Parts for Frigidaire FPCE22VWFA3: 09 - Ice Maker And Installation Parts

This tube clamp secures small tubing and lines inside the appliance to prevent movement and reduce wear. It keeps hoses and tubes routed properly so they don't rub against sharp edges or vibrate during operation. What it does:

• Holds water, drain or refrigerant tubing in place to prevent sagging and chafing
• Reduces vibration and rattling from loose lines
• Helps prevent tubing wear that can lead to leaks or pinch damage
• Keeps hoses routed neatly for reliable appliance operation

• Disconnect power and shut off water supply before beginning any repair
• Remove any access panels needed to reach the clamp location; use caution around sharp sheet metal
• Replace only the damaged clamp with the same style and secure tubing firmly but without over-tightening
• If tubing shows damage where it was rubbing, replace or repair the tubing before reinstalling the clamp

This replacement insulator cushions and secures appliance components to reduce vibration and noise for smoother operation. A simple, durable part that restores proper spacing and helps prevent rubbing or wear from vibration. What it does

• Cushions components to reduce vibration, rattling and noise during operation
• Helps maintain correct spacing and alignment of mounted parts
• Protects parts from wear by preventing metal-to-metal contact
• Commonly replaced when vibration or unusual noise is present

• One insulator

• Disconnect power (unplug or shut off breaker) before starting any repair
• Remove access panels or panels required to reach the original insulator
• Press or seat the insulator into the original mounting location; may require light hand force or basic tools
• Inspect surrounding mounting hardware and replace any worn clips or fasteners for a secure fit

This part has been discontinued by the manufacturer and is no longer available.

This velcro pad secures trim or components to the appliance housing, reducing rattles and helping panels stay aligned for a cleaner fit. It provides a low-profile attachment point that uses hook-and-loop fastening for easy repositioning. What it does:

• Attaches to housing surfaces to hold trim, panels, or small components in place
• Prevents vibration noise and keeps parts from shifting during operation
• Provides a reusable hook-and-loop fastening point for service or adjustments
• Helps maintain a flush, finished appearance of the appliance exterior

• Clean and dry mounting surface before applying to ensure adhesion
• Remove backing and press pad firmly into place; allow adhesive to set per manufacturer guidance
• Replace any damaged mating loop material for best hold
• Use basic hand tools only; disconnect power if working near electrical components

This water inlet valve controls water flow to the refrigerator's dispenser and ice maker, restoring proper filling and dispensing when functioning. Designed for direct replacement to stop leaks or restore water delivery. What it does

• Opens and closes water supply lines to the dispenser and ice maker using two solenoids
• Replaces a failed valve that causes no water or reduced water to the dispenser or ice maker
• Stops intermittent leaks or continuous flow caused by a stuck or damaged valve
• Works with the refrigerator's water pressure and electronic controls to meter fills

• One water inlet valve assembly

• Turn off water supply and unplug the appliance before servicing
• Inspect inlet screen/filters and supply line for debris when replacing valve

1/4"diameter - 93" long, plastic, cut-to fit

1/4"diameter - 93" long, plastic, cut-to fit

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued and is no longer available.

This spring-style hose clamp secures flexible appliance hoses and helps prevent leaks by holding hose ends tightly to fittings. Reliable, low-profile design for use on drain, water, or vent hoses where a strong, consistent grip is needed. What it does:

• Provides a spring-tensioned grip to keep hoses seated on fittings and reduce leaks
• Commonly used on flexible drain or water hoses and small vent lines
• Helps maintain proper connection under normal vibration and thermal cycling
• Replaces worn, stretched, or corroded clamps that no longer hold tension

• One spring hose clamp (exact quantity as sold)

• Use pliers to expand the clamp, slide into position, then release to seat on the fitting
• Inspect hose ends and fittings for wear; replace hose if damaged before installing clamp
• Wear eye protection when compressing the clamp; keep fingers clear of the clamp's edges
• Tighten only as needed—over-compressing can damage the hose