Gaggenau Cooktop Parts

This door latch assembly secures the door closed and signals the control that it's safely shut, allowing cycles to start and run. Replacing a worn latch restores a reliable safety interlock and consistent operation.

• Secures the door and engages the safety interlock so the appliance can operate
• Sends a "door closed" signal to the control
• Common symptoms: door won't latch or stay closed; unit won't start or pauses as if the door is open; intermittent operation when the door is bumped; visible wear or damage to the latch
• Helps prevent nuisance "door open" indications

• Disconnect power before servicing
• Access the latch from the door area; remove inner panel or trim as required by your model
• Note wire positions, transfer connectors, and mount the new latch in the same orientation
• Test door closure before reassembly

Restore smooth, controlled door movement and a tight oven seal with this door hinge. Replacing a worn hinge helps the door close fully, prevents heat loss, and brings back the original opening tension on top or bottom compartments.

• Controls door swing and spring tension for smooth opening/closing
• Maintains alignment so the door gasket seals evenly
• Helps the door stay closed during cooking and hold at designed positions
• Common symptoms: door won't close fully, drops/sags, uneven gap, squeaks/binds, or heat escaping

• Disconnect power at the breaker and allow the oven to cool completely
• Remove the door; support it to safely relieve hinge spring tension
• Note hinge orientation and attachment points; transfer and secure the hinge using existing mounting locations
• After reassembly, verify latch engagement and even gasket contact; many ovens use two hinges—replace in pairs if both show wear

This is a sealing gasket designed to create an airtight fit on an oven or range component such as a door or lamp glass assembly. It prevents heat from escaping and protects internal parts from moisture and debris. Replace this seal if you notice heat leaking from the oven, uneven cooking temperatures, or visible wear and cracking on the existing gasket.

This burner lid is the top cap for a three-piece gas cooktop burner. It protects the burner head and helps shape the flame for more even heating and stable performance during cooking. What it does:

• Covers the burner head and directs flame for consistent heat distribution
• Helps maintain stable flame pattern and reliable ignition behavior
• Replaces lids that are cracked, chipped, warped, or corroded
• Can reduce uneven cooking or flickering/unstable flames caused by damaged lids

• Turn off gas supply and power to the appliance and allow all parts to cool fully before servicing
• Remove the old lid and seat the new lid squarely on the burner head; ensure it does not obstruct the igniter or burner ports
• Inspect surrounding burner components for damage; replace any damaged rings, caps, or gaskets as needed

Replacement burner head for gas cooktops. Restores even flame distribution when original is corroded, damaged, or worn. Direct-fit part for VG models.

M4 rubber gasket creates watertight seal and reduces vibration around fasteners. Replace when worn, cracked, or leaking. Verify fit with your model number.

This burner lid is the replacement top cover for a VG 230/330 gas burner assembly, restoring proper burner protection and heat distribution for reliable cooktop operation. Designed to fit the OEM burner geometry and surface finish. What it does:

• Covers and protects the burner cap and inner components from spills and debris.
• Helps channel flame and heat for more even cooking performance.
• Reduces the chance of food or liquids reaching ignition parts that can cause burner issues.
• Common symptom: cracked, warped, or missing lids that allow uneven flames or visible damage.

• Turn off gas and power to the appliance and allow all surfaces to cool completely before servicing.
• Remove burner grates and caps as needed; lift out the old lid and seat the new lid in the burner recess.
• Inspect surrounding components (cap, electrode/igniter) for damage while installing.

Spring for knob that restores proper tension and return action to a control knob, helping knobs operate smoothly and stay in position. Use this small replacement when a knob feels loose, won't center, or won't return. What it does:

• Provides tension and return action for a control knob so it centers and responds correctly.
• Replaces worn or broken knob springs that cause loose, wobbly, or non-returning knobs.
• Works as the mechanical spring behind the knob's rotation and detent action.
• Small, straightforward part used wherever a control knob needs restored tension.

• Disconnect power to the appliance (unplug or switch off circuit breaker) before servicing.
• Remove the knob and any bezels per the appliance's service instructions to access the spring.
• Handle small parts carefully; keep orientation noted for correct reassembly.

This replacement temperature control knob restores a worn or broken dial so you can set oven or range temperatures accurately and safely. It provides a simple push-on fit for straightforward control panel operation. What it does:

• Replaces a cracked, stripped, or missing temperature control knob to restore user control
• Allows precise selection of temperature settings via the control shaft
• Improves grip and visibility of setpoint compared to damaged knobs
• Prevents slipping on the control shaft for consistent temperature adjustments

• One (1) temperature control knob

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove the old knob by pulling straight off the control shaft; push the new knob onto the shaft until fully seated
• If the knob does not fit, verify you have the correct shaft style and part number before forcing installation

This fast radiant cooktop element replaces a damaged or non-working surface burner to restore even, reliable heating on compatible electric glass-ceramic ranges. It's a direct-fit heating element designed for 4-wire connections. What it does:

• Heats cookware quickly via the radiant heating surface for stovetop cooking
• Replaces cracked, non-heating, or intermittently heating burners
• Restores consistent temperature response and even heat distribution
• Works with 4-wire cooktop wiring; matches OEM element size and mounting

• One fast radiant cooktop element (180 mm / 7 in., 4-wire)

• Disconnect power at the breaker before servicing the cooktop to avoid shock
• Handle glass-ceramic surfaces carefully to prevent cracking; lift element per your model's service instructions
• Match wire colors/terminals exactly and secure connections;
• Test cooktop function after installation and re-seat any trim or retainers per the manufacturer guide

This is a control knob designed for use on a gas range cooktop or oven. It attaches to the control shaft and allows you to select burner or oven temperature settings. Replace this knob if it is cracked, broken, or if the printed markings have worn off, making it difficult to set the correct heat level.

The grill heating element is a 230-volt, 1500-watt radiant coil or surface element that generates intense direct heat for grilling or broiling food in your range or cooktop. It glows red-hot to sear and brown food from above or below depending on its position. Replace this element if it no longer heats up, heats unevenly, has visible breaks or burn spots, or causes your circuit to trip when in use.