Parts for Electrolux EFME527UIW0: Front Panel / Lint Filter Parts

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

The Duct Assembly is an OEM part for Frigidaire dryers. This part channels hot air and moisture from the dryer drum to the outside vent. 

Causes of a bad duct assembly can include blockages from lint buildup, physical damage that can restrict airflow, or deterioration over time due to heat and moisture exposure. 

Symptoms of a bad duct assembly include:

• Reduced drying efficiency, with clothes remaining damp after a cycle
• Excessive heat buildup within the dryer
• Unusual noises from the dryer suggesting airflow restriction
• Accumulation of lint within the dryer, indicating poor expulsion of air and debris

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This screw is a direct-replacement mounting fastener used to secure appliance panels and internal components, restoring proper fit and reducing vibration or rattling. Simple hardware for repairs that require the correct OEM-style fastener. What it does:

• Secures panels, brackets, or internal components to maintain proper alignment
• Helps stop rattling and vibration caused by loose or missing fasteners
• Matches the original fit and length for reliable reassembly when specified
• Used wherever the appliance's service diagram or manual calls for this screw

• Disconnect power to the appliance before performing service to avoid shock or injury.
• Use the correct screwdriver or bit to avoid stripping the head.
• Start threading by hand, then tighten until snug—do not overtighten to prevent stripping or cracking.
• Replace only with the correct OEM part number when diagrams or manuals specify this screw.

The Lint Filter Kit is an OEM part compatible with Frigidaire electric dryers. This kit includes both a lint filter screen and housing assembly. 

Causes of a bad lint filter include blockages from excess lint that the filter cannot effectively remove. Small tears or openings in the filter mesh can also bypass lint rather than capture it.

Symptoms of a clogged or damaged lint filter include: 

• Slow or incomplete drying times  
• Excessive moisture left in clothes after a full cycle
• Reduced airflow noticed around the lint filter area
• Visible lint buildup inside the dryer cabinet

This OEM replacement is compatible with Frigidaire, Electrolux, Gibson, Kelvinator and some Kenmore dryers for a direct fit solution.

Replacement mounting screw that secures panels, brackets or small components in compatible appliances. Installs quickly to replace stripped or missing fasteners and help stop rattling and restore proper alignment. What it does:

• Fastens panels, trim pieces, brackets and other small assemblies to the appliance.
• Replaces stripped, corroded or broken screws that can cause loose parts or vibration noise.
• Helps restore proper alignment of doors, drawers or trim when a missing screw allows movement.
• Small appliance fastener sized for original mounting points—use the OEM screw whenever possible.

• Disconnect power and water before starting any repair.
• Start the screw by hand to avoid cross-threading; use the correct screwdriver or bit.
• Tighten snugly but avoid overtightening to prevent stripped threads or damaged plastic.

This genuine replacement screw secures appliance panels and components so they stay tightly mounted and aligned during normal use. It's a simple, direct fix when a loose or missing screw causes rattling or parts that won't stay in place. What it does:

• Replaces a stripped, damaged, or missing mounting screw used on trim, panels, or brackets
• Restores secure fastening to stop panel vibration, gaps, or rattling noises
• Matches OEM fit and fastening function for proper alignment
• Used where a short machine screw is required for cabinet or component attachment

• One screw

• Use the correct driver size to avoid stripping the head; turn until snug — do not overtighten
• Replace only the exact screw location and type called for in the service guide
• Disconnect power or follow appliance-specific safety steps if working near electrical or moving parts
• Replace all matching fasteners for even support

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

A replacement door gasket that restores a tight seal on the refrigerator door to help maintain consistent internal temperature and reduce energy loss. Replaces damaged, cracked, or flattened seals to improve cooling efficiency and prevent moisture intrusion. What it does:

• Seals the refrigerator door edge to block warm, humid air from entering the cabinet
• Helps stop frost buildup and excess condensation inside the fresh food compartment
• Reduces compressor run time caused by air leaks and poor temperature control
• Restores proper door alignment and contact when the original gasket is worn or torn

• One refrigerator door gasket

• Disconnect power to the appliance before starting any repair
• Remove the old gasket, clean the door flange, then position the new gasket evenly around the door
• Warm the gasket with a hair dryer or allow time to conform for a better seal if needed
• Check the seal around the full perimeter and adjust as necessary; replace screws or retainers only if specified by the OEM

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

The Latch Assembly is an OEM part for Frigidaire dryers that ensures the proper closing and secure latching of your dryer door during operation. It helps keep the dryer door securely closed, preventing any potential safety hazards.

A bad latch assembly can be caused by wear and tear over time, physical damage, or component failure. Signs of a faulty latch assembly include the dryer door not closing properly, the door popping open during the drying cycle, or difficulties in latching the door securely.

Symptoms of a bad latch assembly include:

• Dryer door not closing or latching
• Door opens during the drying cycle
• Difficulty in latching or unlatching the door

Replace your worn-out or damaged dryer latch assembly with this genuine OEM Frigidaire part to restore your dryer. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

The Wire Harness is an OEM replacement part for Frigidaire clothes dryers. It is a complex assembly of insulated wires that transmit electrical signals to various dryer components like motors, heating elements, switches, and controls. 

Symptoms of a bad wire harness include:  

• Intermittent or unreliable operation of dryer functions
• Error codes indicating electrical issues  
• Components like motors or heating elements failing to turn on
• Sparking or melting smells coming from internal wires

Causes can be damaged from repetitive movement inside the dryer cabinet, cracked insulation exposing wires to shorting, or normal wear over many years of use breaking circuits. 

This genuine Frigidaire replacement is compatible also with Electrolux, Gibson, Kelvinator, and select Kenmore dryer models. 

The Switch is an OEM component specifically designed for Frigidaire dryers. It plays an important control function to safely operate tumble and heat functions. 

The switch allows for fingertip selection of machine settings. It enables tailored drying based on fabric load conditions. Precise control helps prevent over-drying for optimal care. 

Causes of switch failure can include repeated pressing over many cycles leading to natural wear of internal contacts. Spills or debris accumulation may also cause issues.

Symptoms of a bad switch include: 

• Failure to start or inability to select desired options  
• Unintended stopping mid-cycle
• Lack of response when touching selector buttons

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore dryer models. Replacement restores easy operation.
 

The Door Switch is an OEM part for Frigidaire clothes dryers. It is an electronic component located on the door frame that detects when the dryer door is latched closed. The switch communicates this information to the control board, allowing the dryer to operate properly by preventing operation if the door is open.

Causes of a bad door switch can include normal wear and tear from opening and closing the dryer door over time. Physical damage from accidental impacts or overtightening of door mounting hardware may also cause switch failure.

Symptoms of a bad dryer door switch include:

• The dryer starting a cycle even when the door is open
• Error codes or failure to start/run if the door switch does not detect proper closure
• Other control issues related to incorrectly sensing door position

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Lint Filter Kit is an OEM part compatible with Frigidaire electric dryers. This kit includes both a lint filter screen and housing assembly. 

Causes of a bad lint filter include blockages from excess lint that the filter cannot effectively remove. Small tears or openings in the filter mesh can also bypass lint rather than capture it.

Symptoms of a clogged or damaged lint filter include: 

• Slow or incomplete drying times  
• Excessive moisture left in clothes after a full cycle
• Reduced airflow noticed around the lint filter area
• Visible lint buildup inside the dryer cabinet

This OEM replacement is compatible with Frigidaire, Electrolux, Gibson, Kelvinator and some Kenmore dryers for a direct fit solution.

This clip is a hose clamp used in select laundry appliances. It secures a hose connection to prevent leaks and keep water or air moving where it should, helping maintain reliable washer or dryer performance.

• Secures hose to its fitting to prevent leaks or disconnections
• Helps resolve issues like leaking at a hose joint, loose hose, or poor draining/airflow related to a slipped hose
• Durable spring-style clamp designed for repeatable tension
• Commonly used on internal washer or dryer hose connections

• Unplug the appliance and turn off water supply before service
• Have a towel or pan ready for residual water when removing hoses
• Use pliers to compress and slide the clamp; note original clamp position for reassembly
• Inspect hose ends for cracks; replace the hose if damaged before reinstalling the clamp

No.8 pan head `10 - 10b x 0.50 `cr/sq drive

This hinge assembly is the mounting cup that secures the refrigerator door hinge to the cabinet, restoring proper alignment so the door opens and closes smoothly and seals correctly. What it does:

• Provides a stable mounting point for the door hinge to keep the door aligned.
• Prevents door sagging and uneven gaps that can cause poor seals or cooling loss.
• Eliminates binding, grinding, or noisy hinge operation when worn or damaged.
• Helps restore smooth opening/closing after worn or cracked hinge supports.

• Unplug the appliance and remove food from the door area before beginning work.
• Support the door while removing hinge fasteners to prevent sudden drops or damage.
• Use hand tools to remove/install mounting hardware; transfer any hinge pins or cams as needed.
• Test door alignment and operation after installation.

The Support Roller Washer is an OEM part for Frigidaire dryers, designed to ensure the smooth and stable operation of the dryer drum. Positioned between the support roller and the shaft, this washer plays a critical role in reducing friction and wear, allowing the drum to rotate smoothly and quietly.

Causes of these symptoms often stem from normal wear and tear, which can lead to the degradation of the washer over time.  

Symptoms of a bad Dryer Support Roller Washer include:

• Unusual noises, such as squeaking or grinding, indicating increased friction during drum rotation
• The dryer drum appears to wobble or is misaligned during operation
• Increased vibration of the dryer, which can lead to wear on other components

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Roller Assembly is an OEM replacement part specific to Frigidaire-brand clothes dryers. It contains multiple smooth-rolling cylinders that guide the dryer drum assembly as it turns. 

Symptoms of a faulty dryer roller assembly include: 

• Noisy or rumbling sounds from the dryer cabinet during cycles 
• Vibrating of the dryer body instead of steady drum rotation
• Physical signs like cracked rollers or worn tracks that hold them  

Causes can be seized or corroded rollers failing to spin freely. Dented tracks prevent proper alignment. Over decades, components have worn down from continuous operation.

The part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This OEM fastener replaces a worn, stripped, or missing nut to securely hold components in place inside compatible laundry appliances. Restores proper clamping force to reduce vibration, rattling, and loosening during operation. What it does:

• Secures a mating bolt or stud to keep brackets, panels, or rotating parts firmly mounted
• Restores proper tension after the original nut is lost, corroded, or damaged
• Helps address symptoms like excessive vibration, rattling, or loose assemblies
• Maintains a tight connection in high-vibration environments when properly tightened

• 1 nut

• Disconnect power (and water to a washer) before servicing
• Support the component being fastened; hold the bolt head while loosening/tightening the nut
• Start threads by hand to avoid cross-threading; tighten to manufacturer guidance
• Replace any damaged bolts or hardware it mates with for a secure repair

The Door Gasket is an OEM part for Frigidaire dryers. This part allows a tight seal around the dryer door, preventing hot air from escaping and cold air from entering during the drying process. 

Causes of a bad door gasket can include normal wear and tear, exposure to extreme temperatures, or accidental damage during loading and unloading of laundry. 

Symptoms of a bad Door Gasket include:

• Clothes taking longer than usual to dry.
• Heat escaping from the edges of the dryer door.
• Visible wear or tears in the gasket material.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement screw secures appliance panels and internal components. A fresh fastener helps keep assemblies tight and aligned, reducing rattles and vibration so parts stay properly mounted during everyday use.

• Fastens panels, brackets, and assemblies to the appliance frame
• Replaces missing, stripped, or corroded hardware
• Helps reduce vibration, rattling, and loose-fitting components
• Symptoms of a bad/missing screw: loose or noisy panel, component won't stay attached, stripped head/threads

• Disconnect power before servicing; turn off water supply if working on a washer
• Replace one screw at a time to maintain alignment and track locations
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Tighten snugly—do not overtighten to prevent stripping threads or heads

Color: Black

The Door Glass is an OEM part for Frigidaire dryers. It forms an integral part of the dryer door, providing a see-through window that allows users to monitor their laundry during the drying cycle. This high-quality glass is designed to withstand the high temperatures and humidity typical of a dryer environment, ensuring durability and safety without sacrificing functionality.

Causes of a bad Door Glass can include accidental impacts, thermal stress fractures, or general wear and tear, which can lead to cracks or shattering of the glass.

Symptoms of a faulty Door Glass include:

• Visible cracks or breaks in the glass.
• Loose glass that may compromise the door's seal.
• Excessive condensation within the door due to a breach in the glass integrity.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Outer Window is an OEM part for Frigidaire dryers. This part provides a clear view into the dryer while it operates. It allows you to monitor your laundry during the drying cycle without opening the door, which helps maintain the efficiency and effectiveness of the dryer by keeping the heat contained.

Causes of a bad outer window can include accidental impacts, general wear and tear, or degradation from the high heat environment inside the dryer. 

Symptoms of a bad outer window include:

• Cracks or breaks in the window that can compromise the insulation of the dryer.
• Scratches or cloudiness that obstruct visibility into the dryer.
• Loose fitting that may affect the door's ability to close properly.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Lamp Assembly is an OEM part for Frigidaire dryers. It provides illumination inside the dryer drum during operation, allowing you to easily see the contents inside.

A bad lamp assembly can be caused by a burnt-out bulb, a faulty socket, or electrical issues. Signs of a faulty lamp assembly include a dark interior drum, flickering or intermittent lighting, or a completely non-functional light.

Symptoms of a bad lamp assembly can include:

• A dark interior drum
• Flickering or intermittent lighting

Replace your malfunctioning lamp assembly with this genuine OEM part to restore lighting inside your dryer. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This replacement door gasket creates a tight seal around the refrigerator door to help maintain interior temperature and reduce energy loss. It restores proper sealing for fresher food and more efficient cooling. What it does

• Seals the refrigerator door edge to prevent warm air leaks and frost buildup
• Helps maintain consistent internal temperatures for food safety
• Reduces compressor runtime by improving insulation performance
• Commonly replaced when the seal is cracked, torn, warped, or no longer holds suction

• One refrigerator door gasket

• Inspect the door frame and mounting channel; clean mounting surface before installing the gasket
• Warm the gasket if needed for easier fitting and proper molding to the door
• Do not use the appliance until the new gasket is fully seated and the door seals correctly

This retainer is a small fastener that secures a component inside your appliance, keeping it correctly positioned during operation. Replacing a damaged or missing retainer helps eliminate looseness and noise while preventing wear from parts shifting.

• Holds a mating part or assembly firmly in place
• Restores proper fit when the original retainer is cracked, warped, or missing
• Common symptoms: loose or misaligned parts, rattling/vibration, rubbing noises
• Helps prevent premature wear from movement or chafing

• Disconnect power; shut off gas and water supplies if applicable
• Use your model's diagram to locate the retainer and match its orientation
• Transfer any reusable hardware and ensure the retainer is fully seated
• Reassemble and run a short test to check for proper operation

The High Temperature Adhesive is an OEM part for Frigidaire appliances. This adhesive is specifically formulated to withstand high temperatures and is used in various repair applications within appliances such as ovens, ranges, and dryers.The 1-ounce tube contains adhesive formulated to withstand the extreme heat inside dryer drums and cabinets

Causes of a bad adhesive can include exposure to extremely high temperatures over extended periods, contamination by dirt or grease, or the natural aging and drying out of the adhesive.

Symptoms of a bad high temperature adhesive include:

• Components or parts becoming loose or detached
• The adhesive becoming brittle or cracked
• Inability to properly bond surfaces exposed to high heat
• Visible deterioration or peeling of the adhesive

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.