Parts for Lg LFCC22426S/01: Ice Maker / Ice Bin Parts

Replacement mounting stud for refrigerator door handles. Installs inside the door to secure handle assembly. Needed when stud is damaged or missing.

Plastic drain tube that channels defrost water from evaporator coils to drain pan. Replace if cracked, melted, broken, or causing water leaks in freezer.

Leveling leg for refrigerators. Installs at bottom corner to elevate and stabilize the appliance. Replace if broken, compressed, or no longer secure.

Ice not dispensing or spilling? This refrigerator ice storage bucket collects and holds ice from your ice maker. Simple DIY install in 10 minutes.

Small protective cap covers component connections or openings in your refrigerator. Replace when cracked, missing, or worn to protect against dirt and moisture.

Supports and guides sliding refrigerator drawers or shelves for smooth rolling. Replace if worn, cracked, or causing wobbling, sticking, or noise.

Dual roller wheel assembly that mounts to the rear wall of the freezer drawer. Replace when wheels are missing, broken, or cracked for smooth sliding.

Replacement drawer pan that supports items inside your refrigerator drawer. Install when original is cracked, warped, sagging, or broken to restore storage.

Replaces a cracked, warped, or broken drawer tray in your bottom-mount refrigerator. Restores stable storage support and smooth drawer operation.

Replaces a cracked, warped, or broken drawer tray in your bottom-mount refrigerator. Restores stable storage support and smooth drawer operation.

Replace a cracked, broken, or missing right-side refrigerator shelf. Restores safe, level storage for food containers and everyday items in your fridge.

Left-hand shelf assembly for bottom-mount refrigerators. Replaces cracked, broken, or missing shelves. Installs inside fresh food compartment.

Note: Shelf is on the LEFT side. 

Replace your refrigerator's mesh shelf net when torn or stretched to restore organization and prevent items from falling through. Verify fit with your model.

Replacement door shelf net that secures small items in your refrigerator door. Installs on door shelf to replace cracked, stretched, or missing nets.

This is a cover assembly that sits on top of the vegetable crisper drawer area in the refrigerator compartment. It acts as a shelf and humidity barrier, helping maintain proper moisture levels for fruits and vegetables stored in the crisper bins below. Replace this cover if it is cracked, warped, or no longer sits flush, which can lead to poor humidity control and wilting produce.

Replacement shelf holder for bottom-mount refrigerators. Secures and supports shelves in place. Needed when original is cracked, broken, or missing.

Supports the fresh room crisper drawer area and contains spills in your refrigerator. Replace this tray if cracked, warped, or broken to restore drawer fit.

Replaces a cracked, broken, or missing tray cover in your bottom-mount refrigerator. Restores a finished appearance and protects the tray area.

Molded plastic cover that protects the internal tray area in your refrigerator. Replaces cracked, warped, or missing covers to restore containment.

This is a decorative front panel that attaches to the deli or fresh food drawer inside the refrigerator. It serves as the visible face of the drawer and provides a handle area for opening and closing it. Replace this cover if it is cracked, warped, discolored, or if the mounting tabs have broken, causing the panel to detach from the drawer.

Replacement decor cover for bottom-mount refrigerators. Restores front trim appearance and conceals mounting hardware. Needed when original is cracked, dented, faded, or missing.

Replaces a cracked, broken, or missing crisper drawer tray in your bottom-mount refrigerator. Provides stable support under vegetable drawers.

Replacement vegetable crisper drawer tray for bottom-mount refrigerators. Restores proper storage when original tray is cracked, broken, or missing.

Refrigerator lamp cover protects the interior light bulb. Replace if cracked, discolored, or broken to restore proper lighting. Verify fit with model.

Dim or uneven refrigerator lighting? This lamp cover protects and diffuses your interior light. Direct-fit replacement lens, simple installation.

Replaces a cracked, broken, or missing tray cover in your bottom-mount refrigerator. Protects tray surface and prevents spills or contamination.

Replaces worn or damaged drawer slide rail in bottom-mount refrigerators. Restores smooth gliding and proper alignment when original is cracked or broken.

Supports and guides refrigerator drawers or racks for smooth sliding. Replace if your guide is cracked, broken, worn, or causing misalignment or detachment.

Restores insulated core inside freezer door to maintain cold retention and reduce frost. Replace when door loses cooling efficiency or frost builds up.

Restores insulated core inside freezer door to maintain cold retention and reduce frost. Replace when door loses cooling efficiency or frost builds up.

Left-side door handle trim for refrigerators. Restores finished appearance and edge protection. Replaces cracked, scratched, or missing trim pieces.

Exterior trim piece for refrigerator door handle. Replaces cracked, scratched, or worn decorative trim to restore original appearance and finish.

Replaces cracked, broken, or missing hinge trim on your refrigerator door. Snaps over the hinge mechanism to restore a clean, finished look.

Replaces worn or cracked hinge cover to restore a clean appearance and protect the hinge area from debris. Confirm fit with your refrigerator model number.

Replace your broken or cracked bottom-mount refrigerator freezer drawer handle assembly. Includes handle and mounting hardware for the lower freezer compartment.

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

Replace worn door foam insulation to restore thermal efficiency and proper sealing. Fixes cold spots and temperature fluctuations. Confirm fit with model number.

Complete refrigerator door assembly including inner liner and outer panel. Replaces cracked, damaged, or worn doors that compromise temperature seal.

Seals the refrigerator door to prevent cold air leaks, frost buildup, and temperature fluctuations. Replace if torn, cracked, or no longer sealing tightly.

The Refrigerator Flipper Assembly is an OEM part for LG refrigerators. This assists in the smooth opening and closing of the refrigerator door. It ensures an airtight seal when the door is closed, preventing cool air from escaping and maintaining the refrigerator's internal temperature. 

Causes of a malfunctioning Refrigerator Flipper Assembly can range from physical damage, such as cracks or breakage, to wear and tear from regular use.

Symptoms of a bad Refrigerator Flipper Assembly include:

• Difficulty in opening or closing the refrigerator door
• A noticeable gap when the door is supposed to be sealed shut
• Increased energy consumption as the refrigerator works harder to maintain its temperature
• Spoilage of food items quicker than expected due to poor temperature regulation

This OEM LG part is also compatible with some Kenmore models.

Drawer guide rail for bottom-mount refrigerators. Installs on the drawer frame to ensure smooth sliding. Replace if cracked, broken, or worn out.

Replace a cracked or broken door bin to restore secure storage. Mounts to the refrigerator door for organizing bottles, jars, and condiments.

Door stopper assembly for refrigerators. Installs on the door to limit opening angle and prevent wall damage. Replace if cracked, broken, or missing.

Fix clicking doors or misaligned refrigerator doors with a new hinge cam. Restores smooth open/close action and proper door alignment. DIY-friendly repair.

Hinge assembly for refrigerator doors. Installs at door pivot point to support door weight and enable smooth opening/closing. Replace if cracked or worn.

Plastic door stop that limits refrigerator door swing range. Replaces broken, cracked, or missing stoppers causing doors to swing too wide or close improperly.

Refrigerator door handle assembly that mounts to the exterior door surface. Replace when the original handle is cracked, broken, loose, or missing.

This connector rail secures and routes electrical connections in the appliance, keeping wiring organized and supporting reliable connections for proper operation. It helps prevent loose harnesses and reduces strain on wiring during use. What it does:

• Provides a stable mounting point for wire harness connectors and plugs
• Maintains correct alignment and spacing of electrical connections
• Reduces stress on wiring to help prevent intermittent connections
• Commonly used when loose or damaged connector mounts cause power or control issues

• Disconnect power and unplug the appliance before starting any work
• Handle connectors and wiring gently to avoid damaging pins or insulation
• Reinstall in the original orientation and secure mounting fasteners snugly

Mounting rail that holds and aligns connector assemblies inside your refrigerator. Replace if cracked, broken, or missing to restore secure fit.

Guides and supports refrigerator drawers as they slide in and out. Replace if your rail is cracked, broken, or worn to restore smooth drawer movement.

Drawer slide rail allows refrigerator shelves and drawers to glide smoothly. Replace if drawers stick, wobble, or won't close properly. Verify fit with model.

Fix refrigerator electrical issues with this wire harness assembly. Connects key components for proper operation. Moderate DIY repair for bottom-mount models.

Ice maker grinding or not ejecting cubes? This gear drives the ejector blades to push ice from the tray into the bin. Restores harvest cycles quickly.

Secures and pivots the center refrigerator door for proper alignment and sealing. Replace if your door sags, won't close fully, or pivots roughly. Verify fit by model number before ordering.

Secures and pivots the upper refrigerator door for proper alignment and smooth opening. Replace if your door sags, won't close properly, or hinge is damaged. Verify fit by model number before ordering.

Replacement ring for your refrigerator. Installs on internal components to secure or seal parts. Order a new ring if yours is cracked or missing.

The Spanner Wrench is an OEM replacement part for LG refrigerators. This tool allows you to adjust the door hinges to ensure the doors are level and aligned properly. A well-aligned door is crucial for maintaining the internal temperature and efficiency of the refrigerator, preventing energy loss and ensuring food is stored under optimal conditions.

Symptoms that you might need to adjust the door hinges and potentially need this wrench include:

• Doors not closing properly or sealing tightly
• Visible gaps between the door and the main body of the refrigerator
• The refrigerator tilting or not sitting level

This spanner wrench is also compatible with some Sears/Kenmore refrigerators. 

Secures and pivots your refrigerator door at the top for proper alignment and smooth operation. Replace if door sags or seals poorly. Verify fit.

Replacement refrigerator door hinge that restores smooth pivoting and proper door alignment, helping the door open and close reliably and maintain an airtight seal to preserve cooling performance. What it does:

• Supports the refrigerator door and allows it to pivot smoothly.
• Replaces worn, bent, or damaged hinges that cause door sag or misalignment.
• Helps reduce noisy or grinding door operation when the hinge is failing.
• Promotes an even door seal to help maintain internal temperature consistency.

• Unplug the appliance and remove food from nearby shelves before starting work.
• Support the door while removing hinge fasteners to prevent dropping or damage.
• Reinstall using the original hardware; align the door and tighten fasteners securely but avoid overtightening.

Fix a refrigerator not cooling or freezing over with a new evaporator coil assembly. This part circulates refrigerant to cool your fridge compartments.

Rattling or loose parts in your refrigerator? This retaining pin secures moving components and keeps them aligned for smooth, quiet operation.

Support roller that mounts to the refrigerator base, allowing the unit to roll for cleaning or service. Replace if worn, broken, or causing uneven positioning.

This motor support damper sits between the refrigerator's compressor and base to absorb vibration and movement. Replacing a worn damper helps quiet rattles and humming from the back of the cabinet and keeps the compressor properly supported.

• Cushions the compressor to reduce transmitted vibration and noise
• Helps quiet humming, buzzing, or rattling from the lower rear of the refrigerator
• Maintains proper compressor alignment and support on the base pan
• Common signs of wear: increased vibration/noise, a cracked or flattened damper, or noticeable compressor movement when running

• Unplug the refrigerator and pull it forward to access the rear; allow the compressor to cool before working
• Support the compressor to remove load from the mount before loosening hardware
• Replace the damper and tighten mounting hardware evenly without over-compressing the rubber
• Avoid bending or stressing refrigerant tubing; wear gloves and eye protection

Fix a refrigerator not cooling properly with this compressor sealing pipe. Essential sealed system component for restoring proper refrigeration.

Drain tray assembly that collects condensation beneath your refrigerator. Replace if cracked, broken, or missing to prevent water leakage issues.

Vibration-isolating grommet that mounts between the compressor and chassis. Replace if cracked, worn, or missing to restore proper cushioning.

Rear machinery compartment cover assembly for bottom-mount refrigerators. Replaces cracked, broken, or missing covers that protect compressor components.

This is a small retainer clip that secures the compressor in place at the base of the refrigerator. It helps prevent the compressor from shifting or vibrating excessively during operation. Replace this clip if your refrigerator produces unusual rattling or vibrating noises from the back, or if the compressor appears loose or has shifted from its mounting position.

This restrainer is a small retaining clip that helps secure moving or removable components in place, reducing rattles and keeping parts aligned for reliable operation. It's a simple replacement for worn or broken clips. What it does:

• Holds a cover, panel, or door-related component in proper position to prevent shifting
• Reduces noise caused by loose or vibrating parts
• Restores original fit where a broken or missing clip allows movement
• Simple mechanical function — no electrical connections or calibration

• One restrainer

• Disconnect power (and water if applicable) before beginning repairs
• Inspect surrounding mounting points for damage; replace any broken tabs or fasteners
• Typically installs with basic hand tools; align clip and press or snap into place until secure

This noise damper reduces vibration and rattling sounds from refrigerant lines in your refrigerator. It cushions the copper tubing against the cabinet to prevent metal-on-metal contact that creates annoying noises. Install this damper if your refrigerator makes clicking, rattling, or vibrating sounds, especially when the compressor cycles on and off.

This holder is a small mounting bracket used to secure internal components in place, helping keep parts aligned and stable for reliable operation. It provides a direct, OEM-compatible replacement to restore proper fit and function. What it does

• Secures and supports nearby components to prevent shifting or vibration.
• Restores proper alignment where a worn or broken holder causes rattling or loose parts.
• Helps maintain normal operation by keeping assemblies seated correctly.
• Works behind panels or inside assemblies where a dedicated bracket is required.

• One holder/mounting bracket as shown.

• Installation generally requires removing the panel or access cover where the holder is located.
• Use proper fasteners shown in your appliance; replace any damaged screws or clips as needed.
• Disconnect power before servicing electrical appliances to reduce shock risk.

This condenser assembly connects and secures the refrigerator condenser components, helping the cooling system run reliably. It replaces damaged or corroded condenser wiring to restore proper condenser function and airflow. What it does:

• Provides the OEM-configured wiring and mounting for the condenser to ensure consistent electrical connection.
• Restores proper condenser operation when original wires are cut, burnt, corroded, or loose.
• Helps prevent intermittent cooling or compressor issues caused by faulty condenser connections.
• Maintains correct routing and strain relief for condenser lines to reduce wear and chafing.

• One condenser assembly with attached wiring and mounting hardware as shown.

• Recommended for technicians or confident DIYers; disconnect power before starting and unplug the appliance.
• Inspect surrounding components for damage; replace any compromised parts.
• Use proper tools and tighten mounting hardware to OEM torque where specified; avoid pinching wires.

Fix uneven cooling or warm spots in your refrigerator with a new evaporator fan blade. This part circulates cold air throughout the unit for consistent temps.

Fix a warm fridge or squealing fan noise with a new condenser fan blade. Circulates air over condenser coils. DIY repair takes about 30 minutes.

If your refrigerator is making unusual noises or cooling poorly, a damaged fan grille may be disrupting airflow. This housing protects the fan and restores proper cooling performance.

Fix refrigerator lights staying on or not turning off when door closes. This magnetic door switch is a common solution. Simple DIY repair in 15 minutes.

This DC motor drives the evaporator fan that circulates cold air from the evaporator coils throughout the refrigerator and freezer compartments. It is essential for maintaining even, consistent temperatures inside the unit. Replace this motor if the refrigerator is not cooling properly, the freezer is cold but the fresh food section is warm, or you hear unusual buzzing or grinding noises coming from behind the interior back panel.

A replacement cover motor that powers the refrigerator's dispenser cover, allowing the door to open and close so you can access ice and water. Replaces a worn or failed motor to restore normal dispenser cover operation. What it does:

• Drives the dispenser cover mechanism so the cover opens when dispensing and closes when idle
• Helps keep the dispenser sealed to reduce drafts and prevent pests or debris from entering
• Stops or fails to move when worn, causing a stuck, slow, or noisy dispenser cover
• Works with the dispenser linkage and gears to coordinate cover motion with user controls

What's included:

• One cover motor

Install notes:

• Disconnect power to the appliance before beginning any repair
• Remove dispenser trim and access panel per your model's service instructions to reach the motor
• Handle gears and linkage carefully; ensure proper alignment during reassembly and test cover operation before finishing

Uneven cooling or noisy damper? This damper motor support bracket secures the air control assembly for proper airflow between compartments. DIY fix.

Refrigerator not cooling properly? This damper motor support secures the air damper assembly that controls airflow between compartments. Simple DIY fix.

If your refrigerator light stays on or interior won't cool properly, the door switch may have failed. This magnetic switch detects door position.

Interior light won't turn off when door closes? This refrigerator door switch cover protects and aligns the switch for proper operation. Simple DIY fix.

Fix ice buildup in your refrigerator with this defrost heater. Melts frost from the evaporator during defrost cycles to restore consistent cooling.

Fix a dim or flickering refrigerator interior with this LED light assembly. Direct replacement part restores bright, even lighting in minutes.

Illuminates your refrigerator display for clear, even brightness. Replace when you notice dark spots, dim areas, or missing segments on the screen. Verify fit with your model number before ordering.

Refrigerator not cooling or making clicking sounds? The compressor run capacitor provides electrical boost to start and run the compressor motor reliably.

Refrigerator not cooling evenly or running constantly? This DC motor assembly drives the fan to restore proper airflow and temperature control in your fridge.

Protective cover assembly that shields the printed circuit board (PCB) in your refrigerator. Replace if cracked, broken, or missing to protect electronics.

Ice maker overflowing or not stopping? This shut-off arm lever controls ice production by sensing bin levels. Simple plug-and-play repair.

Ice maker stopped producing ice or cycles too slowly? This complete ice maker assembly replaces a faulty unit. DIY-friendly installation in 10-15 minutes.

Fix inaccurate temperature readings or sensor errors with this refrigerator sensor control board. Restores proper sensor communication and feedback.

If your refrigerator display is dead, shows error codes, or behaves unpredictably, this sub PCB assembly processes inputs and controls specific functions.

The Temperature Sensor is an OEM part for LG refrigerators. Also known as a thermistor, is responsible for sensing the temperature changes and providing the necessary feedback to the refrigerator's control board. It helps maintain accurate and consistent temperature levels, ensuring optimal food preservation and efficient cooling.

Causes of a faulty temperature sensor can include wear and tear over time, damage due to electrical issues or exposure to extreme temperatures, or sensor calibration issues. These factors can result in temperature inconsistencies, inaccurate readings, or improper cooling performance of the refrigerator.

Symptoms of a bad temperature sensor may include:

• Incorrect temperature readings on the control panel
• Temperature fluctuations inside the refrigerator
• Overcooling or inadequate cooling of food items

This OEM LG part can also be used on Kenmore/Sears appliances. 

Secures and routes the water tube along the cabinet or door. Replace if cracked, broken, or missing to prevent kinks and keep tubing properly positioned.

Fix no water or ice issues with this refrigerator water inlet valve. Controls water flow to ice maker and dispenser. Moderate DIY repair, 30-45 minutes.

Secures bracket assemblies inside your refrigerator to keep components aligned and reduce vibration. Replace if cracked, bent, or missing.

This is a replacement filter cover that secures the air filter in place and protects internal components. It restores the proper fitment of the filter and helps maintain intended airflow and filtration performance. What it does:

• Holds the air filter securely so air passes through the filter media as designed
• Protects internal components from dust and debris
• Prevents gaps that can reduce filtration efficiency or allow unfiltered air bypass
• Helps reduce rattling or vibration caused by a loose or damaged cover

• One filter cover

• Disconnect power before accessing internal parts
• Remove the old cover by releasing retaining tabs or fasteners and align new cover until it snaps or locks into place
• Inspect nearby seals and the filter; replace if damaged
• Handle plastic parts gently to avoid cracking; do not force into place

Connects and seals your refrigerator's water filter cartridge. Replace if you notice leaks around the filter or reduced water flow. Verify fit with your model.

Removes impurities and contaminants for clean, fresh-tasting water and ice. Replace every 6 months or when water flow decreases. Verify fit with your model.

Secures and protects your refrigerator's air filter, maintaining proper airflow and filtration. Replace if cracked or loose. Verify fit with your model.