Parts for Kenmore 110.31312020 (11031312020, 110 31312020): Gearcase, Motor And Pump Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Washer loud during spin? Grinding or jet engine noise usually means failed bearings in the gearcase. Includes bearings and seals. Moderate difficulty repair.

This replacement 7-2-1 screw secures components in compatible Whirlpool appliances, providing a dependable fastener for panels and assemblies. Use it to restore proper fitment and reduce rattling or loose parts. What it does

• Fastens trim, panels, brackets, or internal assemblies to keep parts secure
• Helps stop vibration-related noise from loose components
• Restores correct mounting where the original screw is missing or damaged
• Matches the form and fit of the OEM fastener for intended attachment points

• One replacement 7-2-1 screw

• Use the correct driver to avoid stripping the screw head
• Hand-start threads before tightening to prevent cross-threading
• Tighten until snug—do not over-tighten to avoid damaging plastic or sheet-metal parts
• Disconnect power to the appliance before accessing internal areas

This WASHER  is an OEM part specifically designed for Whirlpool top-load washing machines. Tailored to fit seamlessly, this component ensures the efficient operation of the washer. It plays a crucial role in maintaining the stability and balance of the machine during the washing cycles.

A damaged or worn-out top-load washer can negatively impact the appliance's performance. Causes of a defective washer might include prolonged use, physical damage, or exposure to excessive weight or force, resulting in instability or imbalance during operation.

Symptoms of a bad WASHER may include:

• Excessive vibration or shaking during the wash cycle
• Difficulty in maintaining balance while spinning
• Noisy or erratic behavior during the operation

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.

Fix a washer that won't spin or agitate properly. This drive motor powers the wash basket rotation. Moderate DIY repair, typically 15-30 minutes.

Mounting screw for laundry center and washer units. Secures internal components and panels. Replace if stripped, missing, or damaged during repairs.

Washer making loud grinding noise during spin or agitation? Drive clutch kit repairs worn clutch assembly. Moderate DIY repair, typically 30-45 minutes.

Transmits power from motor to tub for spinning and agitation. Replace if squealing, squeaking, or washer won't spin. Confirm fit with your model number.

Plastic shroud that protects the drive pulley and belt mechanism. Replace if cracked or broken from wear. Confirm fit with your model number.

Secures panels and components in place. Replace this fastener if stripped, corroded, or missing to restore proper alignment and eliminate rattling.

The Capacitor is an OEM part for Whirlpool washing machines. This part helps regulate power supply and voltage levels. It smooths out voltage fluctuations to ensure consistent operation of the motor and internal components.

Causes of a bad capacitor can include faulty wiring connections, or simply wear and tear over time. Capacitors have a limited lifespan based on usage and wear.

Symptoms of a bad capacitor include:

• The washer failing to start or not completing cycles
• Unusual noises coming from the motor area
• Fluctuating water levels and inconsistent filling
• Lights dimming when the washer is running

This genuine Whirlpool OEM replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Screw: 8-16 x 3/8 inch.

Washer won't spin or shows F7 E1 error? The shift actuator controls cycle transitions. Moderate DIY repair with video guide available.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This genuine replacement screw secures components in compatible Whirlpool appliances, restoring proper fit and preventing rattles or loose panels. Use it when original fasteners are missing, stripped, or damaged. What it does:

• Fastens panels, brackets or small components to maintain structural stability
• Replaces missing or worn screws that cause vibration, rattling, or loose parts
• Restores secure connections after repairs or part replacements
• Helps prevent further damage by keeping parts properly aligned

• Turn off and unplug the appliance before servicing to avoid shock or injury
• Use the correct screwdriver or bit to avoid stripping the head
• Thread carefully and hand-start the screw to prevent cross-threading
• Keep small parts away from children and pets during installation

Shield component for laundry center washers. Replaces cracked, broken, or missing shields. Installs to protect internal components from debris and damage.

Fix washer not draining or F9E1 error code. This drain pump circulates and removes water during wash cycles. Moderate DIY repair, access from bottom.

Factory fastener that secures panels and components in your laundry center. Replace if missing, stripped, or corroded to maintain proper alignment.

Connects washer tub to drain pump. Replace if cracked, split, or chewed by rodents. Common wear from chemicals and rubbing against machine components.

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

Flexible drain hose that channels water from your washer tub to the drain outlet. Replace if cracked, leaking, abraded, or damaged during installation.

The Switch Mounting Screw is an OEM part compatible with Whirlpool washing machines. This screw securely mounts the cycle selector switch within the control console assembly. Proper fastening ensures dependable operation of control functions.  

Causes of a bad mounting screw can stem from stress cracks developing over multiple years of operation. Vibrations accumulate, slowly loosening connections housed in a wet environment.

Symptoms of a bad mounting screw include:

• Loose or rattling switch within the console face  
• Difficulty selecting cycles as buttons wobble out of place
• Water intrusion hastening corrosion of electrical terminals
• Potential shock hazards if live connections are exposed

This Whirlpool replacement screw restores a tight mounting point. It is compatible with brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.