Parts for Craftsman 247376381: Handle / Guard / 21" Deck Parts

Foam handle grip for lawn mowers and tillers. Replaces worn, torn, or missing grips on control handles. Provides cushioned comfort and secure hold.

Rope guide eyebolt for lawn mower recoil starters. Guides the starter rope smoothly during pull starts. Replace if bent, broken, or missing.

This replacement part is a washer. It is a genuine replacement part made by MTD. Washers are small but important components, allowing spacing in between certain parts near and around the engine. Washers are typically used alongside screws and nuts to provide a tight and secure fit of many different parts in the appliance.A new washer might be needed if the current one is damaged or missing. Washers need to be replaced as they become stripped. This is usually due to friction inside the machine. Be sure the engine is turned off before replacing this part. Typically washers are easy to replace and might only need a screwdriver during the repair. This washer is a genuine OEM replacement part. Note that it is sold individually. Be sure to purchase the correct amount as some machines require more than one.

Protective hub cap for walk-behind lawn mower wheels. Shields the wheel hub from dirt, debris, and moisture. Replace if cracked, broken, or missing.

Fix a mower that won't start or has loose throttle cable control with a new throttle housing. This plastic grip component secures the throttle cable.

Replacement discharge chute deflector for lawn mowers. Installs at the side discharge opening to direct clippings. Replace if cracked or missing.

Hinge pin fastener for lawn mowers. Secures moving components and panels. Replace if bent, missing, or damaged to restore proper attachment and function.

Replace worn spring bell washers causing loose parts or rattling noises. This conical washer cushions heavy loads in lawn equipment. Simple DIY fix.

This carriage bolt is a self-locking bolt designed to be used in an unthreaded square or round hole. These bolts are used in outdoor lawn and garden equipment due to their ability to handle heavy weight loads.Carriage bolts are often used to join lawnmower handles to the base of the mower. Over time, the vibration of the lawnmower may cause the bolt to become loose. During routine maintenance, if the bolt is loose, use a wrench to tighten the nut holding the bolt in place. If the bolt is missing, this carriage bolt replacement can be installed. Push the bolt through the hole; if the fit is snug, it may need to be lightly tapped. Once the bolt is through the other side, thread a nut on the bolt. Tighten the nut with a wrench.This is a genuine OEM part sourced directly from the manufacturer. It is sold as an individual unit and does not come with the nut. This carriage bolt is designed for lawnmowers, snowblowers, and other outdoor lawn and garden equipment manufactured by Bolens, Craftsman, Cub Cadet, Huskey, Troy-Bilt, Turf Pro, MTD, Ryobi, and Mastercut.

Nylon nut for lawn equipment. Secures and connects components throughout the machine. Replace if cracked, stripped, or missing for proper assembly.

Hex screw fastener for securing lawn mower components. Replace if stripped, rusted, or missing to ensure proper assembly and equipment stability.

Screw for lawn mowers, snowblowers, tillers, and outdoor power equipment. Replaces broken, stripped, or missing screws in internal or external machinery.

Star knob connects upper and lower handles on lawn mowers and outdoor equipment. Replace if threading is worn, cracked, or knob is missing for secure assembly.

Secures handle controls to the upper handle of your walk-behind mower. Replace this plastic housing kit if cracked, broken, or worn from outdoor use.

This is a seven-inch cable tie that is used with different types of lawn and garden equipment. It is most commonly used to secure the cable onto the handle of the lawnmower or tiller so it is secure. The cable tie is made of durable plastic but can be damaged or break. When this happens, the tie will need to be replaced to ensure the cable stays on the handle.If the cable tie needs to be replaced, no tools are needed. In the situation where other parts need to be replaced at the same time, a basic set of tools and a pair of work gloves may be required. Turn off the yard equipment and place it on a stable surface before replacing the broken cable tie. The old tie can be removed so the new one can be installed before further use.This cable tie is an authentic OEM replacement part that is directly sourced from the manufacturer. This product is sold individually. The component is designed to be compatible with lawnmowers, lawn tractors, tillers, and snowblowers manufactured by MTD, Troy-Bilt, Yard-Man, and Yard Machines.

Replaces worn, dull, or damaged 21-inch mulching blades on walk-behind mowers. Features curved design for effective mulching. Upgrade your rusty blade.

This is a bell-shaped washer used on lawn tractors to distribute load and provide a secure fit for bolts or fasteners. Its curved design helps maintain tension and prevents loosening due to vibration during mowing. Replace this washer if it is deformed, cracked, or missing, which can lead to loose hardware and component instability.

Hex screw fastener for lawn mower and lawn tractor small engines. Secures components together. Replace if lost, stripped, or corroded during maintenance.

Fastener spacer for lawn mowers and snow blowers. Creates proper gap between components to reduce friction. Replace if lost, cracked, or worn.

This carriage bolt is a self-locking fastener made for use in round or square holes to attach metal to metal in outdoor equipment. These bolts provide an added safety feature because they can only be removed from one side. Carriage bolts can carry a large amount of weight, which makes them ideal for use in outdoor yard equipment. Carriage bolts may be used to attach a lawn mower's arm to the side support and other similar applications. If the bolt needs to be replaced, removal and installation are simple. Use a wrench to loosen the nut holding the washer and bolt in place. Once the nut is loose, the bolt can be unthreaded by hand and pulled out of the hole. To install, push the bolt back through the hole. If the fit is too tight to install by hand, use a hammer to tap it in place. Reinstall the washer and nut and tighten with a wrench.This carriage bolt is designed for use in lawnmowers, snowblowers, and lawn tractors manufactured by Craftsman, Bolens, Yard Machines, Yard-Man, and MTD. This is a genuine OEM product that comes directly from the manufacturer. Note: It does not come with a nut or washer.

Hex washer head screw for lawn mowers and outdoor power equipment. Secures panels, covers, and components. Replace if stripped, missing, or damaged.

This hex screw and lock washer are commonly used with lawn mowers and other small engines to secure a motor to the housing of the equipment. It is machined in such a way that it binds the manifold and frame permanently. There are occasions when these bolts have to be removed, typically when major repairs are performed on the engine. In those cases, users often find it advisable to replace the hex bolts and washers with new ones. It happens as well that these screws are so tightly fastened that they cannot be unscrewed and must be cut off. In those cases, it is necessary to replace the original screws. These replacement screws and lock washers are genuine OEM certified replacements that are manufactured to be identical to the hardware they are replacing. In addition to mowers, these hex screws are used to secure engines to devices such as log splitters, edgers, shredders, trimmers, and snowblowers. This screw is compatible with devices made by Husky, Yard-Man, Cub Cadet, Troy-Bilt, Ryobi, Bolens, and Yard Machines.

This is a pawl that can serve as a replacement for some mower models, as well as chippers and shredders. The pawl attaches to the ratchet pawl plate. The pawl is essential for starting the engine. When the starter turns, the pawl is forced outward and locks onto the flywheel, allowing the engine to start. When the starter rope is let go, the springs pull back the ratchet pawls. If there is damage to the pawl, the engine will not start.The piece is made from durable metal, and it is built to last. However, it can start to wear down over time. Additionally, there is the potential that it could corrode. If there are issues with the pawl, replace them as soon as possible to ensure their machine continues to operate properly.This pawl can work with select models from MTD, Troy-Bilt, Yard-Man, Cub Cadet, and Husky. The piece is a genuine OEM replacement part sourced from the manufacturer. It is sold individually.

Replacement fastener for lawn mowers and tractors. Secures components and panels in place. Order a new fastener if yours is stripped, missing, or damaged.

Mower won't engage or self-propel? This clutch cable connects your control handle to the drive system. Moderate DIY repair, typically 30-45 minutes.

Drive belt transfers power from engine to wheels on self-propelled mowers and snow blowers. Replace if slipping, worn, or cracked. Verify fit by model number.

Metal blade support spacer that mounts between the mower blade and bolt. Secures the blade to the deck base. Replace if worn, damaged, or missing.

Secures handle controls to the upper handle of your walk-behind mower. Replace this plastic housing kit if cracked, broken, or worn from outdoor use.

Secures handle controls to the upper handle of your walk-behind mower. Replace this plastic housing kit if cracked, broken, or worn from outdoor use.

Control lever won't stay engaged or releases unexpectedly? This lawn mower latch secures the control lever in position. Quick DIY fix in 15 minutes.

This replacement curved hd. screw is also known as a carriage bolt. The screw can be used on many types of lawn and garden equipment. The purpose of the screw is to hold and support the upper and lower handles of the machine. It works along with the hand knob to help secure the handles, but buyers should know that the knob is sold separately. Owners might need to replace the carriage bolt if it has become corroded or no longer properly secures the handles. If the owner has lost the bolt, they will need to buy a new one before they can use their machine. The replacement for this part is fast and simple. This is an authentic OEM replacement curved hd. screw that is sold individually. It is for use with lawn mowers, tillers, snowblowers, wood chippers, edgers, and leaf blowers. It is compatible with certain models from Craftsman, Cub Cadet, Ryobi, Troy-Bilt, Husky, Yard Machines, MTD, Huskee, Montgomery Wards, Bolens, Yard-Man, and MasterCut.

Secures bolts and prevents loosening on mowers and tractors. This hex jam nut locks standard nuts in place for reliable fastening. Easy installation.

Control cable for walk-behind mowers. Connects handle controls to engine or drive system. Replace if frayed, kinked, stretched, or broken for safe operation.

Ratchet wheel for lawn mowers. Installs in the drive mechanism to enable continuous motion in one direction. Replace if cracked, worn, or damaged.

Hex screw fastener for securing lawn mower components. Replace if stripped, rusted, or missing to ensure proper assembly and equipment stability.

Flange bearing enables smooth operation and prevents overheating in lawn mowers. Replace if equipment runs rough or bearings show wear. Verify fit.

Hex cap screw fastener for outdoor power equipment. Secures components with hexagon-shaped head. Replace if stripped, broken, or missing threads.

Mower won't shift speeds or self-propel won't engage? This tooth rack gear insert transfers rotational motion to linear movement. DIY repair in 30 minutes.