Parts for Ge GFSS6KIXBSS: 06 - Fresh Food Section Parts

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

A small mounting clip that secures a plastic housing or cover to the appliance frame, keeping panels aligned and internal components protected. Replaces a worn or broken clip to restore proper fit and reduce rattles. What it does:

• Secures a housing or access cover to the appliance cabinet so panels stay aligned
• Keeps wiring and internal components covered and protected from debris
• Stops covers from sagging, rattling or falling off due to a broken clip
• Helps maintain normal airflow paths and panel fit where applicable

• Always disconnect power to the appliance before inspecting or servicing panels
• Typically fastens with snap-in engagement or a small screw; basic hand tools may be required
• Handle plastic panels and clips gently to avoid cracking; replace any damaged adjacent fasteners

Tapping screw for dryer or refrigerator assembly. Replace this fastener if cracked, stripped, or missing during panel or component installation.

Retaining spring secures the fan blade to the motor shaft in your refrigerator. Replace if spring is broken, missing, or loses tension.

This temperature sensor monitors internal refrigerator temperatures and relays them to the control, helping the unit maintain consistent cooling. Replacing a failed sensor restores accurate temperature regulation and more reliable operation. What it does:

• Measures compartment or evaporator temperature and sends a resistance signal to the control board
• Helps the control modulate compressor and fan run times for proper cooling
• Typical failure signs: sections too warm or too cold, erratic temperatures, or running longer than normal
• Causes inaccurate temperature readings compared to setpoints

• 1 temperature sensor assembly

• Disconnect power before servicing
• Access the sensor in the affected section; release any cover/clip and unplug the connector
• Route the new sensor's wiring like the original and ensure it's fully seated in its holder or clip
• Restore power and allow up to 24 hours for temperatures to stabilize

This defrost thermostat monitors temperature in your refrigerator's freezer section to control the defrost cycle. It signals when frost buildup requires melting and stops the defrost process when complete. Replace this part if you notice excessive frost buildup, ice blocking air vents, or inconsistent cooling.

Secures temperature sensor in place for accurate readings. Replace if loose, cracked, or sensor reads incorrectly. Confirm fit with your model number.

Houses and protects the evaporator coil in your refrigerator. Replace this cover if cracked, broken, or missing to restore proper airflow and drainage.

Secures your refrigerator's evaporator housing cover in place. Replace if broken, loose, or missing to ensure proper airflow and cooling performance.

Replace your refrigerator light cover lens when cracked, yellowed, or broken to restore proper interior lighting. Verify fit with your model number.

Secures the light bulb assembly inside your refrigerator compartment. Replace if the holder is cracked, broken, or no longer keeping the bulb stable.

Self-tapping screw for securing refrigerator panels, brackets, and trim. Replaces missing, stripped, or damaged screws in sheet metal and plastic.

Replacement water reservoir assembly for refrigerators. Stores water for dispenser and ice maker. Replace if cracked, leaking, or frozen to restore proper flow.

Protective cover for the refrigerator water tank heater assembly. Replaces cracked, broken, or missing covers to shield heating components and maintain proper tank insulation.

Water filter head assembly holds the filter and connects water lines. Replace if you have no water flow or leaks. Confirm fit with your model number.

This water filter cover is the replacement access housing that secures the refrigerator's water filter and helps direct water through the filter for clean dispensing. Restores proper filter fit and helps prevent leaks around the filter opening. What it does

• Secures the in-line or cartridge water filter so it stays seated during operation
• Helps route water through the filter to the dispenser and ice maker
• Replaces cracked, broken, or warped covers that cause leaks or poor filter alignment
• Allows proper installation and removal of the water filter cartridge

• Disconnect power and shut off the refrigerator water supply before beginning work
• Remove the old cover carefully; inspect the filter area and seals for damage or debris
• Align the cover and filter per the refrigerator's service instructions; do not force parts
• If you see damaged seals or fittings, replace them before restoring power and water

Refrigerator too cold or freezing food? A damaged damper motor cover can cause temperature control issues. Protects damper assembly from debris buildup.

Replace your refrigerator's damper cover if the original is cracked, broken, or missing. This plastic cover installs over the air damper assembly.

Fix frozen evaporator coils or inconsistent freezing with this freezer temperature sensor. Monitors compartment temp to control compressor and defrost cycles.

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.