Parts for Ge UVH13013M1TS: Hood Assembly Parts

This hood damper assembly replaces the vent flap that opens and closes to let exhaust air exit your range hood or over-the-range vent. It restores proper airflow control and helps prevent backdrafts when the hood is off. What it does:

• Opens to allow exhaust airflow during venting and closes to block outside air when not in use
• Prevents backdrafts and reduces drafts from entering the kitchen through the hood vent
• Stops rattling or sticking caused by a worn or damaged damper flap or hinge
• Helps restore normal ventilation performance when the original damper is broken or jammed

• One hood damper assembly (damper flap with attached hinge)

• Disconnect power to the range hood or appliance before starting any work
• Handle sheet-metal edges carefully; wear gloves to avoid cuts
• Basic hand tools are typically required; align hinge and test damper operation before finishing

A small retaining spring washer that provides tension and helps secure fasteners on appliance assemblies. Replaces worn or damaged washers to restore proper clamp and prevent loosening of mounted components. What it does:

• Applies spring tension to a fastener or shaft to maintain clamp and alignment
• Helps prevent bolts or shafts from backing out under vibration
• Commonly replaced when missing, flattened, or corroded
• Symptoms of a failing washer include loose parts, increased vibration, or rattling

• One spring washer

• Disconnect power before servicing electrical appliances
• Use the correct tools and exact OEM part number for fitment
• Inspect mating parts (bolt, shaft, housing) for wear and replace if needed

This charcoal filter traps odors in the recirculating vent system, helping your appliance freshen the air when it isn't ducted outdoors. Replace a saturated filter to restore effective odor reduction and keep ventilation working as designed.

• Adsorbs cooking odors from vapors as air passes through the filter
• Intended for non-vented operation of the ventilation system
• Common replacement signs: lingering smells, dark/saturated media, or crumbling when handled
• Works with clean grease filters to help maintain effective odor control

• Disconnect power to the appliance before servicing
• Remove grille or filter cover per your owner's manual; note filter orientation/airflow arrows if present
• Install without bending; ensure it seats fully and the grille/cover is secured
• Charcoal filters are not washable—replace when saturated or as recommended by the manufacturer

This metal mesh grease filter captures airborne grease from range hood or microwave exhaust to help keep the vent and fan cleaner and reduce buildup on internal components. It's a direct-fit replacement designed for easy swap-out. What it does:

• Traps grease and cooking residue to protect blower and ductwork
• Helps reduce unpleasant cooking odors from lingering in the exhaust
• Restores proper airflow by replacing damaged or clogged filter media
• Visible, removable filter makes maintenance straightforward

• Turn off power to the appliance before removing or installing the filter
• Slide or latch filter into place following the factory mounting points; do not force
• Handle edges carefully; filter frame may have sharp corners
• Clean or replace per manufacturer recommendations; only install correct part number for fit

This interface board routes control and display signals between the microwave/TV assembly and the hood, restoring communication for vent, light, and display functions. It's a direct-replacement control interface designed for factory fit and operation. What it does

• Transfers interface and control signals between the oven/microwave TV module and the hood/vent assembly.
• Restores responsive vent fan and hood lighting when a failed interface board causes loss of control or display communication.
• Helps resolve intermittent or no-response issues tied to the interface connection (shorts or failed circuitry).
• Works as the communication/connector board used in the appliance's control system.

• One interface board

• Disconnect power (unplug or shut off breaker) before beginning any service to avoid shock.
• Inspect connectors and wiring harness for damage; replace any frayed or corroded leads before installing the board.
• Handle the board by edges and avoid touching components; use proper ESD precautions if available.

This speaker wiring harness connects the control board to the oven/microwave chime or speaker so your appliance can signal status tones. It replaces a damaged or disconnected cable to restore audible alerts and proper control-panel feedback. What it does

• Carries audio/chime signal from the control board to the appliance speaker
• Restores missing or intermittent beeps, chimes, or other control-panel sounds
• Replaces frayed, burnt, or broken wiring and damaged connector ends
• Ensures a secure, correct electrical connection between components

• Disconnect power (unplug appliance or shut off circuit breaker) before installation
• Match connectors and routing to the original harness; do not force connectors
• Inspect mating connectors and boards for damage before connecting