Parts for Ge PTD90EBST0WS: Front Panel & Door Parts

Black plug button that covers unused control openings on your dryer control panel. Replace when cracked, broken, missing, or worn to restore a finished look.

Captures lint and debris during drying to prevent exhaust buildup and fire hazards. Replace when torn, ripped, or damaged. Confirm fit with your model.

Fix a dryer duct trap that won't open smoothly or rattles with replacement trap slides. Restores proper vent access and eliminates binding issues.

This duct trap redirects and contains exhaust from the appliance's ventilation opening to help guide airflow and capture debris before it enters the main ductwork. It's a direct-replacement service part designed to restore proper vent routing and reduce buildup in the duct path. What it does:

• Funnels exhaust from the appliance outlet into the duct system for proper ventilation
• Helps prevent large debris and lint from entering the main duct run
• Restores correct vent alignment and sealing for efficient airflow
• Commonly replaced when damaged, cracked, or allowing exhaust leaks

• One duct trap

• Disconnect power to the appliance before starting any work; if gas is present, follow gas-safety shutoff procedures
• Access may require removing the rear/discharge panel or lowering the appliance; keep track of fasteners
• Inspect adjoining ductwork and seals; replace or reseal with appropriate high-temp duct tape when reinstalling
• Wear gloves and eye protection

Supports the front of the dryer drum for smooth rotation. Replace if drum wobbles, makes noise, or clothes have black marks. Verify fit with your model.

Dryer drum felt top bearing provides smooth drum rotation and reduces friction. Replace when you hear squeaking or grinding noises during operation.

Dryer bearing slides enable smooth drum rotation. Replace when hearing squeaking or rumbling sounds during cycles. Confirm fit with your model number.

The Dryer Bearing Slide (2-Pack) is an OEM replacement part for GE dryers. These slides are installed on the front panel of the dryer and support the drum as it rotates. They help reduce friction and wear, ensuring smooth and quiet operation during drying cycles. This pack includes two bearing slides, which are commonly used together in the dryer assembly.

Over time, bearing slides can wear down due to regular use, heat, and friction. When they become worn or damaged, the drum may no longer rotate smoothly, which can affect the dryer's performance and increase noise levels.

Symptoms of bad dryer bearing slides include:

• A loud squeaking or scraping noise during operation
• Difficulty rotating the drum manually
• Clothes taking longer to dry due to improper drum movement
• Visible wear or thinning on the existing slides

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Supports and rotates the dryer drum smoothly. Replace if you hear screeching noises or notice a gap between drum and front panel. Verify fit with your model.

Wire connector for dryers. Installs in the wiring harness to create secure electrical connections. Replace if connector is damaged, melted, or corroded.

Seals the lint screen housing to prevent lint bypass into internal components. Replace if lint escapes or seal is worn. Confirm fit with your model.

Dryer door pops open during cycle or won't stay closed? Replace the door latch. This part secures the door to the cabinet. Easy 5-minute DIY fix.

This replacement fence is a shelf retainer that helps keep items secure on a refrigerator shelf or door bin, restoring proper containment and organization. It replaces damaged or missing retainers to reduce shifting and spills. What it does:

• Secures items on a shelf or door bin to prevent items from sliding or falling
• Restores proper edge containment after a cracked or broken fence
• Helps maintain organized storage and consistent shelf function
• Common symptom: items sliding off shelf or through the shelf edge when opening/closing

• Disconnect power to the appliance and remove stored items from nearby shelves before starting
• Remove the affected shelf or bin as needed to access the mounting area
• Typically installs by snapping or sliding into existing mounting slots; align and press until fully seated
• If mounting clips or supports are damaged, replace them before installing this fence

Replace your dryer's worn door hinge assembly to restore smooth opening, closing, and proper alignment. Ensures a tight seal and secure door support. Verify fit with your model number.

Restores bright interior illumination in your dryer drum. Replace when light fails, dims, or flickers. Verify fit with your model number before ordering.

Fix a dryer that won't start, keeps running with door open, or stops mid-cycle. This door switch replacement is a common DIY repair taking 15-30 minutes.

A replacement shield switch that helps the oven/microwave detect door position so the unit runs only when the door is closed. Restores reliable door sensing and user safety by replacing a worn or damaged switch. What it does

• Acts as the door-position sensing switch to allow operation only when the door is properly closed
• Stops intermittent or failed start issues caused by a worn or faulty door switch
• Helps correct symptoms like oven/microwave not starting, stopping mid-cycle, or inconsistent door detection
• Works as the plug-in electrical switch used in the door/shield assembly

• Disconnect power at the breaker or unplug the appliance before starting any repair
• Access may require removing the door or control/vent panels
• Handle small metal parts and electrical connectors carefully; avoid bending terminals
• Test door operation and proper function after installation

Left-side drum support bushing for dryers. Installs between drum and rear panel to reduce friction. Replace if worn, cracked, or causing noise.

Right-side drum support bushing for dryers. Installs at the rear drum roller assembly. Replace when worn, cracked, or causing drum wobble or noise.

This is a replacement drain pump assembly that removes wash water from the tub so your washer can complete drain and spin cycles. It restores normal water removal and helps prevent standing water after a wash. What it does

• Pumps water out of the washer during drain and spin cycles
• Helps clear standing water and allows the washer to advance to the spin cycle
• Commonly replaces pumps that hum, do not pump, leak, or make grinding noises
• Can resolve error codes or symptoms related to failure to drain

• One drain pump assembly

• Disconnect power and water supply before beginning any repair
• Drain remaining water from the tub before removing the old pump
• Handle carefully to avoid damaging impeller or housing; check for trapped debris or foreign objects
• If hoses or clamps are worn, consider replacing them at the same time

If your dryer won't start or the door won't latch securely, the door strike may be worn or broken. This part ensures proper door closure. Easy DIY fix.

Dryer won't stop running or clothes come out damp? This sensor harness assembly monitors temperature and moisture levels to optimize drying cycles.

Dryer door won't latch or stay closed? This strike plate mounts at the door opening to catch the latch securely. Easy DIY repair for reliable closing.

Dryer door won't stay closed or pops open during cycle? This mounting plate anchors the door strike for secure latching. Quick DIY fix with video guide.

Secures dryer panels, brackets, and internal assemblies. Replace missing, stripped, or damaged screws to restore proper alignment and prevent vibration.

Steam generator assembly for dryers with steam-refresh cycles. Installs inside cabinet to heat and release steam. Replace if cracked, leaking, or damaged.

Accessory rack that installs inside your dryer drum to safely dry shoes and delicate items. Replace if damaged, broken, or missing from your unit.