Parts for Ge PFCS1PJYCSS: 04 - Fresh Food Section Parts

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

Air tower duct assembly that channels cold air from freezer to fresh food compartment. Replace if cracked, broken, or causing uneven cooling airflow.

Refrigerator air tower duct that channels cold air from the evaporator to the fresh food compartment. Replace if cracked, broken, or missing parts.

Fridge running warm or uneven temps? This air tower assembly channels cold air through the refrigerator. Restores proper airflow and consistent cooling.

Seals the fresh food compartment inlet to maintain temperature and prevent air leaks. Replace if torn, cracked, or causing cooling issues. Verify fit with your refrigerator model number before ordering.

Replace your refrigerator tower fresh food gasket to restore proper sealing and prevent air leaks. Essential when doors don't seal tightly or foam shows wear. Verify compatibility with your model number before ordering.

Seals the fresh food compartment tower to prevent air leaks and maintain temperature. Replace if worn, cracked, or causing frost buildup. Verify fit with your refrigerator model number before ordering.

The Temperature Sensor Seal is an OEM part for GE refrigerators. This seal is designed to protect the temperature sensor from moisture and other environmental factors that could affect its accuracy and longevity. By providing a barrier against the harsh conditions within a refrigerator, such as humidity and temperature fluctuations, this seal ensures that the sensor can accurately monitor and control the refrigerator's internal temperature.

Causes of a malfunctioning Temperature Sensor Seal can include wear and tear over time, degrading the seal's effectiveness. Physical damage like tears or punctures can allow moisture to reach the sensor. Improper installation may leave gaps or loose areas around the sensor, compromising the seal.

Symptoms of a bad Temperature Sensor Seal include:

• Inaccurate temperature readings.
• Condensation or frost near the sensor location.
• Frequent cycling or unusual patterns in the refrigerator's cooling process.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Protective grille cover that mounts over the temperature sensor in your refrigerator. Replace if cracked, broken, or missing to properly shield the sensor.

This vertical vent duct is a direct-replacement exhaust channel that routes hot, moist air from the appliance to the home vent, helping maintain proper airflow and reduce moisture or heat buildup around the unit. What it does

• Channels exhaust air from the appliance to the household vent line.
• Helps prevent exhaust air from leaking into the room and reduces backflow.
• Common symptoms it can address: long drying cycles, excess humidity or heat near the appliance, and visible exhaust escaping into the room.
• Fits into the appliance's existing vent connection to restore correct airflow.

• Turn off and disconnect power (and gas, if applicable) before servicing.
• Verify the existing vent path is clear and the duct orientation matches appliance connections.
• Use basic hand tools; avoid crushing or kinking the duct during installation.

Vertical vent duct channels air inside your refrigerator cabinet for consistent temperature control. Replace if cracked, warped, or missing to restore airflow.

Fridge running warm or uneven temps? This air tower assembly channels cold air through the refrigerator. Restores proper airflow and consistent cooling.

Secures and seals your refrigerator's water filter cartridge in place. Replace if cracked, loose, or leaking to restore proper fit and prevent debris entry.

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

Fix uneven cooling or defrost issues with a new temperature sensor. Most DIYers complete this repair in under an hour with basic tools and our video.

Connects water supply tubing sections in your refrigerator. Replace this plastic compression union if it's cracked, leaking, or broken. Installs inline.

Houses the water filter and connects to the water supply line. Replace if water leaks, sprays during filter changes, or dispenser flow decreases. Verify model fit.

Bypass cap allows refrigerator water and ice dispensers to work without a filter installed. Replace if cracked or leaking. Confirm fit with your model.

Spacer component for refrigerator water filter housing. Ensures proper spacing and alignment. Replace if cracked, worn, or missing to restore fit.