Parts for Kenmore 417.91102003 (41791102003, 417 91102003): Front Panel / Lint Filter Parts

This door gasket is the flexible sealing strip that helps keep cold air inside your refrigerator, improving temperature stability and efficiency. It replaces worn or torn seals to reduce drafts and moisture intrusion. What it does:

• Creates an airtight seal around the refrigerator door to help maintain proper internal temperature
• Helps prevent frost buildup and condensation by keeping warm, humid air out
• Reduces energy waste caused by cool-air leaks around the door
• Can fix common symptoms like warm spots near the door, excessive frost, or an overworking compressor

• High-level replacement: usually removed from the door channel and pressed into place; may require loosening door hinges for full removal on some models
• Check that the gasket sits evenly in the channel and that the door closes flush to ensure a proper seal
• Clean the door channel and mating surface before installing to ensure good adhesion and sealing

This 38-inch stacking kit lets you securely mount a dryer on top of a matching washer to save floor space and stabilize the stacked units. It provides a tidy, secure connection for paired laundry appliances. What it does:

• Secures the dryer to the washer to reduce the risk of tipping or shifting during operation
• Keeps stacked appliances aligned for safer, more stable operation
• Helps minimize vibration transfer between machines for quieter performance
• Enables space-saving stacked installation in closets or compact laundry areas

• Follow the washer and dryer installation manuals and the kit instructions exactly for proper fit and safety
• Disconnect power and gas (if applicable) and empty both appliances before installing
• Installation may require two people and basic hand tools for safe handling of appliances

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

M5 x 0.8 metric machine screw secures panels and internal assemblies. Replace missing, stripped, or damaged fasteners to restore tight fit.

Foam insulator strip that cushions dryer panels and reduces vibration. Replace if worn, compressed, or missing to maintain quiet operation and fit.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Seals the dryer door to contain heat and prevent air leaks. Replace if torn, cracked, or causing poor drying performance. Confirm fit with your model.

The High Temperature Adhesive is an OEM part for Frigidaire appliances. This adhesive is specifically formulated to withstand high temperatures and is used in various repair applications within appliances such as ovens, ranges, and dryers.The 1-ounce tube contains adhesive formulated to withstand the extreme heat inside dryer drums and cabinets

Causes of a bad adhesive can include exposure to extremely high temperatures over extended periods, contamination by dirt or grease, or the natural aging and drying out of the adhesive.

Symptoms of a bad high temperature adhesive include:

• Components or parts becoming loose or detached
• The adhesive becoming brittle or cracked
• Inability to properly bond surfaces exposed to high heat
• Visible deterioration or peeling of the adhesive

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Replacement screw for dryers and laundry centers. Used throughout the cabinet to secure panels, drum supports, and components. Replace if missing or stripped.

This damper is the refrigerator air-control flap that regulates airflow between compartments to help maintain consistent temperatures and proper cooling. It replaces a worn or stuck damper to restore normal airflow and temperature balance. What it does:

• Opens and closes to direct cold air where needed between freezer and fresh-food sections
• Helps maintain even temperatures and prevents one compartment from getting too warm
• Common symptom: uneven cooling or warm fresh-food section despite running compressor
• Common symptom: damper stuck or not moving, causing poor temperature control

• Disconnect power to the appliance before starting any repair
• Remove interior panels to access the damper; use basic hand tools
• Handle the damper and any wiring harness carefully to avoid damage
• After installation, verify damper operation and allow time for temperatures to stabilize

Electrical wire harness for dryers. Replaces damaged, frayed, or worn internal wiring connections. Essential when harness is broken or corroded.

This door switch senses whether the appliance door is closed and signals the controls to run only when it's safe. Replacing a worn or intermittent switch restores dependable starts and proper shutoff when the door opens. What it does:

• Detects door position and allows operation only when the door is fully closed
• Interrupts operation when the door opens for safety
• Common symptoms include: won't start, stops when the door is moved, or "door open" message/error
• Intermittent starts due to worn actuator or internal switch contacts

• 1 door switch

• Disconnect power before servicing
• Access the switch from the front or top panel; release mounting screws or tabs
• Move wires to the new switch one at a time to maintain correct positions, then secure the switch
• Test operation before reassembly

Traps lint and debris during drying to prevent clogs and maintain efficiency. Replace if cracked, warped, or damaged. Verify fit by model number.

Secures hose connections in dryers to prevent leaks and maintain proper airflow. Replace if hoses are loose or disconnected. Verify fit with model.

Secures components inside your dryer to prevent shifting during operation. Replace this retainer if it's damaged, missing, or broken to eliminate noise.

Washer that fits between the support roller and shaft in your dryer. Replace if worn, cracked, or missing to maintain proper drum alignment and support.

Supports and guides the dryer drum as it rotates. Replace if the roller is cracked, worn, or causing noise. Sold individually, not pre-assembled.

Replacement nut that secures internal components in dryers. Restores clamping force when original nut is stripped, worn, or missing. Prevents loosening.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

Replacement mounting screw for dryers. Secures panels, brackets, and internal components. Replace if stripped, missing, or corroded during repairs.

This inner oven door glass panel replaces damaged or broken oven door glass to restore safe viewing and help the door seal properly. It's the interior glass used behind the outer door for protection and visibility. What it does:

• Replaces cracked, chipped, or shattered inner oven door glass
• Restores clear view into the oven cavity for safe cooking checks
• Helps maintain the oven door's sealing surface and inner insulation
• Prevents loose glass pieces from falling into the oven cavity

• Wear cut-resistant gloves and eye protection; broken glass is sharp
• Remove the oven door per the manufacturer's instructions before disassembly
• Handle with care to avoid scratches or chipping the edges
• Keep track of all fasteners and orientations for reassembly

Fastens panels, brackets, and internal components in your dryer. Replace stripped, rusted, or missing screws to restore secure mounting and alignment.

Replacement mounting screw for dryers. Secures panels, brackets, and internal components. Order if your original screw is stripped, missing, or damaged.