Gaggenau Dishwasher Parts

Dishwasher not spraying water or dishes staying dirty? The circulation pump motor distributes water to spray arms. Moderate DIY repair, about 3 hours.

Repair set for dishwasher rack rollers. Restores smooth rack movement when wheels are broken, cracked, or worn. Installs on upper or lower racks.

This terminal block is the appliance wiring connector that secures incoming power and links internal circuits, restoring a safe, reliable electrical connection. Replaces a damaged or burned block to help prevent intermittent power or arcing. What it does

• Provides a secure connection point for incoming power leads and internal wiring
• Restores continuity when a cracked, corroded, or burned terminal causes loss of power
• Helps stop arcing, sparking, or overheating at the power entry point
• Used where multiple wires must be joined and fastened to the appliance chassis

• One terminal block

• Disconnect all power before inspecting or replacing the terminal block
• Verify wire locations and take photos or label wires before removal for correct reassembly
• Tighten connections to manufacturer torque spec—do not over-tighten screws
• If you see extensive burn or damaged wiring, replace damaged wires.

Fix a dishwasher that won't start or stops mid-cycle. This door switch detects when the door is closed and signals the control board to begin operation.

Replacement silverware basket holds and organizes forks, knives, and spoons in your dishwasher. Replaces cracked, broken, or missing cutlery holders.

Fix dishes not drying or cycles taking 3+ hours. This heating element heats wash water and enables drying. Moderate DIY repair with video guide.

Detergent door won't close or stay shut? Replace the dispenser assembly. Takes about 20 minutes with basic tools—remove inner door panel and swap out.

Rear pump housing for the washer drain/pump assembly. Replaces the worn rear housing that supports the impeller and bearing, helping restore proper draining and reduce leaks or unusual pump noises when the housing fails. What it does:

• Houses and supports the pump impeller and bearing, forming the rear half of the drain pump assembly.
• Restores a sealed mounting surface to help prevent water leaks from the pump area.
• Helps re-establish correct water flow and draining when a cracked or worn housing impairs the pump.
• Addresses symptoms such as poor or no draining, water at the base of the appliance, or loud/grinding pump noises.

• Disconnect power and shut off water supply before starting; drain any standing water to avoid spills.
• Remove the washer access panels and pump assembly; transfer the impeller, seals, and any hardware as required.
• Inspect and replace pump gaskets/seals and the impeller if worn; tighten mounting fasteners to OEM torque where specified.

Tall item spray head that attaches to the upper feed tube in your dishwasher. Replace if cracked, broken, missing, or won't lock into place properly.

Replacement front cover for dishwasher control module. Needed when plastic is cracked, broken, or switch actuators are worn or missing. Protects control board.

If your dishwasher detergent dispenser won't open during the wash cycle, this actuator lever assembly with springs restores mechanical movement.

Pump housing cover for dishwashers. Replaces cracked, broken, or missing covers that protect the pump assembly. Installs over the pump mechanism.

This rubber gasket seals appliance openings to help prevent water and air leaks and restore proper door/tub sealing. It replaces a worn or damaged seal to reduce leaking and maintain normal appliance performance. What it does

• Creates a watertight/airtight barrier between mating surfaces to prevent leaks.
• Helps maintain operating temperature and efficiency by sealing the door/tub.
• Common symptom: visible water around the door or base during use.
• Common symptom: cracked, flattened, or distorted seal material that no longer compresses.
• Works as a direct replacement for the matching OEM seal when damaged or worn.

• One gasket as shown on the product page.

• Turn off power and water supply to the appliance before starting any repair.
• Remove the old seal carefully, clean the mounting channel of debris and residue, and inspect the mating surface.
• Press the new gasket evenly into the channel, starting at one corner and working around to ensure full seating without twists.
• Test the door closure and run a short cycle to confirm there are no leaks; re-seat if necessary.