Gibson Range / Cooktop / Oven Parts

Secures the glass light cover to your range oven cavity. Replace if the retainer is cracked, broken, or missing to keep the lens firmly in place.

Replacement screw secures panels, trim, and internal components in your appliance. Needed when original fastener is missing, stripped, or damaged.

This wiring harness connects and routes power between key refrigerator components, restoring proper electrical signals so fans, lights, compressor and ice/water functions can operate correctly when the original harness is damaged. What it does:

• Provides the factory routing and connectors to link controls, motors and sensors
• Replaces frayed, burnt or broken wires that can cause intermittent power or no-power to components
• Helps resolve symptoms such as lights or dispenser not working, fans not running, or ice maker/pump failures when wiring is the cause
• Maintains factory-style connector fit and wire lengths for correct component connections

• Disconnect power to the appliance before inspecting or replacing the harness
• Match the part number and connector shapes to the original; route and secure wires per factory clips to avoid heat or pinching
• If connectors are corroded or terminals are damaged, replace the harness rather than attempting temporary repairs

Size: 8 inch. 2200 watt. Radiant.

This gas supply tube routes fuel from the valve/manifold to a burner in your gas cooking appliance. A sound tube helps deliver a steady flame and safer, reliable operation by maintaining a sealed path to the burner.

• Directs gas from the control valve/regulator to the designated burner
• Maintains a sealed pathway to help prevent leaks
• Supports proper ignition and consistent flame size on the affected burner
• Common signs of a problem: gas odor near the tube, visible kinks/corrosion, hissing, or weak/no flame

• Disconnect power and shut off the gas supply; allow the appliance to cool
• Work in a well-ventilated area; support fittings with two wrenches to avoid stressing the valve/manifold
• Route the new tube exactly like the original; start threads by hand and tighten securely without over-torquing
• After reassembly, restore gas and check all joints with an approved leak-detection solution.

Replace a cracked, broken, or missing oven door spacer that maintains proper alignment and gap between door components. Installs in door assembly.

Secures the gas burner assembly to the cooktop base. Replace stripped, rusted, or missing screws to eliminate burner wobble and maintain proper alignment.

This replacement surface burner cap sits on top of the gas burner head to focus and distribute the flame for even, efficient heating. Replacing a damaged or missing cap can restore proper ignition and flame pattern. What it does:

• Covers and protects the burner head from spills and debris
• Spreads and concentrates the flame for consistent cooking performance
• Helps prevent yellow, lifting, or uneven flames when properly seated
• Common symptoms: uneven or yellow flames, poor simmer, delayed ignition, chipped/warped/missing cap

• 1 surface burner cap

• Allow the cooktop to cool; disconnect power and shut off gas if servicing beyond simple cap replacement
• Lift off the old cap and clean the burner head surface of residue or debris
• Center the new cap on the matching burner head so it sits level—do not force
• Use the correct cap for the burner position; test ignition and flame after installation

Fiberglass insulation panel that installs behind the oven cavity. Replaces missing, damaged, or rodent-chewed insulation to restore heat containment.

Replacement oven door seal creates a heat-tight barrier to maintain temperature and reduce heat loss. Replace if heat escapes or cooking times increase.

Insulation wrap that surrounds the oven cavity to retain heat and protect outer panels. Replace if damaged, torn, or missing to restore heat retention.

Main top support rod for electric ranges. Replacement needed when original rod is broken, bent, or damaged. Installs to provide structural support.

Replace a cracked, broken, or missing outer housing cover on your range. This trim piece protects internal components and restores the finished look.

This clip secures the appliance's terminal block to the chassis, keeping wiring stable and preventing strain on electrical connections. It's a small, durable mounting clip used where the terminal block needs a fast, reliable hold. What it does:

• Holds the terminal block firmly to the appliance frame to reduce wire movement and wear
• Helps maintain safe, stable electrical connections by preventing strain on terminal wires
• Prevents the terminal block from shifting during use or service
• Compatible with standard terminal block locations that use a push-in or snap-mount clip

• One terminal block mounting clip

• Always disconnect power before accessing or servicing electrical components
• Remove access panels and locate the terminal block; clip typically snaps into a chassis slot or aligns with an existing mounting boss
• Handle wiring and terminals gently to avoid loosening connections; verify all wires are secure after reinstall

Drawer slide glide for electric and gas ranges. Replace if cracked, broken, or worn to restore smooth, aligned drawer movement and eliminate sticking.

Secures components inside your range or oven. Replace this bracket if it's bent, broken, or missing to restore proper mounting, alignment, and stability.