Freezer Hinge Parts

This bearing installs in the refrigerator/freezer door hinge to provide a smooth pivot point and maintain alignment. Replacing a worn bearing restores easy door movement and helps the door close and seal correctly.

• Provides a low-friction surface between the hinge pin and hinge bracket for smooth door pivoting
• Helps maintain proper door height and alignment for a reliable gasket seal
• Typical symptoms of wear: squeaking or grinding when opening, door binding or dropping, door not closing fully or popping open
• Excess wear can contribute to air leaks and frost buildup around the door

• Disconnect power before servicing; remove or secure items in the door
• Support the door; remove hinge fasteners and lift the door off if required
• Note and retain any shims/spacers; install the new bearing in the hinge as oriented in the diagram
• Reinstall and align the door; verify smooth operation and a complete gasket seal. Do not lubricate unless specified by the manufacturer

This hinge assembly supports and pivots the appliance door so it opens smoothly and closes squarely against the gasket. Replacing a worn or bent hinge restores alignment and helps maintain a reliable seal and temperature performance. What it does:

• Provides the pivot point and support for the door
• Helps keep the door level for proper gasket contact
• Can help resolve door sagging, rubbing, or binding
• Can help with doors that won't fully close or pop back open
• Addresses play, squeaks, or visible hinge damage

• One hinge assembly

• Disconnect power and support the door before removing hinge fasteners
• Note and transfer any shims/spacers from the old hinge to the new one
• Reuse existing hardware unless the manufacturer specifies otherwise
• After installation, verify door alignment and full gasket contact; adjust as needed

This hinge assembly provides the pivot and support for your freezer door or lid, allowing smooth opening and secure closing. Replacing a worn hinge restores alignment and helps the gasket seal to keep cold air contained.

• Supports and pivots the door/lid during opening and closing
• Maintains alignment so the door/lid closes fully and seals properly
• Can help resolve sagging, binding, scraping noises, or doors not closing all the way
• Replaces a bent, cracked, or seized hinge assembly

• Disconnect power before service; wear gloves.
• Support the door or lid and use a second person to prevent drops or damage.
• Transfer any spacers, bushings, or covers from the old hinge if required.
• Align the hinge, tighten fasteners, and verify smooth operation and gasket seal.

This door hinge restores proper door support and alignment so the appliance door opens and closes smoothly. It replaces a worn or damaged hinge to help keep the door level and sealing correctly. What it does:

• Secures the appliance door to the cabinet and provides a pivot point for opening and closing
• Restores correct door alignment to prevent sagging or rubbing
• Helps maintain a consistent door seal to reduce drafts and temperature loss
• Useful when a door binds, droops, or won't stay closed properly

• One door hinge

• Disconnect power to the appliance before beginning any repair
• Keep original screws and mounting hardware if they are undamaged; replace if worn
• Door may be heavy—have a helper support the door while removing/installing the hinge
• Follow the manufacturer's instructions for proper alignment and torque

This door hinge is the replacement pivot that supports and guides a refrigerator or freezer door for smooth opening and reliable alignment. It restores proper door movement and helps maintain an even seal. What it does

• Provides the pivot point so the appliance door opens and closes smoothly
• Keeps the door aligned to prevent sagging or rubbing
• Helps maintain a proper door seal to reduce temperature loss
• Commonly used when a door drops, drags, or doesn't close evenly

• One (1) door hinge

• Disconnect power to the appliance before starting any repair
• Support the door while removing/installing the hinge to prevent damage or injury
• Use appropriate hand tools; tighten fasteners securely but avoid over-tightening

This bottom hinge replaces the lower door pivot on compatible Frigidaire refrigerators to restore proper door alignment and smooth opening. It provides a secure pivot point to help maintain an even close and consistent seal. What it does:

• Supports and pivots the lower edge of the refrigerator door for smooth opening and closing.
• Helps maintain correct door alignment so the gasket seals evenly.
• Common replacement for doors that sag, bind, or do not close evenly.
• Works with the factory mounting hardware and hinge locations on compatible models.

• Disconnect power and remove food and loose items from the door before starting.
• Always support the door while removing or installing the hinge to prevent injury or damage.
• Use appropriate hand tools and avoid overtightening fasteners; check door alignment after installation.
• Refer to your model's service manual or official parts diagram for model-specific steps and torque specs.

This door hinge secures and allows smooth pivoting of a refrigerator door so it opens and closes correctly. It restores proper door alignment and helps maintain a tight seal to preserve cooling performance. What it does:

• Supports the weight of the door and provides a stable pivot point
• Keeps the door aligned to prevent rubbing, gaps, or uneven closing
• Helps the door seal fully to prevent warm air leaks and temperature loss
• Commonly replaced when the door sags, sticks, or makes noise during operation

• One door hinge assembly

• Disconnect power to the appliance before beginning any repair
• Support the door while removing and installing the hinge to prevent injury or damage
• Use factory mounting hardware; tighten fasteners securely but avoid over-torquing
• Check hinge pins and mounting surfaces for wear

This is the upper case hinge that secures and lets the refrigerator/freezer door pivot smoothly, restoring correct door alignment and sealing. Durable, direct-fit replacement for the refrigerator upper door hinge. What it does

• Supports the top of the door and provides the pivot point for opening and closing
• Keeps the door aligned to maintain a proper seal and even closing
• Replaces a cracked, bent, or worn hinge that can cause door sag or rubbing
• Works with the existing hinge pin and mounting hardware when in good condition

• One upper case hinge

• Unplug the appliance or turn off power before starting work
• Support the door while removing and installing the hinge to prevent drop or damage
• Reuse original screws and hinge pin if undamaged; replace any stripped hardware
• After installation, check door alignment and seal; adjust as needed for even gaps

This door hinge replaces a worn or damaged refrigerator door pivot to restore proper door alignment and sealing. It helps stop sagging, uneven gaps, and doors that stick or don't close fully. What it does

• Provides a stable pivot point so the refrigerator door opens and closes smoothly.
• Restores proper door alignment to improve the magnetic seal and reduce cold air loss.
• Reduces binding, scraping, and rattling associated with worn hinge points.
• Helps correct a door that droops, drags on the cabinet, or sits unevenly.

• One replacement door hinge.

• Unplug the appliance or disconnect power before starting work.
• Support the door while removing hinge fasteners to prevent dropping or damage.
• Use basic hand tools; tighten fasteners securely but do not overtighten.
• Refer to OEM instructions for exact hinge location and torque specs.

This bottom hinge secures and guides the refrigerator/freezer door at the lower pivot, restoring proper door alignment and smooth opening/closing. Durable molded construction matches the original white finish for a clean factory look. What it does:

• Supports the door's lower pivot point to keep the door aligned and balanced
• Allows the door to swing smoothly without binding or dragging
• Helps maintain a proper seal by keeping the door level
• Common replacement when door sags, rubs on the cabinet, or won't close fully

• One bottom hinge (white)

• Unplug the appliance or disconnect power before starting work
• Support the door while removing or installing the hinge to prevent injury or damage
• Typical installation uses basic hand tools; tighten fasteners securely but avoid overtightening
• Check upper hinge adjustment and door leveling

This bottom hinge secures the refrigerator door to the cabinet and provides a smooth pivot for opening and closing. Replaces a worn or damaged hinge to restore proper door alignment and operation. What it does:

• Supports the lower door edge and allows the door to pivot smoothly
• Restores correct door clearance and helps stop sagging or scraping
• Keeps the door sealed by maintaining proper hinge alignment
• Works with factory hinge pins and mounting points for a direct fit

• One bottom hinge as shown

• For safety, unplug the appliance or switch off power to avoid electrical hazards
• Support the door fully before removing the old hinge; use a second person if needed
• Inspect hinge pins and mounting screws; replace any damaged fasteners
• Tighten mounting hardware securely and check door alignment after installation