Parts for Magic Chef OEMMAYCONV8: Gas Controls Parts

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

Screw for gas ranges and ovens. Used to secure panels, brackets, or internal components. Replace if lost, stripped, or corroded during repairs.

Oven won't reach temperature or overheats? This thermostat monitors heating circuits and controls temperature. Moderate difficulty repair, requires back access.

Seals the gap between burner and cooktop surface to prevent spills from entering the burner opening. Replace if damaged or worn. Confirm fit with model.

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

Sheet metal pan head screw secures panels, brackets, and components to appliance cabinets. Replace missing, stripped, or corroded screws to restore fit.

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

Burner won't light or spark? This top burner igniter creates the spark to ignite gas on your stovetop. Easy DIY repair in under 5 minutes with a screwdriver.

Size: 10-24 x 3/8 inch.

Oven won't heat or ignite? This igniter kit solves slow heating and ignition failure in gas ovens. Moderate DIY repair in 30-60 minutes.

Burner won't ignite or control knob is hard to turn? This top burner valve controls gas flow to surface burners. Moderate DIY repair with basic tools.

Hand-tighten wing nut secures panels, brackets, and components in ranges and ovens for tool-free adjustment. Replace when lost, stripped, or broken.

Replace a worn or clogged gas burner orifice with this orifice fitting assembly to restore clean, controlled flame. It meters gas to the burner for reliable ignition and accurate flame size.

• Meters gas flow from the valve/manifold to the burner
• Supports reliable ignition and a stable, properly sized flame
• Common symptoms of a clogged or damaged orifice: weak or uneven flame, yellow tips, delayed ignition, or burner not lighting
• Replace if the fitting/orifice is stripped, deformed, or otherwise damaged

• Shut off the gas supply and disconnect power before servicing; allow the appliance to cool
• Access the orifice per your model's service instructions; remove burner components as needed
• Use the correct wrench; avoid cross-threading and do not overtighten
• After reassembly, restore gas and check all joints for leaks with a bubble solution; perform fuel-type conversions only with the proper kit and instructions