Ikea Range Parts

This oven door hinge restores smooth, controlled door movement and a tight seal. Replace a worn hinge to help your oven close properly, retain heat, and operate safely without slamming, sagging, or uneven gaps.

• Supports and pivots the oven door; spring tension controls opening and closing
• Helps the door sit flush against the gasket to minimize heat loss
• Restores alignment when the door feels loose, sags, or doesn't close evenly
• Resolves symptoms like door slamming, uneven gaps, poor temperature regulation, or extended preheat times

• Disconnect power at the breaker; shut off gas supply if applicable
• Support the door; engage hinge locks and remove the door
• Replace the hinge and securely reinstall using existing fasteners
• Rehang the door, verify latch engagement and seal, and test door movement

The Range Glass Assembly is an OEM part for Frigidaire ranges. It covers the inner cooking cavity, protecting both the occupant and the heating elements and mechanisms inside. The glass assembly also allows for viewing into the oven to check on food without needing to open the door each time. 

Symptoms of a bad glass assembly include:

• Cracks or breaks in the glass
• Difficulty viewing into the oven cavity 
• Leaks around the glass seal
• The glass popping out of place

Causes of a bad glass assembly can be wear and tear over time, exposure to excessive heat, or damage from impacts. 

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement filter restores clear airflow through your appliance's venting system. It captures airborne particles so the fan can exhaust efficiently and helps protect internal components from buildup.

• Traps grease and other particulates in the air stream
• A clogged or damaged filter can reduce airflow and strain the blower
• Replace when torn, warped, or heavily saturated
• Common symptoms: weak venting performance, lingering steam/odors, visible residue on or around the filter

• Disconnect power to the appliance before servicing
• Access the filter from the intake grille or bottom panel and release the retaining tabs/screws
• Install the new filter in the same orientation; ensure it seats fully and locks in place
• Restore power and test fan operation on each speed

For Use With LP

This orifice spud meters gas to a burner on your range or cooktop, setting proper flame size for efficient, even heating. Replacing a damaged or incorrect spud restores consistent burner performance and flame quality.

• Meters gas flow through the burner orifice to control flame height and shape
• Supports efficient combustion and consistent heat output
• Common fix for flames that are too high/low, yellow/sooty, or uneven
• Used when setting up or converting a model for the specified fuel type (LP or natural), per the position of each burner

• Shut off the gas supply and disconnect electrical power before servicing
• Remove the burner cap and head to access the spud; lift the cooktop or open the range top if required
• Remove/install with a properly sized wrench; do not overtighten. Apply thread sealant only if specified by the manufacturer
• Match each spud to the correct burner and fuel type per your model documentation; after reassembly, restore gas and leak-test with a soapy-water solution

This surface burner infinite switch is the behind-the-knob control for an electric cooktop or range. It regulates power to a single surface element so you can dial in and maintain the heat you need.

• Regulates on/off power cycling to a coil or radiant surface element for variable heat control
• Helps address issues such as a burner not heating, only heating on high, not turning off, or fluctuating temperature
• Installs behind the control panel; connects with spade terminals to line, load, and element leads
• Single-surface-element control for one burner position

• Disconnect power before servicing; this component carries high voltage
• Note wire positions or transfer one wire at a time from the old switch to the new switch
• Secure the switch to the control panel and align the shaft with the control knob
• Reassemble and verify smooth low-to-high burner operation

The Regulator is an OEM part for Frigidaire cooktops. It is responsible for regulating the flow and pressure of gas entering the appliance, ensuring safe and efficient operation.

A bad regulator can be caused by faulty internal components, wear and tear over time, or damage due to improper handling. Signs of a faulty regulator include uneven heating, weak flame, or gas leaks.

Symptoms of a bad regulator can include:

• Uneven heating of burners or oven 
• Weak or inconsistent flame 
• Gas leaks around the regulator 

This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Glass is an OEM part for Frigidaire freestanding ranges. It provides a durable transparent barrier that allows for viewing of contents inside the oven. The tempered glass door is both impact-resistant and heat-resistant, built to withstand repetitive use.

Causes of bad oven door glass include cracks or chips developing from accidental impacts, warping or discoloration from overheating, or scratches that won't wipe clean. 

Symptoms of a bad glass oven door include:

• Inability to safely or securely close the oven door  
• Reduced visibility into the oven cavity
• Potential safety hazards from cracked or compromised glass

This OEM Frigidaire replacement restores the door's integrity and functionality. It is also compatible with Electrolux, Kelvinator, and some Kenmore electric range models. 

LP Conversion Kit lets you convert a natural-gas cooktop or range to run on propane (LP), helping burners operate safely at the correct orifice size and pressure. Use the kit when changing fuel type or when burner flames perform poorly. What it does:

• Converts burner fuel delivery so the appliance can operate on propane (LP).
• Restores expected flame shape and heat output after switching fuel types.
• Helps address ignition issues, sputtering, weak flames, or yellow/tall flames caused by incorrect orifice sizing.
• Ensures the appliance meets manufacturer fuel-type requirements when properly converted.

• Follow the manufacturer's LP conversion instructions exactly; improper conversion can be hazardous.
• Shut off gas supply and disconnect power before starting; test all connections for leaks after installation.
• Keep the kit parts and conversion instructions for future service or warranty reference.

This surface burner spark electrode creates the spark that lights the gas on your cooktop or range. Replacing a worn or cracked electrode helps restore quick, reliable ignition and can reduce excessive clicking at the affected burner. What it does:

• Generates a high-voltage spark at the burner head to ignite gas
• Helps ensure fast, consistent ignition for the specific burner
• Common symptoms can include no spark/no light at one burner, weak or intermittent sparking, or continuous clicking from a damaged/contaminated insulator
• For the surface burner ignition circuit

• 1 spark electrode

• Disconnect power and shut off gas before servicing; allow the cooktop to cool completely
• Remove burner cap and head to access the electrode; note wire routing and connection
• Transfer/reuse any mounting hardware; avoid stressing or cracking the ceramic insulator
• Align the tip to the burner per service information and ensure all connections are secure before restoring power and gas

This replacement grill grate restores a sturdy, level grilling surface on your cooktop or range. Replace a cracked, warped, or missing grate to maintain safe support and consistent heat over the grill area.

• Provides the elevated grilling surface above the heat source for stable, even cooking
• Keeps food positioned at the proper height for consistent searing and results
• Replace if cracked, broken, warped, or heavily corroded
• Helps resolve rocking/unstable surface or uneven cooking caused by a damaged grate

• Turn appliance off and allow all surfaces to cool completely before handling
• Lift off the old grate and clean debris from the support ledges or frame
• Set the new grate in the correct orientation; ensure it sits flat and stable
• Verify proper clearance around adjacent components before use

The Motor-Fan is an OEM component specifically designed for Whirlpool kitchen ranges. Located within the back wall of the oven cavity, the motor fan works to circulate air and remove excess moisture and smoke during the cooking process. Proper motor-fan functioning helps ensure efficient oven ventilation and performance.

Symptoms of a bad motor fan include:

• Excessive smoke or moisture left in the oven after cooking  
• Oven taking longer to preheat and cook due to poor air circulation
• Loud buzzing or grinding noises emanating from the fan

Causes of failure are normally wear and tear of motor windings or fan blade bearings from years of continuous use. Overheating can potentially reduce lifespan as well. 

This OEM Whirlpool part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This support bracket secures an appliance cabinet component or mounting point to restore alignment and reduce movement. It replaces worn or broken supports so panels and internal parts stay properly positioned during normal operation. What it does

• Holds a cabinet panel, frame, or internal component in place to maintain proper alignment.
• Stabilizes mounting points to help reduce vibration, rubbing, or intermittent noise.
• Common replacement when you notice a loose or sagging panel, rattling, or unusual chassis movement.
• Provides a direct mechanical fix—matches the OEM bracket design and fit.

• Disconnect power (and shut off gas supply for gas appliances) before starting any repair.
• Remove necessary panels and fasteners to access the old bracket; keep track of all screws and clips.
• Compare the new bracket to the old part for orientation before installing; secure using the original fasteners—do not overtighten.

This rear latch assembly secures the dryer door so the appliance can latch and run properly. It replaces a worn or broken rear latch to restore reliable door closure and help the dryer start and stay closed during cycles. What it does:

• Secures the dryer door to engage the door switch so the dryer will start
• Keeps the door closed during operation to prevent interruptions mid-cycle
• Replaces a broken, bent, or worn latch that prevents the door from latching
• Commonly used when the dryer won't start, stops unexpectedly, or the door won't stay closed

• Disconnect power (unplug or switch off breaker) before beginning any work
• Installation may require removing the dryer top or front panel; follow the model's service instructions
• Handle panels and metal edges carefully to avoid cuts
• After installation, verify the door latches securely and the dryer starts before reassembling all panels

Color: Black

The Knob is an OEM part for Frigidaire ranges. The knob attaches directly to the surface element switch and allows for easy adjustment of settings with a simple turn.

Causes of a bad range knob can be normal wear and tear over time, exposing the knob to excessive heat, or accidental damage from impact.

Symptoms of a bad range knob include:

• Loose, wobbly or difficult to turn fitment
• Cracked, broken or missing pieces
• Control functions that do not work as intended
• Inaccurate temperature readings
• Knob that falls off or does not stay securely attached

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.