Frigidaire Dryer Filter

The Lint Filter is an OEM part for Frigidaire dryers. This component is crucial for trapping lint and debris that come off clothes during the drying process. By capturing this lint, the filter prevents it from clogging the dryer’s internal mechanisms and vent, thereby enhancing the efficiency of the dryer and reducing the risk of fires. 

Symptoms of a bad Lint Filter include:

• Excessive lint escaping back into the dryer drum or venting system.
• Tears or holes in the filter mesh that fail to trap lint.
• Difficulty fitting the filter into its slot due to warping or damage.
• Longer drying times or overheating, indicating poor air flow.

Causes of a bad lint filter can include normal wear and tear from regular cleaning and use, accidental damage during removal or cleaning, or degradation from exposure to high heat.

The Lint Filter is an OEM replacement part for Frigidaire, Electrolux, Gibson, and Kenmore dryers.

The Lint Trap is an OEM part for Frigidaire dryers. It helps in capturing lint and debris generated during the drying process, preventing them from clogging the dryer vent and exhaust system.

Causes of a clogged or faulty lint trap can include excessive lint accumulation, damage to the trap screen, or improper installation.

Symptoms of a bad lint trap may include:

• Longer drying times
• Reduced drying efficiency
• Visible lint accumulation in the dryer drum or on clothes
• Excessive heat inside the dryer

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Color: white. It measures about 13 inches wide by 11-1/2 inches high.

This EMI line filter reduces electrical interference on the incoming power to help protect the appliance's electronics and ensure stable operation. A failed filter can leave the unit dead, intermittently power-cycling, or tripping a breaker.

• Filters electromagnetic interference (EMI) on the AC line
• Helps protect the control board and other sensitive circuits
• Common symptoms: no power, intermittent power, or breaker/fuse trips when the unit starts
• Typically located near the power-cord entry or main control

• Disconnect power before servicing; allow a few minutes for any capacitors to discharge
• Note and label wire positions; move wires one at a time to the new filter
• Secure the filter to its mounting bracket and ensure the ground connection is tight
• Inspect wiring for shorts or damage before restoring power and testing

This adapter tube assembly connects sections of the appliance's water line to create a secure, leak-resistant path for water flow. Replace it if the tube is cracked or the connection no longer seals properly to prevent leaks and restore flow.

• Connects water tubing between components within the appliance's water system
• Helps maintain a tight, leak-resistant seal at the joint
• Restores proper water flow when a tube or connector is damaged
• Typical symptoms: water leaking at the connection, reduced or no water flow, visible cracks/kinks, loose fit

• Disconnect power and shut off the water supply before servicing
• Relieve line pressure and place a towel or pan to catch any residual water
• Note routing and orientation before removal to ensure correct reassembly
• After installation, restore water and check all connections for leaks

Replacement grill trim that restores your appliance's exterior finish and helps direct airflow. Use this grill when the original piece is cracked, missing, loose, or cosmetically damaged to regain a clean, finished appearance. What it does:

• Covers and protects internal components behind the appliance front or vent area.
• Helps direct airflow and reduce drafts around the appliance opening.
• Prevents debris or fingers from contacting internal parts.
• Stops rattling or vibration caused by a bent or loose grill.
• Restores the appliance's original look when the factory grill is damaged.

• Disconnect power at the breaker and allow the appliance to cool before starting any work.
• Remove existing fasteners or clips; retain original screws if they are reusable.
• Align the new grill, then secure with the original hardware; avoid over-tightening to prevent cracking.

This lint filter is the removable screen that traps lint and debris from dryer exhaust so air flows freely and loads dry more efficiently. Designed as a direct replacement for the factory lint-trap element. What it does

• Captures lint, fibers and small debris from the dryer drum exhaust to help prevent clogs.
• Restores proper airflow that can reduce long dry times and help the dryer operate more efficiently.
• Helps prevent lint buildup in the dryer vent and blower housing, lowering risk of overheating.
• Easy to remove and clean for routine maintenance and improved drying performance.

• One lint filter (screen) as shown.

• Disconnect power to the dryer before inspecting or replacing parts.
• Remove the old lint screen, clean the housing, then seat the new screen fully into the slot.
• Clean or replace the screen regularly; inspect the housing for obstructions.
• If you feel resistance or the screen doesn't seat properly, stop and check for foreign objects or damage.

By Frigidaire. Flat, 13" wide, 8" high