Parts for Ge GTD45EASJ0WS: Backsplash, Blower & Motor Assembly Parts

Control knob that mounts on the timer shaft to select drying times and cycles. Replace if cracked, broken, or won't grip the shaft properly. Includes clip.

Rear control console panel for your dryer. Supports and protects user controls and wiring. Replace when original is cracked, warped, or broken to restore fit.

Control panel knob for selecting wash cycles. Replaces broken, cracked, or stripped knobs. Installs on the front panel—simply pull off the old knob.

If your dryer over-dries or under-dries clothes, the dryness control board may have failed. This part monitors moisture levels to adjust drying cycles.

Support plate that mounts behind the dryer console to secure the electronic control board. Replace if cracked, broken, or missing to properly reinstall control.

Dryer won't start when you press the button, or stops when released? The push-to-start switch often fails. Easy 20-minute DIY repair with video.

Rear access panel for dryers. Covers the back of the dryer cabinet and provides access to internal components. Replace if cracked, damaged, or missing.

Secures dryer panels and internal components to the cabinet frame. Replace if screw is stripped, missing, or loose to prevent vibration and rattling.

Replace a cracked, worn, or missing washer in your dryer. This small hardware component ensures proper spacing and tension between parts during operation.

If your dryer won't change heat settings or cycles won't switch properly, this rotary switch restores control selection. Moderate DIY repair.

Fix a dryer dial that won't respond or shifts inconsistently between cycles. This rotary selector switch restores reliable control of settings and cycles.

If your dryer isn't beeping at cycle end or for alerts, this variable buzzer restores audible signals. Direct replacement for clear tone notifications.

Fix a dryer that won't shut off or won't start with a new timer. Controls cycle length and auto-shutoff. Average DIY repair in under 30 minutes.

Factory screw that secures dryer panels, brackets, and internal components. Replace missing, stripped, or damaged screws to restore proper fit and alignment.

Jumper harness for dryers. Connects electrical components within the control system. Replace if worn, damaged, or causing connectivity issues.

This genuine replacement wire harness routes power and signals between a range of appliance's control and electrical components to restore reliable connections and proper operation. What it does:

• Transfers power and control signals between controls, switches, and motors or sensors
• Replaces damaged or frayed wiring that causes intermittent operation or component failure
• Helps resolve symptoms such as no power to a circuit, intermittent function, or unresponsive controls
• Maintains factory routing and connector fit for a secure, vibration-resistant connection

• Disconnect power (unplug or shut off breaker) before starting any repair
• Handle connectors gently; match connector shapes and pin counts before installing
• Route and secure the harness using existing clips or ties to avoid heat or moving-part contact

Fix dryer electrical faults with this orange jumper harness. Routes signals between wiring sections to restore proper connection and component communication.

Jumper harness board for dryers. Connects electrical components on the control panel. Replace if damaged, corroded, or causing connection issues.

The Blower Wheel is an OEM component specifically designed for GE dryers. It is responsible for circulating air during the drying cycle, directing airflow through lint and clothes to remove moisture. The plastic blades of the blower wheel push air through the dryer and out the vent when the motor is running. 

Symptoms of a bad blower wheel include:

• Slow or inefficient drying times even on low moisture loads    
• Strange noises from inside the dryer cabinet      
• Excessive vibrations felt through the dryer door or cabinet
• Bent or cracked blower wheel blades

Causes can include normal wear and tear over time, accidents that damage the blades, or failures in the secure mounting of the blower wheel.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models. 

Secures the drive motor to its mounting bracket. Replace if cracked, broken, or missing to keep the motor and blower aligned and stable during operation.

Secures your dryer motor to the cabinet to reduce vibration and noise. Replace if motor shifts or rattles during operation. Confirm fit with your model.

Metal bracket that secures the dryer motor and blower assembly in place. Replace if your mounting bracket is cracked, broken, or causing loose components.

Transfers power from motor to drum in your dryer. Replace if squeaking, not spinning, or visibly worn. Confirm fit with your model number before ordering.

Supports the idler pulley to maintain proper belt tension in your dryer. Replace if the arm is warped, cracked, or causing belt tracking issues.

Idler pulley for dryer drum assembly. Maintains belt tension to enable smooth drum rotation. Replace if worn, cracked, or causing noise during operation.

Seals the blower-to-exhaust duct connection in your dryer. Replace if torn, brittle, or causing heat loss and longer dry times. Confirm fit by model.

Dryer taking too long or not drying? This blower housing directs airflow from motor to drum. Restores venting and drying performance. Moderate DIY.

Routes hot air from blower to external vent. Replace if cracked or leaking to restore airflow and prevent lint buildup. Confirm fit with model.

Fix a dryer that won't heat properly or overheats with this thermostat. Senses exhaust temperature to regulate heat cycles and prevent damage.

Replacement mounting screw for dryer panels and components. Needed when original screws are stripped, missing, or damaged during repair or maintenance.

This plate motor drives the microwave/oven turntable, keeping the glass tray rotating for even cooking and heating. Replaces a worn or failed motor to restore tray rotation and reduce uneven heating. What it does:

• Turns the glass turntable so food cooks evenly
• Stops rotation or hesitates when motor fails or wears out
• May make buzzing, grinding, or intermittent noises before failing
• Prevents the turntable from rotating if the motor no longer engages

• One replacement plate (turntable) motor

• Disconnect power before servicing to avoid shock; verify unit is fully powered off
• Remove the turntable glass and roller guide to access the motor underneath the oven/microwave floor
• Typical install requires removing interior fasteners and unplugging the motor connector; retain hardware for reassembly

Replace missing or stripped mounting screws in your washer dryer combo. This 12-pack secures panels, components, and internal parts during assembly or repair.

This replacement screw secures appliance panels and internal components per your model's hardware list. Replace lost or stripped screws to keep assemblies tight, reduce vibration and rattles, and maintain proper alignment.

• Fastens brackets, covers, and sheet-metal panels as specified in the parts diagram
• Restores proper fit when an original screw is missing, stripped, or damaged
• Helps eliminate rattling or vibration from loose hardware
• Keeps components safely in place during operation

• Disconnect power to the appliance before servicing
• Match length, head style, and thread to the original; install in the same location/quantity
• Start threads by hand to avoid cross-threading; tighten with the correct driver
• Do not overtighten, especially into plastic or thin sheet metal

Fix a dryer that hums but won't start with this motor drive and pulley assembly. Powers the drum and maintains proper belt tension and alignment.

Replacement start button for dryer control panel. Installs on front console. Needed when original button is cracked, broken, or won't depress properly.

The MOTOR & BLOWER ASSEMBLY is an OEM part for GE dryers. It contains both the drive motor that tumbles the dryer drum as well as the blower motor that circulates air through the heating system. This dual-component assembly works together to simultaneously tumble clothes while pushing heated air into the dryer cylinder.

Causes of a bad motor and blower assembly can include failures of either the drive motor or blower motor. Wiring issues or damaged components internal to the assembly housing can also impact performance.  

Symptoms of a bad motor & blower assembly include:

• The dryer drum not spinning or tumbling clothes
• Inadequate or no airflow through the dryer 
• Dryer not heating or cycles taking excessively long
• Loud buzzing or grinding noises from internal motors

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.