Parts for Electrolux EFDG317TIW2: Front Panel / Lint Filter Parts

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This duct assembly routes air between internal appliance compartments to maintain proper airflow and temperature. Replacing a damaged duct helps restore even cooling or ventilation and can reduce frost or condensation issues. What it does:

• Channels airflow between components or compartments to support temperature balance and ventilation
• Prevents air leaks that cause uneven temperatures or reduced performance
• Helps reduce frost buildup or excess condensation when airflow is restored
• Stops rattling or vibration caused by cracked or loose ductwork

• Disconnect power to the appliance before beginning any service
• Access may require removing interior panels or trim; keep fasteners organized
• Handle plastic ducts gently to avoid cracks; verify fit and seals before reassembly
• Test the appliance after installation and watch for proper airflow and temperature

This screw is a direct-replacement mounting fastener used to secure appliance panels and internal components, restoring proper fit and reducing vibration or rattling. Simple hardware for repairs that require the correct OEM-style fastener. What it does:

• Secures panels, brackets, or internal components to maintain proper alignment
• Helps stop rattling and vibration caused by loose or missing fasteners
• Matches the original fit and length for reliable reassembly when specified
• Used wherever the appliance's service diagram or manual calls for this screw

• Disconnect power to the appliance before performing service to avoid shock or injury.
• Use the correct screwdriver or bit to avoid stripping the head.
• Start threading by hand, then tighten until snug—do not overtighten to prevent stripping or cracking.
• Replace only with the correct OEM part number when diagrams or manuals specify this screw.

The Lint Filter Kit is an OEM component specifically designed for Frigidaire clothes dryers. This kit includes both the main lint filter that collects lint and debris during the drying cycle, as well as the installed mesh screen filter component. These filters play a crucial role in protecting the dryer by trapping lint and preventing clogs in the ventilation system. 

Causes of a bad lint filter kit include excessive lint buildup that blocks airflow, physical damage to the mesh screen or filter housing, or missing components.

Symptoms of a bad lint filter kit include: 

• Slow or prolonged drying times 
• Excessive noise or vibration during operation
• Reduced airflow and ventilation in the dryer
• Lint accumulating in the ventilation duct

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 
 

Replacement mounting screw that secures panels, brackets or small components in compatible appliances. Installs quickly to replace stripped or missing fasteners and help stop rattling and restore proper alignment. What it does:

• Fastens panels, trim pieces, brackets and other small assemblies to the appliance.
• Replaces stripped, corroded or broken screws that can cause loose parts or vibration noise.
• Helps restore proper alignment of doors, drawers or trim when a missing screw allows movement.
• Small appliance fastener sized for original mounting points—use the OEM screw whenever possible.

• Disconnect power and water before starting any repair.
• Start the screw by hand to avoid cross-threading; use the correct screwdriver or bit.
• Tighten snugly but avoid overtightening to prevent stripped threads or damaged plastic.

This genuine replacement screw secures appliance panels and components so they stay tightly mounted and aligned during normal use. It's a simple, direct fix when a loose or missing screw causes rattling or parts that won't stay in place. What it does:

• Replaces a stripped, damaged, or missing mounting screw used on trim, panels, or brackets
• Restores secure fastening to stop panel vibration, gaps, or rattling noises
• Matches OEM fit and fastening function for proper alignment
• Used where a short machine screw is required for cabinet or component attachment

• One screw

• Use the correct driver size to avoid stripping the head; turn until snug — do not overtighten
• Replace only the exact screw location and type called for in the service guide
• Disconnect power or follow appliance-specific safety steps if working near electrical or moving parts
• Replace all matching fasteners for even support

This insulator is a small foam/trim piece that cushions and thermally isolates appliance panels to help maintain proper airflow and reduce vibration. It preserves fit between cabinet components for quiet, efficient operation. What it does:

• Cushions panels and components to reduce rattling or vibration noise
• Creates a thermal barrier that helps limit heat transfer between parts
• Keeps panels aligned and spaced to prevent rubbing or abrasion
• Worn or missing insulators can cause noise, vibration, or poor panel fit

• One insulator as shown

• Disconnect power before accessing panels or internal components
• Replace only the worn or damaged insulator; trim or adhesive may be needed to position some styles
• Remove surrounding trim or panels as required to reach the mounting location

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

A replacement door gasket that restores a tight seal on the refrigerator door to help maintain consistent internal temperature and reduce energy loss. Replaces damaged, cracked, or flattened seals to improve cooling efficiency and prevent moisture intrusion. What it does:

• Seals the refrigerator door edge to block warm, humid air from entering the cabinet
• Helps stop frost buildup and excess condensation inside the fresh food compartment
• Reduces compressor run time caused by air leaks and poor temperature control
• Restores proper door alignment and contact when the original gasket is worn or torn

• One refrigerator door gasket

• Disconnect power to the appliance before starting any repair
• Remove the old gasket, clean the door flange, then position the new gasket evenly around the door
• Warm the gasket with a hair dryer or allow time to conform for a better seal if needed
• Check the seal around the full perimeter and adjust as necessary; replace screws or retainers only if specified by the OEM

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

The Latch Assembly is an OEM part for Frigidaire dryers that ensures the proper closing and secure latching of your dryer door during operation. It helps keep the dryer door securely closed, preventing any potential safety hazards.

A bad latch assembly can be caused by wear and tear over time, physical damage, or component failure. Signs of a faulty latch assembly include the dryer door not closing properly, the door popping open during the drying cycle, or difficulties in latching the door securely.

Symptoms of a bad latch assembly include:

• Dryer door not closing or latching
• Door opens during the drying cycle
• Difficulty in latching or unlatching the door

Replace your worn-out or damaged dryer latch assembly with this genuine OEM Frigidaire part to restore your dryer. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

The Wire Harness is an OEM replacement part for Frigidaire clothes dryers. It is a complex assembly of insulated wires that transmit electrical signals to various dryer components like motors, heating elements, switches, and controls. 

Symptoms of a bad wire harness include:  

• Intermittent or unreliable operation of dryer functions
• Error codes indicating electrical issues  
• Components like motors or heating elements failing to turn on
• Sparking or melting smells coming from internal wires

Causes can be damaged from repetitive movement inside the dryer cabinet, cracked insulation exposing wires to shorting, or normal wear over many years of use breaking circuits. 

This genuine Frigidaire replacement is compatible also with Electrolux, Gibson, Kelvinator, and select Kenmore dryer models. 

This door switch senses whether the appliance door is closed and signals the controls to run only when it's safe. Replacing a worn or intermittent switch restores dependable starts and proper shutoff when the door opens. What it does:

• Detects door position and allows operation only when the door is fully closed
• Interrupts operation when the door opens for safety
• Common symptoms include: won't start, stops when the door is moved, or "door open" message/error
• Intermittent starts due to worn actuator or internal switch contacts

• 1 door switch

• Disconnect power before servicing
• Access the switch from the front or top panel; release mounting screws or tabs
• Move wires to the new switch one at a time to maintain correct positions, then secure the switch
• Test operation before reassembly

This clip is a hose clamp used in select laundry appliances. It secures a hose connection to prevent leaks and keep water or air moving where it should, helping maintain reliable washer or dryer performance.

• Secures hose to its fitting to prevent leaks or disconnections
• Helps resolve issues like leaking at a hose joint, loose hose, or poor draining/airflow related to a slipped hose
• Durable spring-style clamp designed for repeatable tension
• Commonly used on internal washer or dryer hose connections

• Unplug the appliance and turn off water supply before service
• Have a towel or pan ready for residual water when removing hoses
• Use pliers to compress and slide the clamp; note original clamp position for reassembly
• Inspect hose ends for cracks; replace the hose if damaged before reinstalling the clamp

No.8 pan head `10 - 10b x 0.50 `cr/sq drive

This spacer is a small positioning piece used to maintain the correct gap and alignment between adjoining components, helping prevent rubbing, noise, or uneven operation.

• Maintains proper spacing between parts for smooth, reliable function
• Helps reduce vibration, rattling, or wear from misaligned components
• Commonly needed when a spacer is missing, damaged, or worn
• Symptoms can include noise, looseness, or parts that don't sit flush

• Disconnect power (and shut off water or gas, if applicable) before starting
• Note the spacer's orientation and placement during disassembly
• Replace any damaged fasteners or clips as needed
• Do not overtighten adjacent hardware to avoid deforming the spacer

Replacement shaft that restores proper rotation and alignment for the appliance's moving components. Use this shaft to replace a worn or damaged spindle and help reduce noise, wobble, and interrupted operation. What it does:

• Transfers rotation between connected moving parts so the appliance can operate smoothly.
• Replaces a bent, worn, or broken shaft that can cause vibration or binding.
• Commonly used when the appliance makes unusual noises, vibrates excessively, or stops turning.
• Helps re-establish correct alignment to prevent premature wear of adjacent components.

• Disconnect power before beginning any repair to avoid shock or injury.
• Keep track of fasteners and any spacers/retainers removed during disassembly.
• Basic hand tools are usually required; avoid forcing parts to prevent damage.

This hinge assembly is the mounting cup that secures the refrigerator door hinge to the cabinet, restoring proper alignment so the door opens and closes smoothly and seals correctly. What it does:

• Provides a stable mounting point for the door hinge to keep the door aligned.
• Prevents door sagging and uneven gaps that can cause poor seals or cooling loss.
• Eliminates binding, grinding, or noisy hinge operation when worn or damaged.
• Helps restore smooth opening/closing after worn or cracked hinge supports.

• Unplug the appliance and remove food from the door area before beginning work.
• Support the door while removing hinge fasteners to prevent sudden drops or damage.
• Use hand tools to remove/install mounting hardware; transfer any hinge pins or cams as needed.
• Test door alignment and operation after installation.

The Roller Wheel Assembly is an OEM part for Frigidaire dryers. It is designed to support the dryer drum and facilitate its smooth rotation during the drying cycle. 

Over time, the roller wheel assembly can become worn out or damaged. Causes of a bad roller wheel assembly can include regular wear and tear from continuous use, accumulation of lint and debris, or damage from overloading the dryer. These factors can lead to the rollers becoming worn or misaligned, affecting the dryer's operation.

Symptoms of a bad roller wheel assembly include:

• Squeaking or thumping noises during the drying cycle
• The drum not rotating smoothly or being off-balance
• Increased drying times due to inefficient drum movement
• Visible wear or damage to the rollers

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Replacement metal mounting nut that secures panels, brackets or small assemblies on Frigidaire appliances. Restores a secure fastening point to reduce wobble, rattling or parts that feel loose or shift during use. What it does:

• Threads onto the matching stud or bolt to hold panels, trim or brackets in place
• Keeps components aligned and prevents movement or vibration
• Helps stop rattling, loose control panels, or parts that pull away from the cabinet
• Simple hardware solution when a corroded or missing nut causes a loose connection

• Disconnect power (or unplug) before accessing internal panels or assemblies
• Use the correct-size wrench or socket; turn clockwise to tighten, counterclockwise to loosen
• Tighten securely but avoid overtightening to prevent thread damage or stripped studs
• If threads are damaged or stud is bent, replace the damaged stud/fastener

The Door Gasket is an OEM part for Frigidaire dryers. This part allows a tight seal around the dryer door, preventing hot air from escaping and cold air from entering during the drying process. 

Causes of a bad door gasket can include normal wear and tear, exposure to extreme temperatures, or accidental damage during loading and unloading of laundry. 

Symptoms of a bad Door Gasket include:

• Clothes taking longer than usual to dry.
• Heat escaping from the edges of the dryer door.
• Visible wear or tears in the gasket material.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement screw secures appliance panels and internal components. A fresh fastener helps keep assemblies tight and aligned, reducing rattles and vibration so parts stay properly mounted during everyday use.

• Fastens panels, brackets, and assemblies to the appliance frame
• Replaces missing, stripped, or corroded hardware
• Helps reduce vibration, rattling, and loose-fitting components
• Symptoms of a bad/missing screw: loose or noisy panel, component won't stay attached, stripped head/threads

• Disconnect power before servicing; turn off water supply if working on a washer
• Replace one screw at a time to maintain alignment and track locations
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Tighten snugly—do not overtighten to prevent stripping threads or heads

Color: Gray

The Door Glass is an OEM part for Frigidaire dryers. It forms an integral part of the dryer door, providing a see-through window that allows users to monitor their laundry during the drying cycle. This high-quality glass is designed to withstand the high temperatures and humidity typical of a dryer environment, ensuring durability and safety without sacrificing functionality.

Causes of a bad Door Glass can include accidental impacts, thermal stress fractures, or general wear and tear, which can lead to cracks or shattering of the glass.

Symptoms of a faulty Door Glass include:

• Visible cracks or breaks in the glass.
• Loose glass that may compromise the door's seal.
• Excessive condensation within the door due to a breach in the glass integrity.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Outer Window is an OEM part for Frigidaire dryers. This part provides a clear view into the dryer while it operates. It allows you to monitor your laundry during the drying cycle without opening the door, which helps maintain the efficiency and effectiveness of the dryer by keeping the heat contained.

Causes of a bad outer window can include accidental impacts, general wear and tear, or degradation from the high heat environment inside the dryer. 

Symptoms of a bad outer window include:

• Cracks or breaks in the window that can compromise the insulation of the dryer.
• Scratches or cloudiness that obstruct visibility into the dryer.
• Loose fitting that may affect the door's ability to close properly.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This striker is the metal catch the refrigerator door latch engages to keep the door closed. Replacing a worn or broken striker restores proper door engagement for a tighter seal and more consistent cooling. What it does:

• Provides the catch point for the door latch so the door stays securely closed
• Ensures correct door alignment to help maintain the gasket seal and prevent cold-air loss
• Stops door from popping open or shifting while opening/closing
• Helps reduce noise from a misaligned latch and prevents excessive wear on the latch assembly

• Unplug the appliance or shut off power to the unit before beginning any repair
• Replacement typically requires basic hand tools (screwdriver or nut driver) to remove and install mounting fasteners
• Align striker with the latch, tighten fasteners securely, then test door operation and adjust as needed
• If the door gasket is damaged or the latch is bent, inspect and replace those parts as required for a complete repair

The High Temperature Adhesive is an OEM part for Frigidaire appliances. This adhesive is specifically formulated to withstand high temperatures and is used in various repair applications within appliances such as ovens, ranges, and dryers.The 1-ounce tube contains adhesive formulated to withstand the extreme heat inside dryer drums and cabinets

Causes of a bad adhesive can include exposure to extremely high temperatures over extended periods, contamination by dirt or grease, or the natural aging and drying out of the adhesive.

Symptoms of a bad high temperature adhesive include:

• Components or parts becoming loose or detached
• The adhesive becoming brittle or cracked
• Inability to properly bond surfaces exposed to high heat
• Visible deterioration or peeling of the adhesive

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.