Parts for Ge GFD55ESMN3WW: Front Panel Parts

Drum roller assembly with axle and clips that supports the dryer drum and allows smooth rotation. Replace if worn, cracked, or causing loud noises.

This pulley nut secures the washer's drive pulley to the shaft to keep the belt aligned and power transfer reliable. Replacing a worn or missing nut restores stable spin performance and helps prevent belt slippage and noise.

• Locks the drive pulley to the shaft for proper belt alignment and consistent power transfer
• A loose or stripped nut can cause pulley wobble, belt squeal, slippage, or the belt coming off
• Replace if the original nut is damaged, missing, or will not stay tight after adjustment

• Disconnect power and water supply; safely tip or elevate the washer for bottom access
• Remove the drive belt; hold the pulley while loosening the nut (verify thread direction—do not force)
• Hand-start the new nut to avoid cross-threading; tighten securely per service information and confirm pulley runs true
• Reinstall the belt, verify alignment, and rotate by hand before restoring power

This stainless steel machine screw secures appliance components and trim for a reliable, corrosion-resistant hold. Use it when replacing lost or damaged fasteners to restore proper fit and reduce noise or misalignment. What it does:

• Fastens panels, brackets, and small assemblies where a #8-28 threaded screw is required
• Provides a rust-resistant connection for wet or humid appliance areas
• Helps stop rattling, loose trim, or misaligned parts caused by missing or stripped screws

• Disconnect power to the appliance before servicing
• Use the correct screwdriver or driver bit to avoid stripping the head
• Thread carefully by hand to avoid cross-threading; tighten until snug—do not overtighten
• Keep removed screws organized to ensure correct reassembly

Screens lint and debris from the dryer air stream. Replace when damaged, cracked, or no longer filtering properly. Verify fit using your model number.

This white front panel restores the clean appearance and protective face of the appliance control console. It replaces a cracked, chipped, discolored, or otherwise damaged front surface to improve looks and protect internal components. What it does:

• Covers and protects the control area and underlying components from dirt and damage
• Restores a finished, like-new appearance when the original panel is cracked, peeled, or stained
• Helps prevent debris from entering the console area and interfering with buttons or switches
• Works with existing trim, buttons, and mounting points to maintain proper fit

• Disconnect power to the appliance before starting any work
• Remove knobs, trim, and any retaining screws to access and replace the panel
• Handle edges carefully to avoid scratches; avoid contact with circuit boards and connectors

8-18 x 9/16-inch hex washer head screw secures panels, brackets, and trim in appliances. Replace missing, damaged, or stripped screws for proper fit.

This machine screw secures panels, brackets, and internal components in compatible washers. Replacing a missing or stripped fastener restores a tight fit to help reduce vibration and keep parts properly aligned.

• 10-32 thread; 5/8-inch length; To

Covers and protects the drum opening while maintaining proper airflow. Replace if cracked, broken, or allowing lint buildup. Verify fit with your model.

Fix dryer drum rubbing, scraping, or loud operation with this front drum support assembly. Centers and supports the drum for smooth, quiet rotation.

This sensor rod harness connects a temperature sensor to the appliance wiring, restoring proper signal transmission for accurate temperature monitoring and control. It's a direct-fit replacement when the original harness is damaged or intermittent. What

This door switch senses when the dryer door is closed so the cycle can start, and cuts power when the door opens. Replacing a faulty switch restores safe operation and consistent start/stop behavior tied to the door. What it does:

• Detects door o

The Door Strike is an OEM component for GE electric clothes dryers. It serves as the metal contact point that secures the dryer door tightly shut during active cycles via magnetic latching. 

Symptoms of a faulty door strike include:

Size: 8 - 18 ab.