Parts for Viking Range VGIS48: Griddle Assembly Parts

Rear mounting bracket secures the griddle accessory to your gas range or cooktop. Replace if bracket is bent, broken, or missing hardware holes are damaged.

Front mounting bracket secures the griddle accessory to your gas range or cooktop. Replace if bent, broken, or missing to properly install your griddle.

Gas cooktop grill burner fixes uneven heating and weak flames. Common repair for Viking ranges. Moderate DIY install, typically 30-45 minutes.

Protects the thermal bulb sensor in your gas range or cooktop. Replace if damaged, bent, or missing to ensure proper oven temperature regulation.

This griddle box is the metal housing that holds the griddle burner and drip collection area, helping direct heat and contain grease for safe, consistent cooking performance. It restores proper griddle operation and containment of drips and smoke. What it does:

• Houses the griddle burner and aligns the flame and heat under the griddle surface
• Directs grease and drippings to the drip area to reduce flare-ups and smoke
• Helps maintain even cooking by stabilizing burner placement and airflow
• Replaces damaged or warped housings that can cause uneven heating or excessive smoke

• Shut off gas and electrical power and allow appliance to cool before servicing
• Inspect surrounding gasketing and mounting hardware; replace any damaged parts
• Tighten fasteners to secure the box and verify proper burner alignment before use

This is the oven control thermostat that regulates the temperature inside the oven cavity by cycling the heat source on and off to maintain the set temperature. It connects to the temperature-sensing element and the oven's control knob or panel. Replace this thermostat if your oven overheats, does not reach the correct temperature, cycles erratically, or fails to heat at all.

White griddle control knob for gas ranges and cooktops. Replaces cracked, broken, or missing knobs that control the griddle burner temperature setting.

Black griddle control knob for gas ranges and cooktops. Replaces worn, cracked, broken, or missing knobs on the griddle control valve for a finished look.

Black griddle control knob for gas ranges and cooktops. Replaces worn, cracked, broken, or missing knobs on the griddle control valve for a finished look.

Oven won't heat but igniter glows? This flat hot surface ignitor restores reliable gas ignition. DIY repair takes 45 minutes with basic tools.

Gas burner won't light or adjust properly? This valve and bolt kit restores precise flame control. Moderate DIY repair for most home mechanics.

Secures the thermal bulb sensing element in your gas range or cooktop. Replace if loose, damaged, or causing temperature control issues. Verify fit.

Uneven flames or incorrect burner output? This gas cooktop orifice hood regulates gas flow for proper flame height. Moderately easy repair.

Uneven flame or poor burner performance? This orifice hood centers and protects the gas orifice for steady flame control. Simple DIY repair part.

Replace your oven indicator light when it fails, flickers, or stays on. Restores clear operation status on your control panel. Verify fit with your model.

Replace your oven indicator light when it fails, flickers, or stays on. Restores clear operation status on your control panel. Verify fit with your model.

This 1/2" x 1/4" rubber bumper cushions contact points to reduce noise and prevent damage on appliance doors, drawers, and panels. It restores proper cushioning for smoother, quieter operation and helps maintain a snug fit. What it does:

• Absorbs shock where panels or doors meet to reduce rattling and clapping noises
• Prevents metal-to-metal contact that can cause chipping, scratching, or wear
• Helps doors and drawers close more evenly by restoring original spacing
• Commonly used where small, press-fit bumpers have worn, flattened, or fallen off

• One 1/2" x 1/4" rubber bumper

• Press-fit replacement; remove old bumper and press new bumper into the same hole until flush
• No special tools required; use a flat pick or small screwdriver to remove old bumper if needed
• Avoid installing on hot surfaces or near heating elements; let appliance cool before service
• Replace matching bumpers in the same area if others show wear for even performance

41-inch stainless steel flexible gas line for gas ranges. Replace if damaged, kinked, or during installation. Verify length and fitting size match your model.

70-inch stainless steel flexible gas supply tubing for gas ranges. Connects your range to the gas line. Replace if kinked, cracked, or damaged.

This is the wire assembly that connects the spark module to the rear burner ignitor on a gas range. It carries the electrical pulse needed to create a spark that ignites the gas at the burner. Replace this wire if the rear burner clicks but does not light, produces no spark at all, or if the wire insulation is damaged or burned.

This wire connects the spark module to the grill or griddle burner ignitor on a gas range. It carries the electrical spark signal needed to ignite the burner. Replace this wire if your grill or griddle burner clicks but won't ignite, or if you notice intermittent ignition failure due to a damaged or corroded wire.