Parts for Ge VFD31EDSR0WW: Front Panel & Door Parts

This tapping screw is a self-tapping fastener used to secure panels and components on compatible appliances, restoring secure mounting and preventing loose or vibrating parts. It's a direct replacement for a single factory screw. What it does:

• Threads into sheet metal or plastic mounting points to hold panels, brackets, or small components
• Replaces missing or stripped screws that cause loose panels or rattling
• Helps restore proper alignment and secure connections for controls and covers
• Works where a self-tapping fastener is required instead of a machine screw

• Disconnect power to the appliance before beginning any repair
• Use the correct screwdriver or bit to avoid cam-out and head damage
• Start threading by hand to ensure proper engagement, then tighten until snug — do not over-torque
• Replace only with the exact part to ensure fit and proper fastening

This replacement belt protector bolt secures the dryer belt protector to the cabinet, keeping the belt aligned and shielded during operation. Durable metal construction restores proper routing and helps prevent belt wear or rubbing. What it does

• Fastens the belt protector to the dryer frame to maintain correct belt position.
• Prevents the belt from contacting sharp edges or rubbing against the cabinet.
• Helps reduce noise and premature belt wear caused by a loose protector.
• Small OEM fastener designed to match factory fit and function.

• One belt protector bolt.

• Disconnect power to the appliance before starting any repairs.
• Requires basic hand tools (screwdriver or socket) to remove/install.
• Hand-start threads and tighten securely; avoid over-tightening to prevent stripping.
• Verify belt alignment and protector position before restoring power and testing.

This door window frame replaces the front trim that holds the dryer door glass and restores a finished appearance and secure fit. It helps keep the door sealed and the viewing window properly supported during normal use. What it does

• Secures the dryer door glass in the door opening and keeps the window aligned.
• Restores a proper door seal and helps prevent rattling or glass movement.
• Improves appearance by replacing cracked, warped, or damaged trim.
• Fits the factory door assembly and works with the existing glass and latch hardware.

• High-level swap: remove the dryer door from the hinges, separate door panels if required, and replace the damaged frame.
• Use hand tools and keep small screws and clips organized to avoid loss.
• If the door glass is cracked or damaged, replace it before reinstalling the frame.
• Disconnect power to the dryer before working on the door to avoid injury.

This dryer door hinge cover protects the door hinge area and provides a clean finished appearance. It helps keep lint and debris away from the hinge and restores the dryer door's alignment and fit. What it does:

• Covers and protects the dryer door hinge from dirt and wear
• Prevents lint build-up around the hinge that can impede door movement
• Restores a secure, finished fit when a damaged or missing cover causes rattling or gaps
• Matches OEM shape for correct alignment and smooth door operation

• Remove power to the dryer before beginning any work
• Typically installed with basic hand tools; access may require opening the dryer door or removing a trim piece
• Inspect the hinge and surrounding components for damage while replacing the cover

This dryer door seal replaces the worn or damaged rubber gasket that seals the dryer door to the cabinet, helping maintain proper airflow and heat retention so loads dry more consistently and lint stays inside the dryer. What it does

• Replaces the rubber gasket around the dryer door opening to restore a tight seal.
• Prevents conditioned/hot air from escaping the drum, improving drying performance.
• Helps reduce lint and dust from blowing out around the door.
• Resolves symptoms like longer dry times, noticeable air leaks at the door, or visible gaps around the door edge.

• One (1) dryer door seal.

• Disconnect power (and gas if applicable) before beginning any work.
• Ensure door and surrounding area are clean; remove old seal and any debris from the groove before installing the new gasket.
• Seat the seal lip fully into the door opening groove and confirm correct orientation; some seals align with a top/bottom—match the OEM shape.
• After installation, run a short test cycle to check for leaks.

This caster screw is the replacement fastener that secures an appliance caster or leveling wheel to the cabinet, restoring proper attachment for safe, stable movement. Use it when the original screw is lost, stripped, or damaged. What it does:

• Secures the caster or leveling wheel to the appliance cabinet so the wheel stays firmly attached
• Helps stop wobbling or rocking caused by a loose or missing fastener
• Restores smooth rolling and prevents scraping or catching during movement
• Maintains proper cabinet alignment and load support at the wheel location

• Unplug the appliance and remove contents or secure heavy shelves/drawers before working near casters
• Support the appliance with a jack or blocks to relieve weight from the caster before removing/installing the screw
• Use the correct screwdriver or socket to avoid stripping the head; tighten securely but avoid over-torquing