Parts for Lg LMXS28596M/01: Ice Maker & Ice Bin Parts

This replacement screw secures specified panels or components inside your appliance. Refreshing worn or missing hardware helps restore a tight fit, reduce rattling, and keep assemblies properly aligned for reliable performance.

• Provides secure fastening for brackets, panels, or internal assemblies
• Replaces stripped, rusted, or lost hardware
• Helps reduce vibration and rattling noises
• Symptoms include loose panels, shifting components, or a screw that won't tighten

• Disconnect power and allow any hot surfaces to cool before servicing
• Wear cut-resistant gloves and eye protection
• Match length and thread to the original; replace like-for-like
• Start threads by hand to avoid cross-threading; do not overtighten

The Handle Mounting Stud is an OEM replacement part for LG refrigerator doors. It provides a sturdy mounting point for the door handle assembly. Reliable handle connection and support is crucial for dependable door function and access. 

Causes of a faulty stud can include damage from excess weight or impact over time rendering the stud loose or unstable.

Symptoms of a bad stud include:

• Loose or sagging door handle  
• Difficulty opening and closing the refrigerator door  
• Potential for the handle to detach completely
• Safety concerns if the handle connection fails

This OEM LG replacement stud is also compatible with Sears/Kenmore models. 

The Drain Pipe Assembly is an OEM replacement part for LG refrigerators. It is a plastic tubing system that collects and removes liquid condensation from evaporator coils. Proper drainage is crucial to minimizing frost buildup and ensuring optimal cooling of food storage areas. 

Symptoms of a bad drain pipe assembly include:

• Excessive frost or ice accumulation inside the refrigerator
• Puddling or leaks detected near evaporator housing
• Slow draining allowing water to pool versus emptying fully
• Cracks or breaks in the tubing prevent complete fluid removal

Causes are typically mineral sediment clogging drainage paths or deteriorating plastic from constant use. This OEM LG replacement pipe restores reliable condensate removal to maintain peak efficiency.

This OEM LG part is also compatible with Sears/Kenmore. 

This adjustable leveling leg assembly supports and stabilizes your appliance by threading into the base frame. Replacing a worn or missing leg helps you level the unit for smoother, quieter operation on uneven floors.

• Provides height adjustment to level the appliance and distribute weight evenly
• Helps prevent rocking, wobbling, and excess vibration or rattling
• Can improve door alignment and smooth opening/closing when the cabinet is properly leveled
• Useful when a leg is missing, damaged, or threads are stripped

• Disconnect power; if applicable, shut off the water supply
• Use a helper to safely brace or tip the unit; protect flooring when accessing the leg
• Unthread the old leg and hand-thread the new one; tighten as needed
• Adjust front-to-back and side-to-side until stable; all legs bear weight evenly

This is a refrigerator shelf assembly that provides a stable, easy-to-clean surface for storing food and organizing items inside the fresh food compartment. Replacing a damaged or missing shelf restores usable space and proper support.

• Supports food items and containers on a rigid, flat surface
• Helps maintain organized storage and visibility in the compartment
• Replace if the glass is cracked, frame is broken, or shelf sags/doesn't seat properly
• Can also address rattling or instability from a warped or damaged shelf

• Unplug the appliance or disconnect power before servicing
• Remove contents and carefully lift out the old shelf
• Align the new shelf with the side rails and fully seat it in the supports
• Handle glass with care; avoid impact and uneven pressure during installation

This shelf net is a replacement refrigerator shelf organizer that helps keep items secure and prevents small or loose items from shifting during door opening. It restores the original containment function of the shelf area. What it does:

• Provides a flexible barrier to hold bottles, jars and small containers in place on a shelf or door bin
• Replaces torn, stretched or missing shelf netting that allows items to fall or move
• Restores the designed containment and improves everyday access to frequently used items
• Fits in the shelf frame to provide lightweight, visible storage without blocking airflow

• One shelf net

• Remove the existing damaged net and clean the shelf frame area before installing
• Snap or clip the net into the shelf/frame slots; no special tools typically required
• Handle carefully to avoid overstretching; ensure clips or tabs fully engage for secure fit
• Disconnect power only if removing shelves near electrical components or light assemblies

This refrigerator shelf provides a stable, easy-to-clean surface for storing food and containers inside the fresh food compartment. It restores usable storage and helps keep items organized and visible. What it does

• Replaces a cracked, chipped or missing shelf so refrigerated items sit level and secure.
• Restores a smooth, easy-to-clean surface that resists spills and stains.
• Slides into existing shelf supports to maintain adjustable storage layout.
• Helps prevent items from falling through or shifting during normal use.

• Remove food and containers before replacing the shelf.
• Handle glass shelves with care; wear gloves to reduce risk of cuts.
• Align shelf edges with the cabinet rails or supports and slide into place until seated.
• Do not force the shelf; check that supports are intact and properly aligned before loading.

This replacement shelf assembly restores usable storage space and provides a stable surface for food and containers in the refrigerator. It's a direct-fit shelf designed to match the original form and function for easy restoration. What it does:

• Provides a flat, stable shelf surface so food and containers sit level and secure
• Replaces cracked, chipped, or missing shelves that cause items to slide or break
• Restores proper shelving layout to help organize interior storage
• Helps maintain even airflow and access to stored items when positioned correctly

• One shelf assembly

• Remove food and unplug the appliance before beginning any service
• Handle glass or trim sections carefully to avoid chipping or injury
• Slide into the existing shelf supports; no special tools typically required
• Replace shelf clips or supports if damaged before installing the new shelf

The Cover Assembly is an OEM part for LG French door refrigerators equipped with integrated television screens. This cover protects the television when not in use.

Symptoms of a bad cover assembly include: 

• Cracked, clouded, or peeling finish reducing aesthetics
• Poor fit allowing dust entry near television components  
• Binding or getting stuck when opening and closing
• Hinges, pins, or latches weakened through repeated use

Causes of failure can be temperature cycling absorbing and releasing moisture daily, over-extension through careless opening/closing, or general wear from constant daily usage.

Replace yours today with this genuine OEM LG cover assembly to restore your refrigerator's integrated display features. A snug fit around the television combined with a durable surface protects against spills for reliable entertainment access. This replacement part is also compatible with KitchenAid, Samsung, and GE refrigerators featuring television modules.

This is a refrigerator shelf assembly that provides a stable, easy-to-clean surface for storing food and organizing items inside the fresh food compartment. Replacing a damaged or missing shelf restores usable space and proper support.

• Supports food items and containers on a rigid, flat surface
• Helps maintain organized storage and visibility in the compartment
• Replace if the glass is cracked, frame is broken, or shelf sags/doesn't seat properly
• Can also address rattling or instability from a warped or damaged shelf

• Unplug the appliance or disconnect power before servicing
• Remove contents and carefully lift out the old shelf
• Align the new shelf with the side rails and fully seat it in the supports
• Handle glass with care; avoid impact and uneven pressure during installation

This is a refrigerator shelf assembly that provides a stable, easy-to-clean surface for storing food and organizing items inside the fresh food compartment. Replacing a damaged or missing shelf restores usable space and proper support.

• Supports food items and containers on a rigid, flat surface
• Helps maintain organized storage and visibility in the compartment
• Replace if the glass is cracked, frame is broken, or shelf sags/doesn't seat properly
• Can also address rattling or instability from a warped or damaged shelf

• Unplug the appliance or disconnect power before servicing
• Remove contents and carefully lift out the old shelf
• Align the new shelf with the side rails and fully seat it in the supports
• Handle glass with care; avoid impact and uneven pressure during installation

Restore organized storage with this fresh room tray assembly for your refrigerator. It replaces a cracked or missing deli/fresh drawer so items slide smoothly and stay easy to see and reach.

• Creates the fresh room/deli drawer storage area in the refrigerator compartment
• Slides on the existing rails for smooth access to stored items
• Helps keep items contained and organized
• Replaces a cracked, warped, or missing drawer that won't slide or stay in place

• Remove the old drawer by pulling it out and lifting/tilting as your model's diagram shows; install by aligning with the rails and sliding in until fully seated
• Handle plastic carefully; do not force into place to avoid stress cracks
• No tools typically required; disconnect power only if working near electrical components

This tray cover replaces a damaged or missing appliance tray cover to restore a clean appearance and proper containment of spills. It fits into the existing tray location and helps keep interior surfaces protected during normal use. What it does:

• Covers the appliance tray to help contain spills, crumbs, and minor debris
• Maintains a finished look and helps prevent direct contact with the underlying tray
• Supports proper placement of removable trays or components that sit above it
• Useful when the original cover is cracked, warped, or otherwise compromised

• One replacement tray cover

• Basic snap-in or screw-in installation; confirm orientation before fastening
• Power off and unplug the appliance before attempting any service
• Use gentle pressure to avoid cracking the new cover; do not force damaged fasteners
• Replace missing or damaged screws or clips with OEM-specified hardware

The Deli Drawer Front Cover is an OEM part for LG refrigerators. It provides an attractive facia that protects the internal components of the deli drawer. This cover is designed to integrate with the style and finish of the refrigerator interior. 

Symptoms of a bad Deli Drawer Front Cover include: 

• Cracks, chips, or other visible cosmetic damage
• Discoloration that detracts from the aesthetics  
• The cover is loose, misaligned, or missing
• Difficulty opening or closing the deli drawer

Causes of a bad cover can be normal wear and tear over time from repeated use, as well as accidental drops or impacts that cause cracks or breaks.

This OEM replacement part is also compatible with select LG models.

This decor assembly is the outer trim that surrounds the appliance control panel, restoring the unit's finished appearance and protecting the controls from everyday wear. It replaces cracked, scratched or faded trim to make the front look like new. What it does

• Covers and protects the control area from spills, scratches and cosmetic damage
• Restores the appliance's factory appearance after impact or deterioration
• Helps keep buttons and touch controls clear of debris and grime
• Required to properly seat or secure the control components it surrounds

• One decor assembly (control-panel trim) as pictured

• Disconnect power (unplug or shut off breaker) before starting work
• Remove any retaining screws or clips from the control panel; handle trim gently to avoid breaking tabs
• Reuse existing fasteners unless new hardware is explicitly listed as included

This vegetable tray assembly replaces the crisper drawer that stores fruits and vegetables, restoring organized storage and easy access in the refrigerator. Durable plastic construction supports produce while sliding smoothly on its track. What it does:

• Holds and organizes fruits and vegetables in the refrigerator produce zone
• Provides a removable drawer for easy loading, cleaning, and access to food
• Restores proper fit and sliding function when a cracked or broken drawer causes sticking or poor alignment
• Helps contain spills and keeps produce separated from other fridge shelves

• Remove food and empty drawer before attempting replacement
• Typically slides into tracks; lift slightly to disengage and slide out, reverse procedure to install

This Vegetable Tray Assembly is the removable crisper drawer that stores fruits and vegetables to help keep them organized and contained inside the refrigerator. Durable plastic construction restores a proper storage area and drawer function. What it does:

• Replaces a cracked, warped, or broken crisper drawer to restore proper storage and containment
• Provides a dedicated tray for fruits and vegetables to keep items separated from main shelves
• Slides into refrigerator tracks to allow smooth opening and closing of the drawer
• Helps prevent leaks and spills from spreading to interior shelves when intact

• Remove all food and empty the cabinet area before replacing the tray
• Generally slides in/out of tracks; lift slightly to remove if drawer is jammed
• Inspect tracks and guides for damage and clean debris before installation
• Use caution when handling edges

This LED assembly replaces a TV backlight module to restore even screen illumination and image brightness. It mounts behind the LCD panel and provides the LED sources that light the display. What it does:

• Replaces a damaged or failed TV backlight module
• Restores even screen brightness and reduces dark spots
• Helps resolve flickering, dim display, or no-picture issues related to the backlight
• Works as a direct-fit LED module for compatible LG LCD TVs

• One LED assembly

• Disconnect power and remove the TV from power source before beginning service
• Requires partial disassembly of the TV (front bezel and LCD panel removal); handle the panel and LEDs carefully
• Avoid touching LED surfaces and circuit traces; use ESD precautions and appropriate tools

This Tray Cover Assembly replaces a damaged or missing cover on the appliance tray to help contain contents and keep the tray functioning correctly. It restores the tray's protective surface and helps prevent spills or contamination. What it does:

• Covers and protects the tray surface to keep contents contained
• Helps direct contents into the tray area to reduce spills
• Replaces cracked, warped or broken covers that no longer seat properly
• Restores a flush fit and appearance for the tray area

• One tray cover assembly

• Disconnect power to the appliance before beginning any service
• Remove the tray or access panel per your model's service instructions to access mounting points
• This part typically snaps or slides into place; light tools (screwdriver) may be needed to remove retaining clips

This rail guide assembly keeps a refrigerator drawer aligned and sliding smoothly so you can open and close it without sticking or sagging. It restores proper drawer support and alignment for reliable everyday use. What it does:

• Supports the drawer on its track so the drawer slides in and out evenly
• Guides movement to prevent binding, sticking, or uneven operation
• Helps reduce noise from rubbing or misaligned drawer slides
• Restores proper drawer height and prevents sagging or catching

• Remove all contents from the drawer before beginning work
• Use basic hand tools; handle plastic parts gently to avoid cracking
• Reassemble drawer and test smooth operation before returning items to the drawer
• If the drawer is heavy or awkward, get help to avoid dropping the drawer or injuring yourself

This guide rail assembly keeps a refrigerator or freezer drawer aligned and sliding smoothly so you can open and close drawers without sticking or tilting. Replaces worn or damaged rails to restore proper drawer function and support. What it does:

• Supports and guides a refrigerator or freezer drawer along its track for smooth movement
• Prevents drawer tilt or sag that can cause binding or uneven closing
• Helps maintain proper load alignment so shelves and drawers operate reliably
• Commonly replaced when drawer scraping, sticking, or misalignment occurs

• One guide rail assembly as shown

• Basic hand tools required; disconnect power before working near electrical components
• Remove the drawer and follow OEM disassembly steps to access rail mounting points
• Inspect mating slides and mounting clips; replace any damaged hardware for best fit

This replacement door gasket creates a heat-resistant seal between the oven door and the front frame. A tight seal helps the oven maintain temperature and cook evenly while keeping heat from escaping into the kitchen.

• Seals the oven cavity to reduce heat loss and temperature fluctuations
• Helps improve preheat times and baking performance
• Worn seals can cause heat leakage, longer cook times, or hot air felt around the door
• Cracks, flattening, or fraying indicate the gasket should be replaced

• Disconnect power before servicing; allow the oven to cool completely
• Open the door and carefully release the old gasket from its mounting clips
• Align and press the new gasket into the channel, seating each clip fully
• After installation, check for even contact around the door

Replacement door gasket that seals the refrigerator door to help keep cold air in and warm air out, reducing frost and cold-air leaks and helping the appliance maintain consistent internal temperatures for food preservation. What it does:

• Creates an airtight seal around the refrigerator door to minimize cold-air loss
• Helps prevent frost buildup in the fresh-food compartment and freezer-adjacent areas
• Addresses symptoms like visible cracks, tears, gaps, or cold air escaping from the door edges
• Helps the fridge maintain set temperatures and can reduce the workload on the cooling system

• Disconnect power to the appliance before starting any repair
• Remove the old gasket fully and clean the door channel to ensure a proper new seal
• Press the new gasket into the channel evenly, working around the perimeter and checking for full contact
• After installation, close the door and inspect the seal; allow a short settling period and re-check for gaps

This door gasket seals the dishwasher door perimeter to keep water and steam inside the tub. Replacing a worn or flattened seal helps stop leaks and restores a consistent, reliable door closure. What it does:

• Forms a watertight seal between the door and tub during wash cycles
• Helps prevent leaks from the sides or bottom of the door
• Replace if the gasket is cracked, torn, deformed, or no longer springy
• Can help with symptoms like water on the floor at the front of the unit or difficulty latching the door

• Includes 1 door gasket

• Disconnect power and shut off the water supply before servicing
• Open the door, pull the old gasket straight out of the channel, and clean the groove
• Let the new gasket warm to relax kinks; start at the top center and press evenly into the channel down both sides—fully seat the corners and avoid stretching
• Close the door to help the seal set, then run a short cycle and check for leaks

This Hinge Cover Assembly protects and conceals the door hinge area, restoring a clean appearance and preventing dirt or loose clothing from catching in the hinge. Fits where a cosmetic or protective hinge cover is needed. What it does:

• Covers the door hinge to shield moving hardware from debris and reduce pinching hazards
• Restores a finished look to a damaged or missing hinge area
• Helps keep lint, dust and small objects away from the hinge mechanism
• Can reduce noise caused by exposed hinge components when intact

• One Hinge Cover Assembly as shown

• Intended for drop-in replacement; follow your appliance's service manual for disassembly steps
• Disconnect power and water before starting any repair
• Handle plastic parts carefully to avoid cracking; use appropriate fasteners and torque per OEM guidance
• If hinge or mounting hardware is damaged, replace those components before installing the cover

This hinge cap covers and protects the door hinge, keeping the hinge assembly clean and improving the appliance's appearance. It replaces a cracked, missing, or worn hinge cover to help doors operate smoothly and look finished. What it does:

• Covers the door hinge to protect mating surfaces from dirt and damage
• Hides hinge hardware for a cleaner, finished look
• Helps prevent debris from interfering with hinge movement
• Can resolve cosmetic issues and reduce risk of snagging on exposed hinge parts

• One hinge cap

• Remove power and open the door to a safe, supported position before starting
• Typically snaps or screws onto the hinge—retain original fasteners unless replacement required
• Inspect hinge and fasteners while installing; replace any damaged hardware

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

This replacement home bar case is the inner door shelf that holds bottles and small items in the refrigerator door, restoring storage function and a finished interior look. It fits the refrigerator's dedicated home/bar compartment. What it does:

• Provides a secure shelf for bottles, cans, and small containers in the door's home/bar area
• Restores proper spacing and support so items sit level and stay in place
• Replaces cracked, broken, or missing door-shelf housings that cause items to fall or rattle
• Helps maintain the refrigerator's intended interior organization and appearance

• One home bar case (single inner door shelf housing)

• Remove food and items from the door before replacing; handle glass or plastic shelves carefully
• Usually installs with snap-in tabs or a small number of screws—do not force parts; align tabs before pressing
• If your door has wiring or lighting nearby, disconnect power to the refrigerator before working on the door

This replacement home bar door gasket creates an airtight seal around the refrigerator's beverage/access compartment to help maintain cold temperatures and reduce drafts and moisture buildup. What it does:

• Seals the home bar/door compartment to help keep cold air in and warm air out
• Reduces condensation, frost buildup and temperature fluctuations in the compartment
• Helps prevent spoiled items and improves cooling efficiency when functioning properly
• Addresses symptoms like visible gaps, air leaks, excess moisture, or a door that won't close tightly

• Clean the door channel and gasket seating area of debris and old adhesive
• Press the gasket evenly into the channel, working around the door to ensure full contact
• Test the door for an even seal and adjust as needed; unplug refrigerator only if required for access or safety

The refrigerator door gasket seals the gap between the door and cabinet to keep cold air in and humid air out, helping maintain temperature, reduce frost and condensation, and restore a tight, reliable door close.

• Creates an airtight perimeter seal to prevent warm air leaks
• Helps stabilize interior temperature and humidity
• Minimizes frost buildup and condensation around the door
• Common symptoms: torn or deformed seal, door not sealing, moisture/frost near door, rising temps

What's included: 1 door gasket Installation notes:

• Disconnect power before servicing
• Allow the new gasket to warm to room temperature; soften in warm water or with gentle, low heat to relax folds
• Remove the old gasket and thoroughly clean the mounting channel/mating surfaces
• Seat the new gasket starting at the corners, then along the sides; ensure it's fully engaged and even all around, and check door alignment/seal

Restore a tight, reliable seal on your refrigerator door with this replacement gasket. A fresh gasket stops cold-air leaks that lead to frost, condensation, and temperature swings—helping your fridge run smoothly and keep food at the right temperature. What it does:

• Seals the gap between the door and cabinet to keep cold air in and warm air out
• Helps maintain consistent interior temperature and humidity
• Reduces frost and condensation around the door opening
• Common symptoms: torn or warped gasket, door not closing flush, moisture at the seal, frost buildup, or the unit running more than usual

• 1 door gasket

• Disconnect power before starting and clear items from the door
• Lay the new gasket flat and gently warm it (hot water or low-heat hair dryer) to relax folds
• Starting at the corners, press the gasket lip fully into the door channel and work evenly around
• Perform a paper-slip test around the perimeter and adjust door alignment if needed; avoid overheating the gasket

The Refrigerator Flipper Assembly is an OEM part for LG refrigerators. This assists in the smooth opening and closing of the refrigerator door. It ensures an airtight seal when the door is closed, preventing cool air from escaping and maintaining the refrigerator's internal temperature. 

Causes of a malfunctioning Refrigerator Flipper Assembly can range from physical damage, such as cracks or breakage, to wear and tear from regular use.

Symptoms of a bad Refrigerator Flipper Assembly include:

• Difficulty in opening or closing the refrigerator door
• A noticeable gap when the door is supposed to be sealed shut
• Increased energy consumption as the refrigerator works harder to maintain its temperature
• Spoilage of food items quicker than expected due to poor temperature regulation

This OEM LG part is also compatible with some Kenmore models.

This replacement drawer guide restores proper tracking and smooth operation to a refrigerator or freezer drawer. It helps keep the drawer aligned and reduces scraping, sticking, or uneven movement for reliable daily use. What it does:

• Guides the drawer along its track so it opens and closes smoothly
• Replaces a worn, cracked, or bent guide that can cause sticking or misalignment
• Reduces drawer rattling and scraping against the cabinet
• Helps prevent drawer drops or catching when pulling open or pushing closed

• Unplug the appliance or switch off power before servicing to avoid electrical hazards
• Remove the drawer and any screws or retaining clips holding the old guide; keep hardware if it's reusable
• Align the new guide on the track and secure with the original screws or clips; do not force parts into place
• Test the drawer operation before returning contents; recheck alignment and hardware if movement is still obstructed

This replacement cap cover provides the finished trim and a protective snap-on cover for the appliance component. It restores a clean appearance and helps protect the underlying hardware from dust and debris. What it does

• Covers and protects exposed hardware or openings to prevent dust, lint, and debris buildup
• Restores the appliance's finished appearance after a cracked or missing cover
• Helps keep adjacent parts secure and reduces rattling from loose trim
• Fits as a direct replacement designed to snap into the existing mounting points

• One cap cover

• Turn off power to the appliance before starting disassembly to avoid injury
• Usually installs by snapping into place; remove any trim or panels that obstruct access
• Use gentle, even pressure to avoid cracking the new cover; plastic pry tools can help
• If mounting clips are broken, they may need replacement for a secure fit

This replacement door basket restores usable storage space on the refrigerator door, holding bottles, jars and small containers so food stays organized and easy to reach. Made to match the original fit and mounting points. What it does:

• Replaces a cracked, broken or chipped door basket that can no longer hold items securely
• Restores proper storage and keeps bottles and containers from shifting or falling
• Replaces missing or warped bins that prevent the door from sealing or organizing contents
• Compatible with factory mounting clips and shelf support locations

• Remove all food and loose items from the door before installing the new basket
• Most door baskets snap into place on molded supports; align tabs and press until secured
• Inspect mounting clips or supports for damage; replace clips if they are broken

This door basket is the refrigerator door bin that mounts on the inner door panel. Replacing a cracked, loose, or missing bin restores safe, organized storage for bottles, condiments, and other small items on your refrigerator door.

• Provides stable door storage for condiments, beverages, and small items
• Attaches to molded tabs/rails on the door liner
• Restores capacity and organization when the original bin is damaged or missing
• Common symptoms: bin falls off, won't stay seated, wobbles, or is cracked

• Remove contents, then lift the old bin straight up to release from the door tabs
• Align the new bin with the door rails/tabs and press down until fully seated
• Handle plastic at room temperature and avoid forcing to prevent cracking
• Confirm secure engagement before reloading items

Replacement refrigerator door basket that restores usable storage on the door and keeps bottles, jars and condiments secure. Molded plastic design replaces a cracked or broken bin so items stay organized and won't fall when the door opens. What it does

• Provides a shelf on the refrigerator door to hold bottles, jars and small containers
• Replaces cracked, chipped or warped door bins that no longer secure items
• Helps prevent spills and shifting items when opening or closing the door
• Use only on compatible models; fit with your model number before ordering

• Remove all items from the door and lift or slide out the old basket
• Install the new basket by aligning tabs/runners and snapping it into place; do not force
• Inspect mounting tabs—if damaged, replacement may require additional clips
• Dispose of broken plastic pieces carefully and keep children away during replacement

The door basket is an OEM part for LG refrigerators. It is the basket located inside the refrigerator or freezer door that provides storage for smaller items like condiments, spreads, or snacks. The basket measures approximately 12" width x 3 1/4" height x 3 1/4" depth. 

Symptoms of a bad basket include:

• The door basket being loose, cracked, or damaged
• Difficulty removing or replacing the basket 
• Reduced storage capacity due to a warped or broken basket

Causes of a bad door basket can be normal wear and tear over time, exposure to excessive weight that stresses the plastic material, or accidental damage from dropping or impact.

This OEM LG part is also compatible with select Sears/Kenmore models.

This stopper assembly cushions and limits the door travel to prevent slamming and ensure correct door alignment. It restores smooth, controlled closing and helps reduce noise and wear on the door hinge area. What it does:

• Absorbs door impact to prevent hard slams and reduce noise
• Keeps the door from overtravel for consistent alignment
• Helps protect hinge and cabinet edges from damage
• Restores proper door closing feel when worn or broken

• One stopper assembly as shown

• Disconnect power and empty door area before starting repairs
• Access may require removing door trim or inner panel
• Use basic hand tools; avoid forcing the part into place to prevent damage

Lower hinge assembly that supports the refrigerator door and provides a secure pivot point for smooth opening and closing, helping maintain proper door alignment and seal. What it does:

• Provides the pivot and support for the bottom of the refrigerator door to open and close smoothly.
• Keeps door aligned to help maintain an effective seal and reduce gaps that can cause cooling loss.
• Prevents door sag and uneven wear on the door and cabinet when functioning correctly.
• Addresses symptoms such as a crooked or dragging door, rubbing at the gasket, or noisy pivoting.

• Unplug the appliance and remove food and shelving from the door before beginning work.
• Support the door securely while removing the old hinge to avoid damage or injury.
• Keep original mounting hardware—replace with manufacturer hardware if needed.

This bushing is a replacement shaft support that stabilizes a rotating assembly and helps reduce wear and noise. It restores smooth movement and helps maintain proper alignment for the appliance component. What it does

• Supports and centers a rotating shaft or drum to reduce wobble and rubbing
• Reduces noise and friction from worn pivot or support points
• Helps prevent uneven wear on mating parts and prolongs assembly life
• Commonly replaced when you hear squeaking, grinding, or notice excessive play

• One bushing

• Inspect mating surfaces and replace any damaged clips, seals, or fasteners as needed
• Use basic hand tools; hold the assembly steady and press the bushing squarely into place
• If the bushing is press-fit, use a suitable driver or press to avoid damage
• Disconnect power and follow all safety precautions before beginning repairs

This door stopper mounts at the hinge to limit the refrigerator door's opening angle and provide a positive stop. Replacing a worn stopper helps protect the hinge, prevent over-swing, and promote a smooth, even door seal.

• Limits door opening at the hinge to prevent overextension
• Helps maintain door alignment and consistent gasket contact
• Reduces impact that can loosen hinges or damage the cabinet
• Common symptoms: door swings too far, clunks at full open, doesn't stop smoothly, or shows visible wear at the stop

• Disconnect power and remove items from the door to reduce weight
• Support the door; remove hinge cover and fasteners as needed to access the stopper
• Install the new stopper in the same orientation; tighten hardware securely
• Verify door swing and sealing after reassembly

The Lower Refrigerator Door Hinge is an OEM part for LG refrigerators. This hinge supports the refrigerator door, allowing it to open and close smoothly while maintaining proper alignment. It is designed to handle the weight of the door and ensure a secure and stable operation over time.

Causes of a bad lower refrigerator door hinge can include regular wear and tear, physical damage from overloading or impacts, and gradual loosening over time. A faulty hinge can lead to misalignment, difficulty in opening or closing the door, and potential damage to the door seal.

Symptoms of a bad lower refrigerator door hinge include:

• The door not closing properly or staying open
• Sagging or misaligned door
• Unusual noises when opening or closing the door
• Gaps in the door seal, causing cooling inefficiency

This OEM LG part is also compatible with Sears/Kenmore models.

This refrigerator door handle assembly replaces a broken, cracked or loose door pull to restore a secure grip and normal door use. Durable finish matches the original for a clean, factory look. What it does:

• Replaces damaged or worn door handle components so the door can be opened and closed easily
• Stops wobbling, loose fit, or missing grip that can make the door hard to operate
• Restores the original appearance after chips, cracks or impact damage
• Works with the factory mounting points for a secure fit when installed correctly

• Remove contents and secure the door before starting to avoid tipping or injury
• Use basic hand tools; keep fasteners and trim clips for reuse only if undamaged
• Follow manufacturer instructions for alignment and torque to avoid stressing the door

This rail slide replaces a worn or broken drawer track to restore smooth opening and reliable support for a refrigerator or freezer drawer. It helps the drawer glide smoothly and keeps contents stable during use. What it does:

• Guides and supports the drawer for smooth, linear movement
• Restores even alignment to prevent sticking, binding, or uneven travel
• Reduces rattling and helps the drawer stay fully seated when closed
• Addresses symptoms like a sagging, hard-to-pull, or off-track drawer

• High-level replacement — remove the drawer and fasteners to swap the rail
• Keep small screws and clips organized and reuse original hardware unless replacements are provided
• Wear gloves to protect hands and avoid damaging painted surfaces

This slide rail restores smooth, stable drawer or rack movement so the compartment opens and closes without binding. It replaces a worn or damaged rail to improve alignment and support. What it does

• Guides and supports a drawer or oven/rack for even, controlled sliding
• Reduces sticking, scraping, or uneven travel when opening or closing
• Helps prevent the drawer or rack from sagging or coming off the track
• Works as a mechanical replacement when the original rail is bent, cracked, or worn

• One slide rail

• Disconnect power or unplug the appliance before beginning any repair
• Remove the affected drawer or rack to access mounting screws and clips
• Match rail orientation and secure with the original fasteners; do not overtighten
• Test operation after installation and reassemble any removed components

This harness assembly restores the electrical connections between components, replacing a damaged or worn wiring harness to help re-establish reliable power and signal paths for the appliance. What it does

• Replaces a damaged or frayed wire harness that can cause intermittent or no power to components
• Restores factory wiring routes and connector fit to ensure correct electrical signaling
• Prevents shorts or open circuits caused by broken wires or loose terminals
• Helps resolve symptoms like components not powering, erratic operation, or connector damage

• One harness assembly as shown

• Disconnect power and any water supply before starting; confirm appliance is fully de-energized
• Compare connectors and wire lengths to the original part before installation
• Route harness along factory clips and secure fasteners to prevent pinching or chafing

This ice maker gear drives the ejector blades that push ice from the tray into the bin. Replacing a worn or broken gear restores proper harvest cycles and stops grinding or slipping during ejection. What it does:

• Turns the ice maker ejector to release ice cubes during the harvest cycle.
• Stops or reduces grinding noises and slipping when the gear teeth are stripped or damaged.
• Helps restore regular ice production when the ejector no longer rotates.
• Works as the replacement driven gear in compatible LG ice maker gear trains.

• Disconnect power before servicing the ice maker to avoid shock or injury.
• Remove the ice maker assembly to access the gear; follow OEM instructions for disassembly.
• Inspect the mating gear, motor shaft, and ejector assembly for wear—replace additional damaged parts as needed.
• Use the matching part number to ensure fit.

This center hinge assembly replaces the middle door hinge on compatible French-door refrigerators to restore proper door alignment and smooth opening. It helps prevent sagging, binding, and air leaks caused by a worn or damaged hinge. What it does:

• Supports and aligns the upper/lower refrigerator doors for correct sealing
• Enables smooth pivoting of the door to open and close without binding
• Corrects uneven gaps or door sag that can cause cooling loss or excessive wear
• Replaces a bent, cracked, or worn hinge that may cause noisy operation

• One center hinge assembly

• Remove power and empty the door(s) before beginning work; follow manufacturer service instructions
• Use proper tools and support the door while removing/installing the hinge to avoid injury or damage
• Inspect surrounding trim and fasteners; replace any worn screws or bushings as needed

This center hinge assembly replaces the factory door pivot and restores proper door alignment and smooth opening. It supports the refrigerator door at the center hinge point to help stop sagging, binding, or uneven gaps. What it does:

• Replaces the center pivot point that supports and guides the door
• Restores correct door alignment and even sealing to help maintain cooling efficiency
• Reduces door sag, sticking, and noise caused by worn hinge parts
• Allows the door to open and close smoothly when operating normally

• Disconnect power to the appliance and remove food from affected door before starting.
• Support or remove the door to avoid injury or damage; the door can be heavy.
• Use appropriate hand tools and follow torque guidelines in the OEM instructions.

This is a ring intended for use in refrigerators. The ring is used to adjust the height of the door. Genuine OEM replacement rings are necessary for the repair to ensure a proper fitting.If the refrigerator door no longer opens or closes easily, or if it is not sealing properly, the rings may need to be replaced. Visual inspection can determine if there are problems with the refrigerator door rings. Make sure to unplug the device before starting any of the disassemblies of the machine. Wear gloves.This ring is an authentic OEM replacement part. It is sold as an individual unit. The ring is made of high-quality, durable materials. The replacement piece is sourced directly from the manufacturer. It can be installed in several models of refrigerators. The genuine OEM replacement ring is compatible with refrigerators produced by both LG and Kenmore.

The Spanner Wrench is an OEM replacement part for LG refrigerators. This tool allows you to adjust the door hinges to ensure the doors are level and aligned properly. A well-aligned door is crucial for maintaining the internal temperature and efficiency of the refrigerator, preventing energy loss and ensuring food is stored under optimal conditions.

Symptoms that you might need to adjust the door hinges and potentially need this wrench include:

• Doors not closing properly or sealing tightly
• Visible gaps between the door and the main body of the refrigerator
• The refrigerator tilting or not sitting level

This spanner wrench is also compatible with some Sears/Kenmore refrigerators. 

This upper hinge assembly secures and guides the appliance door at the top hinge point, restoring proper door alignment and smooth opening. Replaces a worn or damaged upper hinge to reduce door sag, binding, or uneven sealing. What it does:

• Supports the top of the door and provides the pivot point for opening and closing
• Restores correct door alignment to improve gasket sealing and energy efficiency
• Eliminates rubbing, binding, or uneven movement caused by a damaged hinge
• Reduces noise from a loose or worn hinge

• Unplug the appliance and empty or support the door before starting work
• Use proper hand tools and take care not to tighten fasteners excessively
• Keep track of hardware; replace only listed items unless additional parts are required

This upper hinge assembly secures and guides the refrigerator door at the top, restoring proper alignment and smooth opening. Replace a worn hinge to stop sagging doors and improve sealing and operation. What it does:

• Provides the top pivot point for the refrigerator door, keeping it aligned during opening and closing
• Restores proper door clearance and prevents rubbing or misalignment
• Helps maintain a tight door seal to reduce cold air loss
• Addresses symptoms like a sagging or uneven door, noisy movement, or difficulty closing

• Disconnect power to the appliance before beginning repairs to prevent injury.
• Support the door while removing and installing the hinge to avoid dropping or damage.
• Use appropriate hand tools; do not overtighten fasteners to prevent stripping.

This upper hinge assembly supports the refrigerator door at the top, providing a smooth pivot and proper alignment. Replacing a worn hinge restores even gaps and a tight seal to help maintain consistent cooling performance.

• Supports the door's weight and provides the top pivot point
• Maintains alignment for correct gasket compression and a tight seal
• Helps the door open and close smoothly without rubbing or binding
• Common signs of wear: door sagging or misalignment, rubbing/clicking noises, and poor sealing or condensation around the gasket

• Unplug the refrigerator before servicing.
• Remove the top hinge cover; retain screws and any shims for reuse.
• Support the door with a helper while removing and installing the hinge.
• Position the new hinge, align the door, then tighten screws and verify smooth swing and full gasket contact all around.

This replacement spring restores proper tension to a microwave oven door hinge so the door opens and closes smoothly and holds position. It's a direct-fit part that helps eliminate sagging or uneven door movement. What it does

• Replaces a worn or broken hinge spring to restore proper door tension and alignment
• Helps prevent door from dropping open or not staying closed securely
• Supports smooth, controlled door opening and closing motions
• Addresses symptoms such as a sagging door, uneven closing, or loose-feeling hinge

• One replacement hinge spring (quantity: 1)

• Disconnect power to the appliance before attempting any service to avoid electrical shock
• Access may require removing the outer door panel or control panel; follow OEM disassembly instructions
• Handle the spring carefully—springs can be under tension and may release suddenly

The Door Handle Holder Assembly is an OEM replacement part for LG refrigerators. It contains the internal brackets and mounting hardware required to securely attach the refrigerator door handles.

Causes of a faulty door handle holder assembly include wear from years of use, broken or stripped screws, or cracks in the plastic from heavy pulling or slamming.

Symptoms of a problematic door handle holder assembly are:

• Loose, wobbly or disconnected door handles  
• Difficulty opening the refrigerator door 
• Handles that do not stay flush or feel secure

This OEM LG replacement is compatible with select Kenmore side-by-side refrigerator models as well.

This door magnet is the magnetic gasket strip that helps the door close securely and maintain an airtight seal, improving cooling efficiency and preventing leaks or temperature loss. What it does:

• Restores the magnetic attraction in the door seal so the door stays closed
• Helps maintain proper internal temperature by providing an airtight seal
• Reduces frosting, condensation, and energy waste caused by a weak or damaged seal
• Common symptom: door not sealing or closing firmly

• Disconnect power to the appliance before starting any repair
• Remove the door gasket or trim per the service manual to access the magnet strip
• Press or seat the magnet strip into the gasket channel; some models may require adhesive or fasteners—refer to OEM instructions

The Compressor is an OEM component specifically designed for LG refrigerators. Located inside the refrigerator compartment, the compressor pressurizes and circulates refrigerant through the cooling system. Through precisely timed operation, the compressor maintains optimal freshness.

Symptoms of a bad compressor include:  

• Elevated interior temperatures failing to efficiently chill
• Loud buzzing or vibrating noises coming from inside the walls  
• Frost buildup indicating ineffective cooling cycles
• Complete cooling system failure leaving foods unpreserved

Causes involve refrigerant leaks, blocked airflow to the compressor, or simply wear over tens of thousands of hours of use breaking down moving components.

This OEM LG part is also compatible with some refrigerator models from Kenmore and Sears. Replace to restore reliable, long-term temperature control keeping contents at peak freshness.

This motor support damper sits between the refrigerator's compressor and base to absorb vibration and movement. Replacing a worn damper helps quiet rattles and humming from the back of the cabinet and keeps the compressor properly supported.

• Cushions the compressor to reduce transmitted vibration and noise
• Helps quiet humming, buzzing, or rattling from the lower rear of the refrigerator
• Maintains proper compressor alignment and support on the base pan
• Common signs of wear: increased vibration/noise, a cracked or flattened damper, or noticeable compressor movement when running

• Unplug the refrigerator and pull it forward to access the rear; allow the compressor to cool before working
• Support the compressor to remove load from the mount before loosening hardware
• Replace the damper and tighten mounting hardware evenly without over-compressing the rubber
• Avoid bending or stressing refrigerant tubing; wear gloves and eye protection

This Front Cover Assembly replaces a damaged or worn front panel to restore the appliance's appearance and protect internal components. It provides a secure, finished surface around the door and control area for safe, reliable use. What it does:

• Replaces cracked, scratched, or broken front panel material that affects appearance and fit
• Protects internal components and wiring from debris and moisture
• Restores proper alignment and sealing around the door/control area
• Helps reduce vibration-related rattles caused by a loose or damaged front panel

• One Front Cover Assembly

• Disconnect power (and gas supply if applicable) before starting any work
• Removal typically requires unscrewing fasteners and releasing retaining clips; keep track of all hardware
• Support the cabinet/front panel during removal and installation to avoid dropping or pinching wiring
• Test the appliance after installation to ensure secure fit and normal operation

This compressor damper is a vibration-isolating mount that sits between the sealed-system compressor and the chassis. It cushions the compressor to reduce noise, limit vibration transfer, and help keep refrigerant lines from being stressed.

• Isolates the compressor from the frame to absorb start/stop shock and vibration
• Helps reduce humming, rattling, or buzzing from the back/bottom of the appliance
• Replaces a damper that's cracked, flattened, hardened, or missing
• Can help if the compressor rocks or the unit vibrates excessively

• Disconnect power and pull the unit forward for access; remove rear/service panel if present
• Support the compressor to relieve load on the mounts before removing fasteners
• Match orientation; transfer any sleeves/spacers from the old damper to the new one
• Ensure the compressor sits level and that tubing is not strained before restoring power

Replacement front cover that restores your appliance's exterior finish and helps protect controls and internal components from everyday wear, spills, and minor impacts, delivering a clean, finished look and proper front-panel fit. What it does:

• Covers and protects the appliance's front area, helping shield controls and wiring from dirt and moisture.
• Restores damaged or cracked front trim for improved appearance.
• Helps maintain proper alignment and fit of the front assembly.
• Common symptom: cracked, chipped, warped, or loose front panel that exposes internal parts or looks worn.

• Disconnect power (unplug or switch off breaker) before starting any repair.
• Basic hand tools (screwdriver set) may be required to remove the old cover and install the replacement.
• Handle edges carefully to avoid cuts; align tabs/clips and secure fasteners snugly but do not overtighten.

This small stopper installs in the refrigerator to limit the travel of a moving component and keep it securely in place. Replacing a broken or missing stopper prevents over-extension and helps maintain smooth, aligned operation.

• Limits the range of motion for a door, bin, or drawer to prevent over-opening or accidental removal
• Helps keep interior components aligned and operating smoothly
• Replace if cracked, missing, or deformed
• Common symptoms: drawer or bin slides out too far, door swings past normal range, or a broken plastic stop is found

• Disconnect power before servicing; remove or support the affected bin/drawer/door
• Note the old stopper's orientation and location before removal
• Transfer and reuse any original screws or clips if applicable
• Snap or fasten the new stopper in place and test for smooth movement

A small retaining pin used to secure moving parts and keep components aligned for smooth operation. Replacing a worn or broken common pin can stop rattling and restore proper fit between linked parts. What it does:

• Holds or aligns two parts together so they move correctly and stay in position
• Helps prevent rattling, looseness, or parts slipping out of place
• Works as a simple mechanical fastener—no electronics involved

• One common pin

• Disconnect power to the appliance before beginning any service
• Keep track of small parts; lay out components in order to aid reassembly
• May require removal of trim or a hinge/retainer to access the pin—use basic hand tools
• If the pin is difficult to seat, do not force; inspect mating parts for damage

This cabinet roller supports the refrigerator and lets the unit roll in and out of place for cleaning or service. Replace a worn or broken roller to restore smooth movement and help keep the appliance properly positioned.

• Supports the base of the refrigerator and enables rolling movement
• Helps with safe positioning and service access without dragging
• Common failure signs: appliance is hard to move, scraping or rolling noises, a flat-spotted/cracked wheel, or a wheel that won't turn
• Replace when the roller is damaged, seized, or missing

• Disconnect power and shut off water supply; protect flooring before moving the appliance
• With help, pull the refrigerator forward and safely support it to access the roller
• Remove mounting fasteners, install the new roller, and reuse original hardware
• Confirm level and smooth movement before returning the unit to its location

This restrainer is a small retaining clip that helps secure moving or removable components in place, reducing rattles and keeping parts aligned for reliable operation. It's a simple replacement for worn or broken clips. What it does:

• Holds a cover, panel, or door-related component in proper position to prevent shifting
• Reduces noise caused by loose or vibrating parts
• Restores original fit where a broken or missing clip allows movement
• Simple mechanical function — no electrical connections or calibration

• One restrainer

• Disconnect power (and water if applicable) before beginning repairs
• Inspect surrounding mounting points for damage; replace any broken tabs or fasteners
• Typically installs with basic hand tools; align clip and press or snap into place until secure

The Drier Assembly is an OEM part for LG refrigerators. This part removes moisture and contaminants from the refrigerant, ensuring the system operates efficiently and effectively. The drier assembly helps maintain the proper function of the compressor and other cooling components, contributing to the longevity and performance of the refrigerator.

Causes of a bad drier assembly can include clogs from debris, wear and tear over time, or contamination from moisture or refrigerant leaks.  

Symptoms of a bad drier assembly include:

• The refrigerator not cooling properly
• Frost or ice buildup on the evaporator coils
• Increased noise from the compressor
• Reduced efficiency and higher energy consumption
• You should replace the drier assembly if it becomes faulty or damaged.

This OEM LG part is also compatible with select Sears/Kenmore models.

This holder is a small mounting bracket used to secure internal components in place, helping keep parts aligned and stable for reliable operation. It provides a direct, OEM-compatible replacement to restore proper fit and function. What it does

• Secures and supports nearby components to prevent shifting or vibration.
• Restores proper alignment where a worn or broken holder causes rattling or loose parts.
• Helps maintain normal operation by keeping assemblies seated correctly.
• Works behind panels or inside assemblies where a dedicated bracket is required.

• One holder/mounting bracket as shown.

• Installation generally requires removing the panel or access cover where the holder is located.
• Use proper fasteners shown in your appliance; replace any damaged screws or clips as needed.
• Disconnect power before servicing electrical appliances to reduce shock risk.

This condenser assembly connects and secures the refrigerator condenser components, helping the cooling system run reliably. It replaces damaged or corroded condenser wiring to restore proper condenser function and airflow. What it does:

• Provides the OEM-configured wiring and mounting for the condenser to ensure consistent electrical connection.
• Restores proper condenser operation when original wires are cut, burnt, corroded, or loose.
• Helps prevent intermittent cooling or compressor issues caused by faulty condenser connections.
• Maintains correct routing and strain relief for condenser lines to reduce wear and chafing.

• One condenser assembly with attached wiring and mounting hardware as shown.

• Recommended for technicians or confident DIYers; disconnect power before starting and unplug the appliance.
• Inspect surrounding components for damage; replace any compromised parts.
• Use proper tools and tighten mounting hardware to OEM torque where specified; avoid pinching wires.

The Evaporator Fan Blade is an OEM replacement part for LG refrigerators. It is a key component located inside the refrigerator that works to circulate cold air evenly throughout. The fan blade spins rapidly to distribute chilled air from the evaporator coil and refrigeration system, ensuring proper airflow and consistent temperatures across all shelves and compartments.  

Symptoms of a bad evaporator fan blade include:

• Inconsistent or improper interior cooling temperatures 
• Hot or warm spots developing inside the refrigerator
• Strange noises such as clicking or grinding emanating from the rear wall

Causes of a bad evaporator fan blade can be wear and tear over time, an accumulation of dust or debris on the blades restricting airflow, or accidental damage like dents or cracks to the blades affecting their ability to spin smoothly.

This OEM LG part is also compatible with select Sears/Kenmore brand models.

The Condenser Fan Blade is an OEM replacement part for LG refrigerators. The condenser fan motor blade is located on the condenser fan motor which is usually located on or near the compressor at the back of the refrigerator. This part is responsible for circulating air over the condenser coils. This helps to remove heat from the condenser and evaporate water in the defrost drain pan.

Causes of blade failure can include normal wear over extended runtime, accumulated dirt and dust impeding airflow, or physical impact damage.

Symptoms of a faulty condenser fan blade include:

• Refrigerator fails to properly cool and maintain temperatures
• Condenser unit runs excessively as heat fails to dispel
• Abnormal noises such as grinding or squealing emanate from the condenser area

This OEM LG part is also compatible with some Sears/Kenmore model refrigerators.

This fan grille assembly covers and protects the appliance fan while helping direct airflow and minimize noise. It's a direct-fit replacement component that restores proper ventilation and keeps debris away from the fan blades. What it does:

• Shields fan blades from objects and debris that can cause damage or binding
• Directs airflow for more consistent ventilation and cooling performance
• Helps reduce rattle or vibration caused by cracked or loose grille pieces
• Restores proper fan clearance when the original grille is warped or broken

• Disconnect power to the appliance before starting any work.
• Handle the grille carefully to avoid damaging mounting tabs; small plastic clips are common.
• Installation typically requires basic hand tools (screwdriver); align tabs and secure fasteners snugly.

This magnet-activated switch is a small sensor that tells the appliance when a door or lid is open or closed. Replacing a faulty switch restores proper lighting, door-ajar alerts, and safety interlocks for normal operation.

• Senses a nearby magnet to report door/lid open/closed status to the control
• Helps control interior lights, alarms, fans, and dispenser/ice interlocks on applicable units
• Failure symptoms can include lights staying on or off, false door-ajar beeps, or dispenser/ice disabled
• Common causes: moisture intrusion, damaged leads, or stuck internal contacts

• Disconnect power before servicing
• Access the switch at the door opening (behind trim/control housing or liner, location varies by model)
• Release locking tabs/fasteners, move wiring carefully, and install the new switch in the same orientation
• Restore power and verify operation by bringing a magnet near the switch to toggle

The Evaporator Fan Motor Assembly is an OEM replacement part for LG refrigerators. This assembly is responsible for circulating cold air from the evaporator coils throughout the refrigerator and freezer compartments. By doing so, it ensures that both compartments maintain the desired temperatures and that the cooling process is efficient.

Causes for a malfunctioning Evaporator Fan Motor Assembly can include motor wear from continuous operation, electrical issues like faulty wiring, obstructions preventing the fan blades from turning, or damage to the fan blades themselves.

Symptoms of a bad Evaporator Fan Motor Assembly include:

• Inconsistent temperatures in the refrigerator or freezer compartments
• Unusual noises, such as humming or buzzing, coming from the back of the refrigerator
• Reduced cooling efficiency, leading to food spoiling faster
• Frost buildup in the freezer due to poor air circulation

This OEM LG part is also compatible with Sears/Kenmore model refrigerators.

A replacement cover motor that powers the refrigerator's dispenser cover, allowing the door to open and close so you can access ice and water. Replaces a worn or failed motor to restore normal dispenser cover operation. What it does:

• Drives the dispenser cover mechanism so the cover opens when dispensing and closes when idle
• Helps keep the dispenser sealed to reduce drafts and prevent pests or debris from entering
• Stops or fails to move when worn, causing a stuck, slow, or noisy dispenser cover
• Works with the dispenser linkage and gears to coordinate cover motion with user controls

• One cover motor

• Disconnect power to the appliance before beginning any repair
• Remove dispenser trim and access panel per your model's service instructions to reach the motor
• Handle gears and linkage carefully; ensure proper alignment during reassembly and test cover operation before finishing

Damper motor support secures the damper motor assembly inside the refrigerator, keeping the air-control damper aligned so it opens and closes correctly. Replacing a damaged support restores proper airflow control and reduces noise. What it does:

• Secures and positions the damper motor assembly so the air-control damper moves smoothly.
• Keeps the motor and damper aligned to help prevent rattling, grinding, or loose motor noise.
• Supports consistent airflow between compartments to assist with even cooling.
• Resolve damper movement problems like the damper not opening or closing fully.

• Disconnect power to the appliance before starting work; remove food and shelves as needed for access.
• Remove the interior access panel to reach the damper assembly; handle plastic tabs and clips gently to avoid breakage.
• Align the motor and damper during reassembly and secure all fasteners; test damper operation before replacing panels and shelving.

This damper motor support replaces a broken or warped mount for the refrigerator's air damper assembly. It holds the damper motor and door securely so the system can meter freezer air into the fresh food compartment.

• Secures and aligns the air damper motor/door within the duct
• Helps ensure proper opening/closing of the damper to regulate airflow and temperature
• Damage can contribute to a warm or too-cold refrigerator and inconsistent temperatures
• May cause clicking or buzzing from the damper area or a visibly loose assembly

• Disconnect power to the refrigerator before servicing
• Access the damper behind the fresh food compartment duct/cover; remove shelves as needed
• Note wiring and orientation; transfer the existing damper motor and door to the new support and reuse fasteners
• Ensure the door moves freely and seals before reassembly; restore power and verify airflow

The PCB Assembly is an OEM part for LG refrigerators. It stands for Printed Circuit Board, which is the main control board that manages and regulates various functions and components within the refrigerator.

Symptoms of a bad PCB Assembly include:

• The refrigerator not powering on or displaying any lights/indicators
• Specific components or features not functioning correctly (ice maker, dispenser, cooling, etc.)
• Error codes or warning lights illuminated on the control panel
• Strange noises or abnormal behavior from the refrigerator

Causes of a bad PCB Assembly can be related to electrical faults, such as short circuits, power surges, or component failures. Physical damage from impact, moisture exposure, or overheating can also contribute to the malfunction of the PCB.

This OEM LG part is also compatible with Sears/Kenmore refrigerators. 

This sheathed heating element powers the automatic defrost system. It melts frost from the evaporator so air can circulate and temperatures stay consistent, helping restore cooling performance while preventing ice buildup.

• Provides controlled heat during the defrost cycle to clear ice from the evaporator coils
• Maintains airflow and stable temperatures for proper cooling
• Common failure symptoms: heavy frost on the back panel, warm or inconsistent temps, long run times
• Also presents as fan noise from ice contact or reduced cooling/ice production

• Disconnect power before service; allow any built-up ice to thaw
• Access the evaporator by removing interior panels; steps vary by model
• Handle the element carefully—do not kink, sharply bend, or stress the lead wires; transfer any clips/insulators from the original
• Check heater continuity and inspect the defrost thermostat/sensor while the area is open

Power cord assembly that restores the appliance's connection to household mains. Replaces a damaged or worn cord to help stop power loss, sparking, or intermittent operation and restore a safe power feed. What it does:

• Provides the main electrical connection from the wall outlet to the appliance so internal components receive line voltage.
• Replaces cords with visible damage, frayed insulation, exposed wires, or broken plug prongs.
• Can resolve symptoms such as no power, intermittent power, sparks at the plug, or breaker trips caused by a faulty cord.
• Restores the original style of power connection and strain-relief routing for a secure fit.

• Always disconnect power at the wall before attempting service.
• Basic hand tools may be required; secure the cord firmly with the appliance's strain relief and tighten screws.

This DC motor assembly powers a fan inside your appliance to move air where it's needed. Replacing a weak or failed motor restores proper airflow for stable temperatures and reliable performance. What it does:

• Drives a fan blade to circulate air within the appliance
• Supports consistent temperatures and efficient airflow
• Common failure signs: fan not running, intermittent operation, or grinding/squealing noises
• Contribute to poor cooling/heating and fan/motor-related error codes

• Includes: 1 DC motor assembly

• Disconnect power to the appliance before servicing
• Access the fan area, note wire routing/orientation, and remove mounting fasteners
• Transfer the fan blade and any mounting hardware from the original motor if needed
• Ensure the blade spins freely and connectors are fully seated before reassembly and power-up

The Main PCB Assembly is an OEM part for LG refrigerators. As the central control board, it directs functions like cooling performance, temperature regulation and dispenser operations. Located inside the back wall of the fridge compartment, the main PCB houses electronic components and circuitry that facilitate smooth appliance operation.

Causes can be water damage from condensation leaks, moisture penetration over time or normal wear of electronic systems.

Symptoms of a bad main PCB include:

• Inaccurate or unstable interior temperatures
• Improper functioning of cooling systems like fans or compressors
• Issues with ice/water dispensing processes
• Error codes displayed

This OEM LG part is also compatible with some Kenmore models.

This display cover assembly replaces a cracked, cloudy, or scratched control panel lens to restore the appliance's display visibility and protect the underlying electronics. It provides a clean, finished look for the console area. What it does:

• Protects the display and control electronics from spills, dust, and everyday wear
• Restores clear visibility when the original cover is scratched, discolored, or cracked
• Helps prevent moisture or debris from reaching the control board behind the panel
• Maintains the finished appearance of the appliance's console

• Disconnect power to the appliance before beginning any repair to avoid shock or damage
• Typically replaces the front lens of the control console; access may require removing trim or the control console
• Handle the cover carefully to avoid cracking; use appropriate trim clips or screws during reassembly
• Test the control board and connectors before assuming cover is the cause

The Ice Maker Assembly Kit is an OEM component specifically designed for LG refrigerators. This comprehensive kit includes the ice maker, auger motor, wire harness, and all mounting hardware necessary for installation.  

The ice maker assembly works by ejecting frozen cubes into the storage bin and rotating them into position using an internal auger. Over time, components can malfunction from regular wear.

Symptoms of a bad ice maker assembly include:

• Ice pieces jamming in the auger  
• Decrease in ice production amounts
• Motorized parts failing to operate properly
• Ice cubes not dispensing or ejecting 

This OEM LG ice maker kit addresses common ice maker failure caused by normal wear of moving parts. Upgrading to a new assembly restores full icemaking capability to LG refrigerators.

This OEM LG part is also compatible with Sears/Kenmore units. Proper maintenance of refrigerators prolongs the life of internal components.
 

The Auger Motor is an OEM part for LG refrigerators. It is responsible for dispensing ice from the icemaker into the ice bucket. 

Symptoms of a bad auger motor include:

• Slow or incomplete ice filling of the ice bucket
• Ice clumping or jamming in the auger assembly 
• Grinding or rubbing noises coming from the icemaker region
• The icemaker not producing any ice at all

Causes of a bad auger motor can be wear and tear over time, freezing or ice buildup preventing proper operation, or failure of internal motor components. 

This OEM LG part is also compatible with select Sears/Kenmore models. 

The Temperature Sensor is an OEM part for LG refrigerators. Also known as a thermistor, is responsible for sensing the temperature changes and providing the necessary feedback to the refrigerator's control board. It helps maintain accurate and consistent temperature levels, ensuring optimal food preservation and efficient cooling.

Causes of a faulty temperature sensor can include wear and tear over time, damage due to electrical issues or exposure to extreme temperatures, or sensor calibration issues. These factors can result in temperature inconsistencies, inaccurate readings, or improper cooling performance of the refrigerator.

Symptoms of a bad temperature sensor may include:

• Incorrect temperature readings on the control panel
• Temperature fluctuations inside the refrigerator
• Overcooling or inadequate cooling of food items

This OEM LG part can also be used on Kenmore/Sears appliances. 

This ice bucket assembly is the removable storage bin that collects and holds cubed ice from the refrigerator ice maker, restoring clean, contained ice storage and proper pickup by the dispenser or scoop. What it does:

• Collects and stores cubed ice produced by the ice maker so ice is contained and ready for use
• Guides ice toward the dispenser/auger area for consistent pickup
• Common symptoms it addresses: cracked or warped bin, ice spilling or falling out, ice not accumulating in the bin
• Fits into the freezer ice maker area and works with the factory guides and ejector mechanism

• Disconnect power to the refrigerator before servicing to avoid injury or damage
• Remove existing bucket by sliding it out of the guides; handle plastic parts gently to avoid cracking
• Reinstall by seating the bucket into the guides until it clicks or seats securely; ice maker components align before restoring power
• After installation, cycle power or run a test ice-making cycle to ensure proper operation

The Water Tank Assembly is an OEM part for LG refrigerators. It stores and supplies water for the refrigerator's dispenser and ice maker, ensuring a steady and clean water flow for these features.

Causes of a bad water tank assembly can include mineral buildup from hard water, leaks due to cracks or punctures, or contamination from mold or bacteria if the tank is not regularly cleaned. Over time, wear and tear from repeated use can also lead to failure.

Symptoms of a bad water tank assembly include:

• Water dispenser not functioning properly
• Reduced or no ice production
• Leaks or puddles inside the refrigerator
• Unpleasant taste or odor in the water

This OEM LG part is also compatible with Sears/Kenmore refrigerators.

An in-line union for appliance tubing, this tube connector joins two sections of plastic line to create a secure, leak-resistant connection in the water circuit, ideal for restoring flow after a repair, trim, or reroute. What it does:

• Connects two lengths of compatible plastic tubing to form a continuous run
• Helps maintain proper water delivery through the appliance's water system
• Can address leaks, drips, or loose/failed connections at a splice point
• Useful when replacing, shortening, or rerouting tubing during service

• 1 tube connector

• Disconnect power and shut off the water supply before servicing
• Cut tubing square; ensure ends are clean, round, and free of gouges
• Insert tubing fully into the connector until seated, then perform a gentle pull test
• Restore water and inspect all joints for leaks; use the connector size that matches your tubing's outer diameter

The Water Inlet Valve is an OEM part for LG refrigerators. It controls the flow of water into the refrigerator for the ice maker and water dispenser, ensuring a steady and controlled supply of water.

You should replace the water inlet valve if it becomes clogged, damaged, or fails to function properly. Causes of a bad water inlet valve can include mineral buildup from hard water, electrical malfunctions, or general wear and tear over time.

Symptoms of a bad water inlet valve include:

• The ice maker not producing ice
• The water dispenser not dispensing water
• Leaking water from the valve area
• Unusual noises when the valve is operating

This OEM LG part is also compatible with Sears/Kenmore refrigerators.

The Water Valve Assembly is an OEM part for LG refrigerators. It is essential for controlling the flow of water to the ice maker and the water dispenser. This solenoid-operated valve responds to signals from the refrigerator’s electronic control system to accurately manage the release of water, ensuring efficient operation and reliability.

Symptoms of a bad Water Valve Assembly include:

• The ice maker not producing ice or producing very small cubes
• The water dispenser not functioning or dispensing a trickle instead of a steady flow
• Water leaking from the refrigerator

Causes of a bad water valve assembly can stem from mineral deposits that clog the valve, electrical failures that impair the valve’s operation, or wear and tear from normal usage leading to leaks or malfunctions.

This OEM LG part is also compatible with Sears/Kenmore.

Note: Flow meter is not needed on all models, remove if necessary. Redesigned single valve replaces older dual solenoid valves. Wiring harness is included. Located behind the refrigerator.

This water filter assembly replaces the refrigerator's water filtration module to help restore clear-tasting water and steady flow. Fits models that use the AGF80300705 assembly and installs at the refrigerator water inlet. What it does:

• Filters sediment and common taste/odor contaminants to improve drinking water quality
• Restores reduced water flow caused by a clogged or failing filter module
• Helps reduce visible particulates and cloudiness in dispensed water
• Prevents unfiltered water from reaching the dispenser/ice maker when installed

• Turn off refrigerator water supply before replacing the assembly to avoid leaks
• Hand-tighten connections; avoid overtightening fittings to prevent damage
• Run and discard the manufacturer-recommended initial volume of water after install to flush the system

The Filter Head Assembly is an OEM replacement part for LG French door refrigerators. The component that houses the built-in water filter responsible for cleaning water delivered through the refrigerator’s internal dispenser and ice maker. With its precise fit, the filter head assembly ensures the water filter is securely held in place to do its job properly.

Symptoms of a bad filter head assembly include:  

• Water dispensing or ice making issues
• Water leaks around the filter area  
• Error messages related to filter replacement
• Inability to change or install a new filter

Causes of failure can be cracks, cracks, mineral buildup, or normal wear over time. Filter head assemblies in continuous use may need periodic replacement.

This OEM part is also compatible with some Kenmore side-by-side refrigerators.

This complete freezer door assembly replaces a damaged or worn freezer door to restore proper closure and cold retention. It fits the freezer compartment and includes the door shell and attached inner components for a like-for-like replacement. What it does:

• Replaces a cracked, dented, or warped freezer door to help prevent cold air loss
• Restores proper door alignment and sealing to reduce frost buildup and temperature issues
• Provides the original mounting points and inner components for easy fitment
• Helps the freezer maintain consistent performance when the old door can't close or seal properly

• Disconnect power to the appliance before starting any repair
• Remove food and shelves from the freezer area for access and safe handling
• Installation typically requires basic hand tools; support the door during removal/installation to avoid injury or damage
• If the door contains glass or trim, handle carefully.