Parts for Inglis ITW4871FW2: Gearcase, Motor And Pump Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Washer not draining or leaving standing water? A faulty water pump often causes drainage problems. DIY repair with basic tools in under an hour.

Factory fastener that secures panels and components in your laundry center. Replace if missing, stripped, or corroded to maintain proper alignment.

Internal drain hose routes water from the washer tub to the external drain. Replace if cracked, leaking, or damaged from constant use or obstructions.

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

Fix loud clicking or grinding noises during spin cycles with this washer transmission gear case. Moderately difficult repair takes 1-2 hours.

This replacement 7-2-1 screw secures components in compatible Whirlpool appliances, providing a dependable fastener for panels and assemblies. Use it to restore proper fitment and reduce rattling or loose parts. What it does

• Fastens trim, panels, brackets, or internal assemblies to keep parts secure
• Helps stop vibration-related noise from loose components
• Restores correct mounting where the original screw is missing or damaged
• Matches the form and fit of the OEM fastener for intended attachment points

• One replacement 7-2-1 screw

• Use the correct driver to avoid stripping the screw head
• Hand-start threads before tightening to prevent cross-threading
• Tighten until snug—do not over-tighten to avoid damaging plastic or sheet-metal parts
• Disconnect power to the appliance before accessing internal areas

Washer won't spin or agitate? A failed drive motor stops drum rotation entirely. This replacement motor restores wash and spin cycles. 2-hour DIY fix.

Mounting screw for laundry center and washer units. Secures internal components and panels. Replace if stripped, missing, or damaged during repairs.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

The washer drive belt transfers motor power to the washer’s drive system so the basket spins and agitates. Replacing a stretched or broken belt helps stop squealing and slipping so cycles finish at proper spin speed.

What it does

• Links the drive motor to the washer’s drive/pulley system
• Restores spin and agitation when the belt is worn, glazed, or broken
• Can reduce squeal or burning-rubber smells from belt slip
• Helps prevent intermittent or no-spin conditions

What’s included
One drive belt.

Install notes

• Unplug power; turn off water
• Tip the washer back; remove the bottom shield/cover if present
• Route the belt over the motor and drive pulleys; rotate by hand to seat fully
• Inspect pulleys/drive parts for wear; run a spin or calibration test after install

This OEM Whirlpool belt is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washer models.

Washer won't spin or shows F7 E1 error? The shift actuator controls cycle transitions. Moderate DIY repair with video guide available.

This genuine replacement screw secures components in compatible Whirlpool appliances, restoring proper fit and preventing rattles or loose panels. Use it when original fasteners are missing, stripped, or damaged. What it does:

• Fastens panels, brackets or small components to maintain structural stability
• Replaces missing or worn screws that cause vibration, rattling, or loose parts
• Restores secure connections after repairs or part replacements
• Helps prevent further damage by keeping parts properly aligned

• Turn off and unplug the appliance before servicing to avoid shock or injury
• Use the correct screwdriver or bit to avoid stripping the head
• Thread carefully and hand-start the screw to prevent cross-threading
• Keep small parts away from children and pets during installation

If your washer won't start or the motor hums but doesn't spin, the capacitor may have failed. This part regulates electrical current to the motor.

Protective cover that encloses the drive belt and motor pulley. Replace yours if cracked, warped, worn through, or missing to shield moving parts.

Washer making loud grinding noise during spin or agitation? Drive clutch kit repairs worn clutch assembly. Moderate DIY repair, typically 30-45 minutes.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.