Parts for Ge GTD45EASJ0WS: Front Panel & Door Parts

This plug button is a replacement cosmetic/functional cap that covers an unused control opening or receptacle on the appliance, restoring a finished appearance and helping keep out dust and debris. What it does:

• Covers and seals an unused control hole or plug location to improve appearance
• Helps prevent dust, lint, and small debris from entering the opening
• Restores a flush, finished look when a switch, knob, or connector is missing
• Simple snap-in design for a clean, low-profile result

• Disconnect power to the appliance before servicing.
• Typically snaps into place; no special tools required for most installations.
• If removal is needed, use a plastic pry tool to avoid scratching surrounding surfaces.
• Your appliance owner's manual or parts diagram to correct placement.

The Lint Filter Assembly is an OEM replacement part for GE dryers. This component is designed to capture lint and other debris generated during the drying process, preventing it from accumulating in the dryer's exhaust system and posing a potential fire hazard.

Symptoms of needing to replace the lint filter assembly include:

• Decreased drying performance or efficiency
• Visible damage, deterioration, or clogging of the filter
• Difficulty in removing or reinstalling the filter assembly

Causes of a faulty lint filter assembly can include normal wear and tear over time, excessive lint buildup or blockage, or physical damage due to mishandling or improper cleaning.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore dryer models.

The Trap Duct Slides are an OEM part for GE dryers. These slides are integral to the dryer's lint trap system, providing a smooth surface for the lint screen to slide in and out easily. This ensures efficient lint trapping and removal.

Replacement of the trap duct slides may be necessary due to wear and tear, damage, or if they become clogged with lint over time. 

Symptoms of a bad Trap Duct Slides include:

• Difficulty in inserting or removing the lint screen.
• Excessive lint accumulation outside the trap area.
• Reduced drying efficiency, possibly due to restricted airflow.
• Visible wear or damage to the slides, hindering the movement of the lint screen.
• Potential for increased risk of overheating if lint is not properly trapped.

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

The Front Drum Support is an OEM part for GE dryers. This component provides critical support to the front of the dryer drum, allowing it to rotate smoothly and maintain proper alignment during the drying cycle. The support does not include bearing slides

A failing drum support can cause the drum to misalign or make unusual noises, leading to potential damage to other components and less effective drying performance.

Symptoms of a bad front drum support include:

• Unusual noises such as squeaking or grinding during operation
• The drum not rotating smoothly or being out of alignment
• Increased wear on the drum or other internal components
• Clothes taking longer to dry or coming out damaged

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Note: 10-watt bulb

The Lamp is an OEM part for GE dryers. This part illuminates the dryer's drum interior, enhancing visibility for loading and unloading garments. It ensures that users can easily see their clothes and any items inside the drum, particularly useful in low-light conditions. 

Replacing a non-functional dryer lamp is important for maintaining the functionality and convenience of your GE dryer, ensuring you can effectively manage your laundry. 

Symptoms of a malfunctioning dryer lamp include:

• A lack of light inside the drum when the dryer door is opened or during operation
• Flickering or intermittent light indicating a loose connection or nearing the end of the lamp's lifespan
• Complete failure to illuminate, which could stem from a burnt-out bulb or electrical issues within the dryer

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

The Bearing Slide Assembly is an OEM component for GE electric clothes dryers. As an integral part of the dryer tumbler system, this assembly includes the bearing slides that allow smooth rotation of the tumbler drum during drying cycles. 

Symptoms of faulty bearing slides include:

• Abnormal vibrations or shaking of the dryer cabinet 
• Noisy operation that gets louder over time
• Rubbing or grinding sounds coming from inside the machine
• Reduced tumbler movement or inability to manually turn the drum

Causes involve general wear of plastic bearing surfaces from years of drum rotation as well as potential damage or misalignment from excess stress on the slides.

This GE OEM replacement helps maintain balanced tumbler movement. Compatible with Hotpoint, RCA, and some Kenmore dryers using the bearing slide assembly design.

The Bearing Top Assembly is an OEM part for GE dryers. This assembly contains the capped metal shafts and roller bearings that smoothly rotate the dryer drum during cycles.

Causes of a bad bearing top assembly include worn or rusted bearings crying out for replacement, bent shafts putting pressure on parts, or detached mounting brackets creating imbalance. Repeated use deteriorates all drivetrain components.

Symptoms of a bad bearing top assembly include:

• Drum unable to tumble or spin as required
• Loud grinding/groaning noises during drying
• Excessive vibrations felt through the machine
• Bearings visibly seized up or shafts noticeably bent

This GE replacement part is compatible with Hotpoint, RCA, and some Kenmore models.

This complete microwave oven door assembly restores the oven's sealed cooking chamber and user access, helping stop heat or steam leaks and providing a secure, functional door surface. Use it to replace a cracked, bent, or non-closing door. What it does:

• Replaces the full microwave door so the oven seals and operates safely
• Restores the outer panel, inner trim and viewing area for normal use
• Helps resolve symptoms like a broken or cracked door, poor closure, rattling, or visible damage
• Re-establishes proper door alignment and latch engagement when installed correctly

• Disconnect power and unplug the appliance before beginning any repair
• Handle glass and trim carefully; wear gloves and eye protection if glass is cracked
• Installation may require removal of surrounding trim or control panel—retain all screws and fasteners

The Dryer Latch is an OEM part for GE dryers that keeps the dryer door securely closed during operation. It provides a secure connection between the door and the dryer cabinet to prevent any accidental openings while the machine is in use.

A bad Dryer Latch can occur due to regular use, wear and tear, or accidental damage. If the latch becomes worn, broken, or fails to engage properly, it can lead to issues such as the door popping open during a drying cycle or the dryer not starting at all.

Symptoms of a bad Dryer Latch include:

• Door not staying closed during a drying cycle.
• Difficulty in latching the door shut.
• Visible damage or deformation of the latch.
• Inability to start the dryer.

Replacing the Dryer Latch with this genuine GE part ensures a secure and reliable closure for your dryer door. This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

The Dryer Door Hinge is an OEM part for GE dryers. It enables the smooth opening and closing of the dryer door, ensuring proper alignment and a secure seal during operation. This hinge is essential for maintaining the functionality and efficiency of the dryer, as well as ensuring safety by keeping the door closed during cycles.

You should replace this door hinge if it becomes defective. Causes of a bad door hinge can include wear and tear from frequent use, rust or corrosion, or damage due to forceful impacts.

Symptoms of a bad door hinge include:

• Difficulty in opening or closing the dryer door
• The door not staying securely closed during operation
• Misalignment of the door, leading to gaps
• Squeaking or grinding noises when the door is moved

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This socket assembly provides a secure electrical connection for the appliance's component, restoring reliable power transfer where a worn or damaged socket prevents operation. It's a direct-fit replacement designed to reinstall using the original wiring and mounting points. What it does:

• Re-establishes a solid electrical connection between the appliance wiring and the component to restore functionality
• Commonly replaces sockets that are cracked, corroded, burned, or loose and cause intermittent operation
• Helps stop arcing, overheating at the terminal, or loss of power to the connected component
• Matches OEM fit and mounting to maintain safe, stable contact under normal use

• One socket assembly

• Disconnect power (unplug or switch off circuit breaker) before starting any repair
• Note wire colors/locations or take a photo before removing old socket to ensure correct reconnection
• Use appropriate tools; avoid crimping or pinching wires—replace any damaged wiring or terminals
• If corrosion, heat damage, or melting is present on surrounding components, inspect and replace affected parts.

This door switch is an OEM replacement part for GE dryers. This switch is designed to promptly end the dryer cycle when the door is opened. The switch comes equipped with a metal lever arm and plunger that can be depressed to activate the switch.

Causes of a bad door switch can include normal wear over time from repetitive open/close cycles. Exposure to moisture, food drips or cleaning chemicals may also contribute to switch failure. 

Symptoms of a bad door switch are:

• The oven will not start a bake cycle with the door securely latched  
• Error codes displayed related to the door being open
• Inconsistent or unreliable door closure sensing  
• Failure to function properly after cleaning or moisture exposure

This OEM part is also compatible with ranges sold under Hotpoint and RCA brands and some Kenmore models. 

A replacement shield switch that helps the oven/microwave detect door position so the unit runs only when the door is closed. Restores reliable door sensing and user safety by replacing a worn or damaged switch. What it does

• Acts as the door-position sensing switch to allow operation only when the door is properly closed
• Stops intermittent or failed start issues caused by a worn or faulty door switch
• Helps correct symptoms like oven/microwave not starting, stopping mid-cycle, or inconsistent door detection
• Works as the plug-in electrical switch used in the door/shield assembly

• Disconnect power at the breaker or unplug the appliance before starting any repair
• Access may require removing the door or control/vent panels
• Handle small metal parts and electrical connectors carefully; avoid bending terminals
• Test door operation and proper function after installation

The Door Strike is an OEM part for GE dryers. It ensures the dryer door securely latches when closed, allowing the dryer to operate properly. The door strike works with the door catch or latch mechanism, creating a tight seal to prevent heat and noise from escaping during the drying cycle.

A bad door strike can lead to issues with the door not closing or staying closed, resulting in poor drying performance and potential safety hazards. Causes of a bad door strike can include wear and tear over time, damage due to accidental impact or mishandling, or a faulty latch assembly.

Symptoms of a bad door strike include:

• Difficulty in closing or latching the dryer door
• Door opening during operation
• Visible signs of damage or wear on the door strike or latch assembly

Replace your worn-out or damaged door strike with this genuine OEM GE part to ensure a secure and reliable closure of your dryer door. 

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This harness high-limit assembly connects the oven/dryer high-limit thermostat to the control system to help protect against overheating. It replaces a damaged or worn high-limit wiring harness to restore proper thermal cutoff signaling. What it does:

• Routes electrical connections between the high-limit thermostat/thermal cutoff and the appliance control
• Allows the high-limit device to open the circuit when temperatures exceed safe limits
• Common symptom: appliance fails to heat or repeatedly trips a thermal cutoff
• Common symptom: visible damaged/frayed wires or loose connector fit at the high-limit

• One high-limit harness assembly as shown

• Disconnect all power (unplug or shut off breaker) before starting service
• Use basic hand tools; ensure connectors are fully seated and insulated

This strike plate mounts at the door opening and works with the door latch/strike to keep the appliance door securely closed during operation. Replacing a worn plate helps restore positive latching and reliable cycle start/stop via the door switch.

• Provides the catch surface for the door latch/strike to engage
• Helps keep the door closed and properly aligned
• Enables the door switch to engage so the cycle can run
• Common symptoms include: door won't stay closed, door pops open, unit won't start unless the door is pressed, visible wear or bending on the plate

• Disconnect power before servicing
• Open the door and remove the screws securing the existing plate
• Align the new plate with the latch/strike and fasten securely with the existing hardware
• Test door closure and latch engagement; adjust alignment if necessary

This metal mounting plate supports the dryer door strike/catch interface. It provides a solid anchor point so the door latches securely, helping the dryer start and run only when the door is properly closed.

• Reinforces the latch area to keep the door securely closed
• May help when the door won't stay shut or the dryer won't start unless the door is held closed
• Useful if the existing plate is bent, loose, or missing
• Helps prevent vibration-related door pops during a cycle

• Unplug the dryer before servicing
• Open the door and remove fasteners securing the old plate; retain hardware if reusable
• Position the new plate and tighten screws evenly—do not overtighten
• Test door closure and latch engagement before restoring power

This replacement screw secures dryer panels and assemblies, helping prevent vibration and keeping components properly aligned. Use it to replace missing or stripped hardware and restore a solid, factory-tight fit during reassembly.

• Secures panels, brackets, and internal assemblies in the dryer cabinet
• Replaces lost, damaged, or stripped factory screw
• Helps reduce vibration and rattling caused by loose hardware
• Supports proper alignment of parts and a tight fit
• Symptoms can include loose or shifting panels, rattling noises, or gaps

• Disconnect power before servicing; for gas dryers, also shut off the gas supply if moving the unit.
• Match screw length and location to the original during reassembly.
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening.
• Use the correct driver for your screw head style as used on your model.

The Shoe Drying Rack is an OEM accessory component specifically designed for select GE dryers. As an added feature, this rack provides a convenient way to dry shoes along with regular laundry items. It allows wet shoes to be tumbled gently while being fully ventilated to dry effectively.

Symptoms of a bad shoe drying rack include:

• Broken or cracked rack supports that collapse the structure
• Missing hooks or attachment points to secure the rack in place  
• Rust, corrosion, or other damage that compromises its functionality

Causes of a bad shoe drying rack can include normal wear and tear over extended use, exposure to excessive heat levels, or damage from overloading or improper handling.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.