Parts for Electrolux EIMED6CJIW4: 03 - Front Panel / Lint Filter Parts

This door gasket is the flexible sealing strip that helps keep cold air inside your refrigerator, improving temperature stability and efficiency. It replaces worn or torn seals to reduce drafts and moisture intrusion. What it does:

• Creates an airtight seal around the refrigerator door to help maintain proper internal temperature
• Helps prevent frost buildup and condensation by keeping warm, humid air out
• Reduces energy waste caused by cool-air leaks around the door
• Can fix common symptoms like warm spots near the door, excessive frost, or an overworking compressor

• High-level replacement: usually removed from the door channel and pressed into place; may require loosening door hinges for full removal on some models
• Check that the gasket sits evenly in the channel and that the door closes flush to ensure a proper seal
• Clean the door channel and mating surface before installing to ensure good adhesion and sealing

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Mounting bracket for dryer assemblies. Secures components in place during operation. Replace if bracket is bent, cracked, broken, or missing.

Mounting bracket for dryer installation. Secures components in place. Replace if bent, cracked, broken, or missing to restore proper support and fitment.

Replacement outer housing cover for dryers. Restores finished appearance and shields internal components. Needed when original is cracked or damaged.

Secures and supports your dryer door, allowing smooth opening and closing. Replace if cracked, bent, or broken to restore proper door alignment and function.

Genuine screw fastener for securing dryer panels, brackets, and internal components. Replace when stripped, missing, or corroded to restore tight fit.

Foam insulator strip that cushions dryer panels and reduces vibration. Replace if worn, compressed, or missing to maintain quiet operation and fit.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Replacement fastener screw for dryers, washers, and laundry centers. Secures panels, brackets, and assemblies to the appliance frame. Needed when missing.

Dryer gasket seals the drum to prevent air leaks and maintain proper drying efficiency. Replace if torn, cracked, or causing noise. Verify fit with your model.

Dryer door won't stay closed or pops open during cycle? This door latch secures the door shut. Simple DIY fix in under 5 minutes with a screwdriver.

This door switch senses whether the appliance door is closed and signals the controls to run only when it's safe. Replacing a worn or intermittent switch restores dependable starts and proper shutoff when the door opens. What it does:

• Detects door position and allows operation only when the door is fully closed
• Interrupts operation when the door opens for safety
• Common symptoms include: won't start, stops when the door is moved, or "door open" message/error
• Intermittent starts due to worn actuator or internal switch contacts

• 1 door switch

• Disconnect power before servicing
• Access the switch from the front or top panel; release mounting screws or tabs
• Move wires to the new switch one at a time to maintain correct positions, then secure the switch
• Test operation before reassembly

This is a genuine replacement screw used to secure appliance panels and components. It provides a simple, reliable fix for loose or missing fasteners so panels and parts stay properly attached. What it does:

• Fastens panels, brackets, or components in place to restore original fit
• Replaces missing or stripped screws that cause rattling or loose parts
• Matches OEM thread and head style for correct seating and torque
• Helps eliminate vibration-related noise by securing loose pieces

• One replacement screw as shown

• Inspect mating threads and clear any debris before installing the new screw
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; avoid over-torquing which can damage threads or parts
• Disconnect power and follow appliance safety guidelines before servicing

This line noise filter conditions incoming AC power by reducing electromagnetic interference before it reaches the appliance's electronics. Replacing a shorted or damaged filter can restore stable operation and help prevent erratic control behavior.

• Filters EMI/RFI on the power line before it reaches the control system
• Helps protect sensitive electronics from interference and voltage spikes
• Failure may present as no power, intermittent resets, or nuisance GFCI/breaker trips
• Typically mounted near the power-cord entry; also called a line filter

• Disconnect power and allow any capacitors to discharge before servicing
• Note wire positions and line vs. load orientation; take a photo before removal
• Secure the ground and mount the new filter firmly to the chassis
• Route and reconnect wires carefully to avoid pinching; reassemble and test

Secures hose connections in dryers to prevent leaks and maintain proper airflow. Replace if hoses are loose or disconnected. Verify fit with model.

Washer that fits between the support roller and shaft in your dryer. Replace if worn, cracked, or missing to maintain proper drum alignment and support.

Supports and guides the dryer drum as it rotates. Replace if the roller is cracked, worn, or causing noise. Sold individually, not pre-assembled.

Replacement nut that secures internal components in dryers. Restores clamping force when original nut is stripped, worn, or missing. Prevents loosening.

Front bulkhead for dryer drum assembly. Replaces cracked, broken, or worn bulkheads. Essential structural component for proper drum support.

This trim ring is a replacement surface trim piece that restores the finished look and edge around the appliance opening. It provides a clean, secure edge and replaces bent, cracked, or missing trim to improve appearance and fit. What it does

• Covers and finishes the exposed edge of the appliance opening for a clean appearance
• Secures and aligns adjacent components by providing a stable mounting edge
• Addresses cosmetic damage such as dents, cracks, or paint loss around the opening
• Helps prevent small items from getting caught in the exposed edge

• One trim ring

• Disconnect power to the appliance before starting any repair
• Removal typically requires loosening mounting screws or clips; keep hardware for re-use unless damaged
• Handle edges carefully; part and surrounding metal may be sharp
• If the trim mounts to or around other components (elements, panels), support those parts during removal and reinstallation

Replacement cap or cover for your dryer. Installs on the exterior or interior housing. Order a new cover if yours is cracked, broken, or missing.

Secures dryer panels and components to maintain proper alignment and stability. Replace when the original clip is broken, loose, or missing.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

Fix a dryer door that pops open during the cycle with this door latch striker. Restores secure door engagement. Takes under 5 minutes to install.

This inner oven door glass panel replaces damaged or broken oven door glass to restore safe viewing and help the door seal properly. It's the interior glass used behind the outer door for protection and visibility. What it does:

• Replaces cracked, chipped, or shattered inner oven door glass
• Restores clear view into the oven cavity for safe cooking checks
• Helps maintain the oven door's sealing surface and inner insulation
• Prevents loose glass pieces from falling into the oven cavity

• Wear cut-resistant gloves and eye protection; broken glass is sharp
• Remove the oven door per the manufacturer's instructions before disassembly
• Handle with care to avoid scratches or chipping the edges
• Keep track of all fasteners and orientations for reassembly

Replaces a cracked, scratched, or cloudy outer door lens. This clear plastic panel forms the exterior of your dryer's door window for visibility into the drum.

Replacement access panel cover for dryers and laundry centers. Shields internal components from dust and debris. Replaces cracked, broken, or missing panels.

Fastens panels, brackets, and internal components in your dryer. Replace stripped, rusted, or missing screws to restore secure mounting and alignment.

Restores interior drum lighting when your dryer bulb burns out or fails. Direct-fit LED lamp assembly improves visibility. Verify fit with model number.

Electrical wire harness for dryers. Replaces damaged, frayed, or worn internal wiring connections. Essential when harness is broken or corroded.

Secures components inside your dryer to prevent shifting during operation. Replace this retainer if it's damaged, missing, or broken to eliminate noise.

M5 x 0.8 metric machine screw secures panels and internal assemblies. Replace missing, stripped, or damaged fasteners to restore tight fit.

The High Temperature Adhesive is an OEM part for Frigidaire appliances. This adhesive is specifically formulated to withstand high temperatures and is used in various repair applications within appliances such as ovens, ranges, and dryers.The 1-ounce tube contains adhesive formulated to withstand the extreme heat inside dryer drums and cabinets

Causes of a bad adhesive can include exposure to extremely high temperatures over extended periods, contamination by dirt or grease, or the natural aging and drying out of the adhesive.

Symptoms of a bad high temperature adhesive include:

• Components or parts becoming loose or detached
• The adhesive becoming brittle or cracked
• Inability to properly bond surfaces exposed to high heat
• Visible deterioration or peeling of the adhesive

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.