Parts for Electrolux EI23BC56IB6: 17 - Ice Maker Parts

The Air Filter is an OEM part for Frigidaire refrigerators designed to enhance the air quality inside the refrigerator, ensuring that food stays fresh and odor-free.

The Air Filter helps to remove unwanted odors and impurities from the refrigerator's circulating air. It absorbs and neutralizes common food odors, keeping your fridge smelling clean and pleasant. The activated carbon filter is 7 times more effective than baking soda at removing odors. 

For best results, change filter every 6 months. 
Color: Black. 
Measures about 7 inches wide by 5 inches deep. 

Symptoms of a bad air filter include:

• Lingering food odors inside the refrigerator
• Increased presence of stale or unpleasant smells
• Decreased effectiveness in eliminating odors

Replace your Air Filter with this genuine part to ensure a clean and fresh-smelling refrigerator. This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Refrigerator ice maker mounting frame that secures the ice maker assembly to the freezer compartment wall. Replace if cracked, broken, or missing.

Mounting bracket for bottom-mount refrigerators. Secures internal components. Replace if cracked, broken, or missing to restore proper fitment.

Mounting bracket for bottom-mount refrigerators. Secures internal components in place. Replace if cracked, bent, or broken to restore proper support.

Replacement shaft for bottom-mount refrigerators. Installs in mechanical assembly. Needed when original shaft is bent, broken, or worn down.

This is a bimetal thermostat mounted on the ice maker mold that senses temperature to control the ice harvest cycle. It signals the ice maker to begin the harvest and eject ice once the mold reaches the proper temperature. Replace this thermostat if the ice maker stops producing ice, runs continuously without ejecting cubes, or if ice cubes are only partially frozen.

Secures refrigerator hoses and tubing to prevent leaks. Replace if loose, cracked, or during water line repairs. Verify fit with your model number.

Wiring harness for bottom-mount refrigerators. Connects electrical components inside the appliance. Replace if wires are frayed, damaged, or broken.

This is a cartridge-style heater embedded in the ice maker mold that warms the mold just enough to release ice cubes during the harvest cycle. It allows the ice to separate cleanly from the mold so it can drop into the ice bin. Replace this heater if the ice maker stops ejecting ice, cubes are incomplete or stuck in the mold, or the ice maker has stopped cycling.

Replaces a cracked or damaged ice maker tray assembly in your refrigerator. This tray molds and releases ice cubes within the ice maker housing.

This is a small electric motor that drives the ice maker's ejector mechanism, rotating the sweep arm to push ice cubes out of the mold and into the storage bin. It is mounted inside the ice maker module in the freezer compartment. Replace this motor if your ice maker stops cycling, fails to eject ice, or you hear the motor humming without the ejector arm moving.

Ice maker won't stop making ice or overflows? This shut-off arm controls ice production by signaling when the bin is full. Simple DIY fix for most models.

Secures trim panels and small components inside your refrigerator. Replace this mounting screw if stripped, missing, or worn to restore proper fit.

Mounting screw for bottom-mount refrigerators. Secures interior components, shelves, or panels. Replace if stripped, missing, or damaged during repair.

This thermistor kit is the refrigerator temperature sensor assembly that monitors internal air temperature so the control can run the compressor and fans at the right times. Replaces a failed sensor to restore proper temperature sensing and cycling. What it does:

• Detects refrigerator/freezer compartment temperature and sends that signal to the control board
• Helps the control manage compressor and fan runtime for consistent cooling
• Commonly used when the fridge is not maintaining temperature or cycles erratically
• Works as the sensor portion of the evaporator/air-sensing circuit in compatible models

• Disconnect power before servicing to avoid shock or damage.
• Handle the sensor and connector gently; do not kink the sensor lead or damage the probe tip.
• Route the harness and secure clips per the original layout to ensure accurate sensing.

Refrigerator not cooling or freezing over? This evaporator coil absorbs heat to cool your fridge. Common fix for warm compartments and frost buildup.

Fixes ice buildup in freezer or frost on back wall. This defrost heater melts accumulated frost during defrost cycles. Moderate DIY difficulty.

Secures panels, brackets, and trim on appliances. Replace when missing, stripped, or damaged to restore a tight, rattle-free fit and proper alignment.

Replacement screw for refrigerator assembly. Used to secure panels, shelves, or internal components. Needed when original is stripped, lost, or damaged.

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head

Ice maker stopped working or water dispenser not flowing? This refrigerator water valve controls water to both. Easy 10-20 minute DIY fix with video.

Secures internal refrigerator components and assemblies. Replace if bracket is cracked, broken, or missing to restore stable mounting and alignment.

Secures tubes and wiring in your refrigerator. Replace if clips are broken or connections are loose. Confirm fit with your model number.

Electrical harness wire for refrigerators. Replaces damaged, frayed, or disconnected internal wiring. Essential when harness is broken or melted.

Water inlet tube for refrigerators. Connects the water supply to the dispenser or ice maker. Replace if cracked, kinked, leaking, or damaged.

Fill tube assembly that connects water supply to the ice maker in your refrigerator. Replace if tube is cracked, leaking, or grommet is worn or missing.

Fix frost buildup in your refrigerator's freezer with this defrost heater. Solves icing problems and restores proper cooling. Moderate DIY repair.

Secures tubes and wiring in your refrigerator. Replace if clips are broken or connections are loose. Confirm fit with your model number.

Electrical harness wire for refrigerators. Replaces damaged, frayed, or disconnected internal wiring. Essential when harness is broken or melted.

Fix frost buildup in your refrigerator's freezer with this defrost heater. Solves icing problems and restores proper cooling. Moderate DIY repair.

Fill tube assembly that connects water supply to the ice maker in your refrigerator. Replace if tube is cracked, leaking, or grommet is worn or missing.

Water inlet tube for refrigerators. Connects the water supply to the dispenser or ice maker. Replace if cracked, kinked, leaking, or damaged.

Replacement mounting screw for refrigerator panels, brackets, and trim. Secures loose or missing fasteners to stop rattles and keep components aligned.

Replacement mounting screw for refrigerator panels, brackets, and trim. Secures loose or missing fasteners to stop rattles and keep components aligned.

Hex head screw that secures panels, brackets, and internal components in refrigerators and appliances. Replace when missing, stripped, or damaged.

Replacement ice dispenser chute for bottom-mount refrigerators. Guides ice from dispenser to door opening. Replace if cracked, broken, or warped.

Hex head screw that secures panels, brackets, and internal components in refrigerators and appliances. Replace when missing, stripped, or damaged.

Replacement ice dispenser chute for bottom-mount refrigerators. Guides ice from dispenser to door opening. Replace if cracked, broken, or warped.

Connects sections of water tubing inside your refrigerator. Replace this adapter if cracked, leaking, or popping off to stop drips and water damage.

Connects sections of water tubing inside your refrigerator. Replace this adapter if cracked, leaking, or popping off to stop drips and water damage.