Parts for Ge GTE18LMHGRES: Fresh Food Section Parts

Refrigerator not cooling or ice building up on evaporator coils? The defrost timer controls the defrost cycle. DIY-friendly, installs in 5 minutes.

Leveling leg threads into the refrigerator base to support and stabilize the cabinet. Replace if cracked, broken, or worn to keep your unit level.

Supports and pivots your refrigerator door for smooth opening and closing. Replace when door sags, misaligns, or won't seal properly. Confirm fit with your model number before ordering.

Replace your refrigerator's center door hinge to restore smooth door movement and maintain a proper seal. Supports door weight at the pivot point. Confirm fit with your model number before ordering.

Pivot shaft for refrigerator doors at the middle hinge. Replace if worn or bent to restore proper door alignment and smooth operation. Verify fit.

This small replacement corner cap covers and protects an appliance's outer corner trim, restoring a finished look and keeping edges from catching or chipping. It's a simple cosmetic and protective part for worn or broken corner trim. What it does:

• Covers and protects the outer corner of the appliance trim to prevent catches and chips
• Restores a clean, finished appearance where original corner caps are cracked or missing
• Helps keep trim edges aligned and reduces risk of sharp exposed edges
• Common remedy for visible damage after bumps, drops, or long-term wear

• Disconnect power to the appliance before attempting any service that requires removing trim or glass.
• Handle trim and glass carefully—wear gloves and eye protection to avoid cuts from sharp edges.
• This cap typically snaps or fits into place or secures with existing trim hardware; your model's service instructions for removal and reinstallation details.
• If the original trim or mounting clips are damaged, replacement of those items may be required for a secure fit.

Small washer that fits on refrigerator door hinges to distribute weight and reduce friction. Replace if worn, cracked, or missing to restore proper alignment.

Supports the refrigerator door at the lower pivot point for smooth opening and proper sealing. Replace if the door sags or won't close tightly. Confirm fit by model number.

Bottom hinge pin secures the refrigerator door at the base, allowing smooth opening and closing. Replace if worn, damaged, missing, or door sags.

Right front wheel assembly for refrigerators. Installs on the bottom right corner for smooth rolling. Replace if cracked, broken, or missing.

Control knob fits onto your refrigerator's control shaft to adjust temperature and settings. Replace a cracked, stripped, or missing knob for smooth operation.

Refrigerator not maintaining temperature or food spoiling? This cold control thermostat kit restores proper cycling so your unit holds consistent temps.

Foam gasket seals the water supply nozzle connection to prevent leaks and reduce vibration. Replace if worn or leaking. Confirm fit with your model number.

Vinyl sleeve that fits over rods, tubes, or wires in your refrigerator. Replace if cracked, torn, or missing to protect contact points and reduce wear.

Fix refrigerator not cycling properly or timer not advancing. This mechanical timer control harness restores power and signal routing to switches and motors.

Replace a cracked or broken control housing frame on your refrigerator. This console frame secures the control board and user interface components.

The Light Socket is an OEM part for GE refrigerators. It is responsible for holding the refrigerator's light bulb and ensuring it receives power to illuminate the interior when the door is opened.

You should replace the light socket if it becomes faulty. Causes of a bad light socket can include wear and tear from regular use, electrical issues such as short circuits or power surges, and corrosion from moisture exposure.

Symptoms of a bad light socket include:

• The refrigerator light not turning on when the door is opened
• Flickering or intermittent light operation
• Visible damage or corrosion on the socket
• The light bulb not fitting securely or falling out

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Fix interior lights that won't turn on, stay on constantly, or delay when opening the door. This switch replacement takes 10-15 minutes with basic tools.

This genuine fastener secures appliance components such as panels and brackets. Replacing a missing or stripped screw restores proper fit and helps reduce vibration or rattling. Features 12-24 threads and an approximate 0.785-inch length. What it does:

• Fastens panels, brackets, covers, and other hardware points in the appliance
• Helps maintain proper alignment and a tight fit of components
• Replaces damaged, stripped, or missing hardware
• Common symptoms include loose or rattling parts and hardware that won't tighten

• One screw

• Disconnect power before servicing; shut off water supply if working near water components
• Start the screw by hand to avoid cross-threading; replace one-for-one in the original location
• Use the correct driver bit for the head style; tighten snugly without overtightening into plastic or thin metal