Parts for Ge VFD31EDSR0WW: Trap Duct Assembly Parts

Secures the power cord strain relief to your dryer chassis. Replaces lost or damaged mounting screws to restore secure cord attachment and reduce stress.

This is a ST3.5 x 12 self-tapping screw designed to secure trim, panels, and small appliance components. It replaces stripped or missing screws to restore proper fit and reduce movement or vibration. What it does:

• Fastens appliance panels, brackets, or trim where ST3.5 x 12 screws are specified
• Helps stop rattling, loose panels, or parts that shift during operation
• Provides a secure threaded hold in thin sheet metal or plastic mounting points
• Matches OEM fit where the WH02X26267 screw is specified

• Use the properly sized Phillips driver to avoid cam-out and head damage
• Start screws straight and apply steady pressure; do not over-torque to prevent stripping
• Wear eye protection when working with small fasteners and sharp edges
• Compare size and thread to ensure a proper match

This power cord fix belt is a small cord-retaining strap that secures the appliance power cord to the cabinet. It helps keep the cord in place to reduce strain on the cord connection and maintain a reliable power connection. What it does:

• Holds the power cord firmly against the appliance frame to prevent tugging on the wiring
• Reduces movement that can loosen or wear the cord connection over time
• Helps prevent intermittent power or connection issues caused by a shifted cord
• Keeps cord routing neat and reduces stress at the plug/body interface

• One power cord fix belt

• Always disconnect power before accessing the cord or electrical panels
• Typically installs behind a rear access panel or at the cord entry point; basic tools may be required
• Position so the cord is secure but not pinched; replace if cracked or brittle

Dryer door gasket creates an airtight seal to maintain proper drying temperature. Replace if torn, cracked, or causing heat loss. Verify fit with your model.

Replace a missing or corroded ground screw to restore proper electrical grounding. Prevents shock hazards and ensures safe appliance operation. Quick fix.

Dryer not heating properly or overheating? The outlet thermistor monitors exhaust temperatures to regulate heat levels and prevent damage. Easy fix.

A standard M10 hex nut used to secure M10-threaded fasteners on compatible appliances. Replaces worn or missing nuts to restore secure connections and reduce rattling or looseness. What it does:

• Secures M10 bolts or studs to hold components together
• Helps eliminate movement that can cause vibration or noise
• Restores proper fit where a damaged or missing nut caused instability
• Used anywhere an M10 nut is specified by the manufacturer

• Use the correct wrench or socket to avoid rounding the nut
• Tighten until secure—follow OEM torque specs when available
• Disconnect power and follow safety instructions when working near electrical components

A small M10 nut with an integrated gasket that secures and seals threaded appliance connections to help prevent leaks and hold fittings tight. Compact replacement for worn or damaged sealing nuts. What it does:

• Provides a sealed threaded connection between hoses or fittings and appliance ports
• Compresses the gasket to prevent water or air leaks at the joint
• Keeps fittings securely fastened to reduce vibration and loosening
• Commonly replaced when threads are corroded, gasket is crushed, or leaks are present

• One M10 nut with bonded gasket

• Disconnect power and shut off water supply before servicing
• Hand-start the nut to avoid cross-threading, then snug with the correct sized wrench
• Inspect mating threads and sealing surface; replace if damaged or corroded
• Test the connection for leaks after reassembly

Fix a noisy or wobbling dryer drum with this drum support shaft. Holds the drum wheel in place for smooth spinning and proper alignment. Simple fix.

Supports the dryer drum and allows smooth rotation. Replace if cracked, worn flat, or causing the drum to wobble. Installs on the axle at rear or front.

A small hex nut used to secure fasteners on appliances, restoring proper thread engagement and helping hold panels or components in place. Replaces a worn or missing nut to prevent loose or rattling parts. What it does:

• Secures a mating bolt or stud to keep panels, trim, or components fastened
• Restores proper thread engagement when an original nut is stripped or lost
• Helps stop vibration-related looseness and rattling noises
• Suitable wherever the OEM called out this specific nut in the parts list

• Turn off and unplug the appliance before accessing internal components
• Use the correct size wrench or socket to avoid rounding the nut
• Replace with the same style and thread engagement length specified by the OEM
• Replace the mating stud or bolt to ensure a secure fit

This flat metal washer provides a stable bearing surface for a fastener, helping distribute load and protect surfaces for reliable appliance assembly. It's a simple hardware replacement that restores proper fastening and reduces wear. What it does:

• Provides a smooth, even surface for nuts or bolts to bear against
• Distributes clamping force to prevent damage to panels or components
• Helps reduce loosening and vibration-related rattles
• Protects mating surfaces from wear and deformation

• Disconnect power and water to the appliance before accessing internal components
• Use appropriate tools; avoid over-tightening which can deform the washer or strip threads
• If corrosion or other damage is present, inspect surrounding fasteners and replace as needed

Captures lint and debris during drying cycles. Replace if torn, clogged, or damaged to maintain efficiency and prevent fire hazards. Verify fit with your model.

The Screw is an OEM part for GE washing machines. Specifically, an #8-32 thread forming screw is used throughout internal assemblies for tightening and securing components. 

Symptoms of needing replacement screw include:

• Stripped, cross-threaded, or severely worn existing screws
• Screw heads sheared or broken off inside fixtures   
• Loosened panels, covers, or parts from backing-out fasteners

Causes involve fatigue, damage, or rusting of individual screws degrading their clamping abilities over extended use cycles.

This GE OEM replacement screw ensures proper compression and attachment of fixtures. Rely on quality fasteners to preserve structural integrity. Order spares and replace problematic screws today before further issues arise from detached or weakened joints.  

Compatible with some Hotpoint, RCA, and Kenmore models, GE #8-32 screws are essential for thorough washer repairs and maintenance.