Parts for Electrolux EILFU17GS0: 09 - Ice Maker Parts

Water inlet tube routes water from the supply line to your freezer's dispenser and ice maker. Replace if cracked, damaged, or leaking at connections.

This name plate is the replacement identification label that mounts to the appliance exterior to display model, rating and manufacturing information — making it easier to identify and service the unit. What it does:

• Provides the factory identification label with model and rating details for accurate appliance identification
• Restores legibility when the original plate is scratched, faded or missing
• Helps technicians confirm correct replacement parts and service information
• Supports resale value and safety by ensuring required labeling is visible

• One replacement name plate

• Always disconnect power and shut off gas or water supply before servicing
• Clean and dry the mounting surface before installing to ensure proper adhesion or fit
• This part replaces the visible identification plate only; the part number on the plate matches your unit before installation
• If mounting hardware or adhesive is required, use the method specified by your model's service instructions

Ice maker clicking or not producing ice? A worn drive gear with stripped teeth is often the cause. This 5-minute fix restores normal ice production.

Mounting plate secures internal components in your freezer. Replace if cracked, warped, or missing to restore proper support and stability.

Ice maker stopped making ice? This complete ice maker assembly resolves no ice production and leaking issues. Easy DIY install with video guide included.

Wiring harness for refrigerators. Connects electrical components inside the appliance. Replace if wires are damaged, frayed, or connections are loose.

Fixes freezer not cooling properly or running too cold. This defrost thermostat restores proper temperature control. Direct replacement, moderate DIY.

Water dispenser won't shut off or ice maker won't fill? This door switch detects when the door closes to control dispensing and cycles. Easy DIY fix.

Support plate for freezer interior mounting. Replaces cracked, broken, or missing support plates that compromise shelf or component stability.

Ice maker stopped making ice? This complete ice maker assembly resolves no ice production and leaking issues. Easy DIY install with video guide included.

Ice maker stopped making ice? This complete ice maker assembly resolves no ice production and leaking issues. Easy DIY install with video guide included.

Replacement mounting screw for freezers and refrigerators. Secures interior components and panels. Order now if your original screw is missing or stripped.

Note: The ice stripper is no longer available. Order complete icemaker by model number.

Ice maker not shutting off or making too much ice? A worn lever arm prevents proper shutoff. Simple replacement takes under an hour to restore function.

Mounting screw for freezer and refrigerator assembly. Secures panels, shelves, or internal components. Replace if stripped, missing, or damaged.

This replacement screw secures appliance components so panels, trim, or brackets stay fastened and aligned. Use it to replace lost or stripped fasteners and stop rattling, loose panels, or parts that won't sit flush. What it does

• Fastens panels, trim pieces, brackets, and small components to the appliance frame
• Replaces worn, stripped, or missing screws that cause rattling or gaps
• Restores secure mounting and alignment for doors, controls, or interior parts
• Works wherever the OEM screw 5304456677 is specified

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not over-torque to prevent thread or part damage
• Compare new screw to the original to ensure correct fit before installation
• Disconnect power to the appliance if working near electrical components

Timing adjustment screw for refrigerator ice makers. Controls water fill duration. Replace if stripped, missing, or damaged during ice maker maintenance.

Mounting plate that secures the valve switch inside your freezer. Replace if the original plate is cracked, broken, or missing to properly support components.

Replacement screw for securing refrigerator panels, brackets, and trim. Restores proper fit and reduces rattling from loose or missing fasteners.

Replaces your refrigerator's ice maker cover if cracked, broken, or missing. This protective cap installs on the ice maker assembly in your freezer.

Replaces a cracked, brittle, or damaged fluid transfer tube in your upright freezer. Restores secure connections and prevents leaks in the system.

Ice maker not filling or leaking water? The water inlet valve controls flow to your ice maker and dispenser. Moderate DIY repair with video guide.

Replacement mounting screw for refrigerators and ice makers. Secures panels, brackets, and internal components. Needed when original is missing, stripped, or damaged.

Missing or cracked ice bin? This ice bucket stores ice from your refrigerator's ice maker. Simple pull-out replacement installs in seconds.

This replacement label provides the appliance's identification and rating information so you can restore clear model, serial, and safety marking visibility. It helps owners specifications and service details at a glance. What it does:

• Displays model, serial, and electrical rating information for the appliance
• Restores worn or missing safety and regulatory markings
• Keeps identification visible for warranty and service calls

• One replacement identification/rating label

• Clean and dry the mounting surface before applying; remove any dirt, grease, or old adhesive
• Align carefully and press firmly to ensure full adhesion; allow adhesive to set per room temperature conditions
• Do not place over vents, moving parts, or control openings
• For safety, disconnect power to the appliance before accessing internal areas to reach the original label location

Freezer stopped making ice? This ice maker assembly restores automatic ice production. Connects to existing water supply and wiring for reliable operation.

Seals internal refrigerator components to prevent air leaks and moisture intrusion. Replace when worn to maintain proper airflow and temperature control.

Connects sections of water tubing inside your refrigerator. Replace this adapter if cracked, leaking, or popping off to stop drips and water damage.