Need Help?
Call or text
Show parts
This part is discontinued by the manufacturer and is no longer available for purchase.
Replacement control knob for gas range valve stem. Installs on burner or oven controls. Needed when original knob is broken, cracked, or missing.
Burner orifice spud regulates gas flow to the burner on your range or cooktop. Replace if missing, damaged, or when converting between LP and natural gas.
Replacement fastener nut for gas ranges and cooktops. Secures panels and internal components. Needed when original nut is missing, stripped, or worn.
Usually ships within 4 - 14 days
Phillips head mounting screw for range control knobs and switches. Replaces lost, stripped, or damaged screws. 8-32 thread size for secure installation.
Secures the electronic board or module inside your cooktop. Replace if the bracket is cracked, bent, or missing to prevent component movement and wiring issues.
Burner won't spark or ignite? This ignition switch controls the spark module for gas range surface burners. Mounts on the valve assembly behind knobs.
Manifold pipe for gas ranges that distributes gas from the main supply to individual burner valves. Replace if cracked, corroded, or leaking gas.
Protective cover that slips over the gas valve shaft to shield valve components from spills, food debris, and moisture. Replace if cracked or missing.
Holds the orifice that regulates gas flow to the rear burner on your gas range. Replace if cracked, corroded, or damaged from regular use or wear.
Meters gas flow to your range's surface burner for proper flame size. Replace if the original orifice is clogged, damaged, or missing to restore correct burner performance.
Holds the gas orifice in place at the front burner on gas ranges. Replace if cracked, broken, or kinked from repeated lifting of the cooktop.
Fix an oven that won't heat, takes too long to preheat, or makes a whoosh sound when lighting. This bake burner assembly includes the igniter. DIY repair.
Delivers gas from the manifold to your range's surface burner. Replace this tube if it's cracked, leaking, corroded, or damaged to restore safe gas flow.
Secures the igniter to the burner assembly in gas ranges and ovens. Replace if stripped, missing, or damaged during igniter replacement or repair.
Insulation pad for gas range burner box. Replaces worn, damaged, or missing heat insulation. Installs inside the burner box compartment for protection.
Protective shield that covers the oven igniter. Replace if cracked, broken, or missing to shield the igniter from spills, drips, and falling debris.
Replace a cracked, broken, or missing endcap on your range. This cosmetic trim piece installs on the side panel to complete the finished look.
Exterior endcap that covers and finishes exposed trim edges on your range. Replace if cracked, broken, or missing to restore appearance and protect components.
Panel mounting screw secures trim, bezels, and internal components on ranges and cooktops. Replace when stripped, corroded, or missing to restore fit.
Replaces a cracked, leaking, or faulty oven gas valve and pressure regulator assembly. Installs in the oven burner control system on gas ranges.
Oven won't heat or takes forever to reach temperature? This igniter creates the spark to ignite gas for baking. DIY-friendly repair, 20-30 minutes.
Carries gas from the pressure regulator to the burner valve manifold on your gas range. Replace if the tube is damaged, cracked, or leaking to restore safe fuel flow.
Broil shield for gas ranges. Mounts inside the oven cavity to protect components from direct heat. Replace if cracked, warped, or damaged.
This terminal cover protects the oven/range power connection by covering the appliance's rear terminal block, helping prevent accidental contact and keeping wiring secure. It's a direct-replacement exterior cover for the unit's power terminals. What it does:
Secures the thermostat assembly to your gas range or oven frame. Replace this mounting screw if it's stripped, missing, or damaged during repairs.
Secures the gas valve assembly to the frame of your range. Replace this bracket if it's bent, broken, or missing to properly mount the valve components.