Garbage Disposal Gasket & Seal

The Sink Flange Mounting Kit is an OEM part for GE garbage disposers. As a complete kit, it contains the necessary sink flange rings, gaskets, seals, and mounting hardware to properly install or replace a disposer unit under the kitchen sink. Securely fastening the flange to the sink drain opening, affords a sturdy connection point for attaching the disposer mechanism.  

Symptoms of a bad or worn-out sink flange mounting kit include:  

• Looseness, wobbling, or movement of the disposer unit when in use
• Leaks detected around the flange seal or mounting area  
• Strong vibrations being transmitted to surrounding sink components
• Difficulty removing or installing the disposer due to improper fitting

This OEM GE replacement kit prevents any installation issues by providing all new mounting pieces engineered to specification. Compatible brand disposers also include InSinkErator, Badger, Waste King, and selected Kenmore models.
 

This fiber flange gasket seals the food waste disposer's sink flange to the sink opening, helping prevent seep leaks and keeping the mounting secure. Replace it if the original is brittle, missing, or you notice moisture around the drain.

• Creates a watertight seal between the sink flange and the sink/mounting assembly
• Helps stop drips and seepage at the top of the disposer
• Restores a secure, properly aligned connection during flange/disposer reinstallation
• Typical symptoms: moisture under the sink near the drain, recurring leaks after tightening, a cracked or deformed gasket

• Disconnect power to the disposer at the breaker before beginning work
• Support the disposer, loosen the mounting ring, and remove the sink flange components
• Clean and dry mating surfaces; position the new gasket per your installation manual and reassemble
• Fill the sink to check for leaks before restoring power

This mounting gasket creates a tight, cushioned seal where a component attaches to its housing or bracket. Replacing a worn seal helps stop leaks and rattles while restoring a secure, reliable connection at the mounting point.

• Forms a seal between two mounting surfaces to help prevent leaks or seepage
• Cushions and isolates vibration for quieter operation
• Helps maintain proper alignment of the mounted component
• Replace if the gasket is cracked, flattened, brittle, or no longer sealing

• Disconnect power and shut off water or gas, if applicable
• Note the gasket's orientation before removal
• Clean and dry both mating surfaces; remove all old gasket material and residue
• Seat the new gasket evenly; reassemble and tighten fasteners snugly without overcompressing; test for leaks/operation

This is a replacement Seal - stopp that restores a secure seal to the original component, helping prevent leaks and keep the appliance operating normally. Use it when the original seal is worn or damaged. What it does

• Forms a tight seal at the mating surface to help stop water or air leaks
• Restores proper fit where a worn seal causes seepage or dripping
• Helps reduce related symptoms like water pooling beneath the appliance or visible leakage
• Simple, single-piece part designed to match the OEM sealing point

• Disconnect power to the appliance before starting work; turn off water supply if applicable
• Inspect mating surfaces and clean away debris or old sealant before installing the new seal
• Fit the seal fully into its groove or mounting location; do not stretch or twist the part during installation

This sink flange seal is a rubber gasket that creates a watertight seal between the sink and drain flange to help prevent leaks and water damage. Use it when the flange seal is cracked, flattened, or leaking. What it does:

• Seals the gap between the sink and drain flange to stop water from leaking under the sink.
• Helps prevent sink-edge water pooling and slow drainage caused by a failed seal.
• Reduces chance of odors from trapped water beneath the flange by restoring a tight seal.
• Restores proper fit when replacing a corroded or worn sink flange assembly.

• One sink flange seal (rubber)

• Turn off water supply and disconnect drain components before replacing the seal.
• Remove the drain flange assembly, clean mating surfaces, then seat the new seal evenly.
• Avoid stretching or cutting the seal; replace it if damaged or misshapen.