Frigidaire Dryer Fuse Or Sensor

• Shuts off too soon
• Too hot
• Takes too long to dry
• No heat or not enough heat

My appliance repair guy checked out the problem, but the stack washer dryer required the contractor to dismantle the cabinet to allow the repair to occur. So i wanted the parts available for the repair, so we would not have to have the dryer pulled apart in a small space for an extended time i ordered the parts on Friday afternoon and they arrived at my home before noon on Saturday! The contractor and the repairman were able to coordinate the repair on Tuesday morning, and though the... Read more

• Shuts off too soon
• Too hot
• Takes too long to dry
• Won't start

Recommendations have fun and a bucket to prevent losing parts. First watch the videos, practice disassemble and reassemble the dryer drum. Make certain you have a good screw driver and spatula from kitchen (could not find my putty knife). Secondly, clean and inspect everything, make sure the motor bearing and belt pulleys are in good condition with little or no play. Third after you have confidently disassembled, vacuum cleaned, inspected all the worn parts, grease the motor and pulley,... Read more

I think I have a lemon of a dryer. I keep having to pay someone to replace my heating element about every year. So I already had the heating element, but I thought I would replace the thermostat and the limiter also. Yes, I am a 46 year old mom, and I replaced all three items. Thank goodness to youtube! Ha! I have ordered from you before and you always send promptly. Thanks! Read more

Replaced control board. Did not need Control Thermistor in my case, but I'm keeping it as backup. Got the Drum Belt just in case it breaks on me since the dryer is aging. To replace control board: Disconnect power and pull dryer away from wall. Take 2 black screws on the back off to remove the top lid. Remove 2 screws on top that hold the control interface on. Remove 2 screws on the bottom backside of the control. Pull out control panel and pull off terminal connections and push to remove... Read more

Replaced exhaust thermal cutoff switch. Sears wanted to charge for a service visit + parts and labor. $17 part, $6 shipping and I received the part the following day. Repair complete in less than an hour at a fraction of the cost. Thanks appliance pros. Read more

• No heat or not enough heat

Being a complete DIY I hate to call some unknown person into my home knowing that just to get them there will cost me more than I will spend for parts that I don't need.After all, they are trying to make a living and by selling me parts that I don't need will increase their profits. I've dealt with APP before and was impressed by their site because I could find both mechanical and electrical drawings for almost everything I have. I looked up my dryer, decided what was probably the problem,... Read more

• Oven is too hot
• Little to no heat when baking

Removed old thermostat and pulled old thermocouple fron oven. ran new thermocouple to oven and put in clip, tistalled new thermostat using 2 phillips head screws, done. Read more

I actually found a post from another brave soul who was willing to try to fix his, and had stated when he put the new limiter switch in, it fixed the problem. Since the whole back of the dryer needs to come off to get to the burner, and the limiter switch is inexpensive it seemed like common sense to take this approach first. After all, you don't put a new engine in your car if all it needs is a new battery! I also found posts that an overheating event could fry the main control board, and... Read more

Simple unscrewed the set screw, removed the broken sensor-moisture part, attached the leads, and reattached the part to the back of the dryer. Took about 4 minutes. Read more

My Electrolux Frigidaire Gas Dryer stopped working and I got an error code E66 that the thermal limiter blew from over heating. The E66 code stops displaying after the initial code and you will then get a door open message. I replaced the thermal limiter and the thermostat just to be sure which part at the problem. The job is hard because you have to take apart the entire dryer and remove the drum. Would be a tough project to complete on your own. Read more

• Too hot

Replaced upper and lower felts. Painted rubbing surface on inside of drum with refrigerator enamel. Took out drum and lubed rear bearing. Replaced 2 of the 3 thermostats, and the belt just on principle. Spent a lot of time with shop-vac removing lint from drier and exhaust ducts. Runs great and is no longer cooking or staining clothes. Read more

Replaced all sensors, limiters, thermistors, thermostat. Works great now. Read more

Fixed it in 5minutes. One end has a Phillips head screw and the other has a tab with to metal leads for wires. The end with the tab broke. I removed the screw for the other end abd the sensor bar came off. To put the new piece on, I connected the wires to the leads, slid the tab end into place on the drum and screwed in the other end. Done! Easy! Read more

I replaced both thermostats, the seals and the heating element and the belt. It's an easy job to keep my dryer last longer. Read more

Yes Read more