the magnet sits evenly along the door edge

This side door handle assembly is made for use on refrigerators. This component is used to open and close the refrigerator door. There are two of these handles on each refrigerator unit. One goes on the freezer door and the other on the refrigerator door. This part only includes one handle.This component is held into place with screws. If the screws and the handle become stripped, a new handle will be needed. The replacement process is easy and only requires a screwdriver. Since the door will need to be open during this process, make sure that any food that will deteriorate is placed in a temperature-safe location.The side door handle assembly is compatible with refrigerators that are manufactured by both GE and Samsung brands. It is sold individually and is a genuine OEM part that has been sourced directly from the manufacturer.

This upper door bin restores secure, usable storage on your refrigerator door. Replace a cracked, loose, or missing bin to keep bottles and condiments organized and to help prevent items from tipping or falling when the door moves.

• Provides a dedicated shelf on the door for jars, bottles, and condiments
• Replaces a broken, warped, or missing bin to maintain proper fit and function
• Helps keep items upright and reduces spills during door opening/closing
• Common symptoms: cracked bin, won't stay seated, falls off, or missing bin

What's included: 1 upper door bin Install notes:

• Disconnect power and remove items from the affected door area
• Lift the old bin straight up to release it from the door liner tabs/slots
• Align the new bin at the upper position and press down until both ends snap in evenly
• Verify the bin is fully seated and secure before reloading items

This refrigerator door gasket seals the edge of a French-door fridge to help keep cold air in and warm air out, reducing frost and helping the appliance maintain stable temperatures and efficient operation. What it does:

• Creates an airtight seal along a French-door refrigerator edge to prevent air leaks
• Helps reduce frost buildup and condensation by keeping cold air inside
• Can stop temperature fluctuations that cause food spoilage
• Often shows problems as visible gaps, a torn or warped seal, or difficulty keeping the door fully closed

• Inspect and clean the door margin and gasket seating area before installation to ensure a proper seal
• Handle the gasket carefully; align evenly and avoid stretching or pinching during installation
• Follow the refrigerator manufacturer's instructions and use the correct fasteners or retainers if required

The French Door Spring Pin is an OEM part for GE refrigerators. It plays a crucial role in the proper functioning of the refrigerator's French doors by ensuring they close securely and smoothly. This spring pin helps maintain the alignment and tension of the doors, contributing to the overall efficiency and usability of the appliance.

You should replace this French door spring pin if it becomes damaged or fails. Causes of a bad spring pin can include wear and tear over time, accidental damage, or corrosion due to exposure to moisture.

Symptoms of a bad French door spring pin include:

• Difficulty in closing the refrigerator doors
• Doors not staying securely closed
• Misalignment of the French doors
• Unusual noises when opening or closing the doors

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This is a French spring, or French divider door spring. It is used in refrigerators. This part allows the doors to open and close. It is located in the door of the fridge. A new French divider door spring may be needed if the door is stuck or is coming off of its hinges. This repair requires only a standard household toolkit. To replace the spring simply remove the old one and replace the part with a new, working piece. Be sure not to bend the spring while installing it as it will not fit in as the replacement part. This is a genuine OEM part. It is sourced directly from the manufacturer and is sold individually. This specific French Divider Door Spring is compatible with appliances made from General Electric.

This is an ice chute and funnel assembly for refrigerators with ice dispensers on their doors. The chute opens upon the user's command input and releases ice into a glass or other container placed underneath it. With use, because of misuse, or as a result of accidental damage, part or all of the ice chute door and funnel may malfunction or fail entirely. When this happens, a replacement part is required to continue using the ice dispensing feature.If the ice chute no longer dispenses ice, or if it is dispensing too much or too little ice, it's a good indication that there is something wrong with this part of the appliance. It's a quick repair. It is always recommended to unplug the device before beginning the replacement. Move any food that could spoil while the repair is being completed.This refrigerator ice dispenser ice chute door and funnel assembly is a genuine OEM replacement part. It is sourced directly from the manufacturer. It is sold as an individual unit and made of durable materials. The replacement part is compatible with several models of refrigerators manufactured by General Electric, Hotpoint, and RCA.

A self-tapping screw used to fasten appliance panels and components where a threaded hole is formed as the screw is driven. Provides a secure hold for trim, brackets, and light assemblies during repairs. What it does:

• Cuts its own mating thread in sheet metal or thin plastic to secure panels and brackets
• Helps hold trim, access panels, or internal components in place
• Commonly used where a tapped hole is not present or repair requires a replacement fastener
• Can prevent loose parts and rattles caused by missing or damaged screws

• Unplug the appliance before servicing to avoid electrical or mechanical hazards
• Use the correct screwdriver or bit to avoid stripping the screw head
• Start the screw straight and apply steady pressure; do not overtighten to avoid cracking plastic or stripping metal
• Replace only with the exact part number to ensure proper fit and function