Ikea Wall Oven Parts

This is the glass panel used in the oven door window. Replace it to restore a clear view into the oven and maintain the door's proper heat barrier if the original pane is cracked, shattered, or damaged.

• Forms the viewing window and thermal barrier in the oven door
• Helps the oven retain heat for consistent cooking
• Direct replacement for a cracked, shattered, or missing pane
• Typical symptoms: visible cracks, shattered glass, rattling fragments, or reduced visibility

• Disconnect power or gas and allow the oven to cool completely before service
• Wear cut-resistant gloves and eye protection; handle broken glass with care
• Support the door; remove the door and any trim as outlined in your model's service information
• Transfer any reusable brackets/trim from the original glass and avoid overtightening fasteners

This spark module supplies the high-voltage pulses that ignite the surface burners on a gas cooktop or range. Replacing a failing module helps restore consistent clicking and spark so burners light promptly and reliably.

• Supplies high-voltage to up to five surface igniters (5+0 configuration)
• Sends spark when a burner control is turned to Lite
• Failure symptoms can include no spark on all or multiple burners
• May also cause intermittent/weak spark or continuous clicking

• Disconnect power and shut off gas before servicing
• Note wire locations; move one connector at a time to matching terminals
• Mount securely in the original position and ensure proper grounding
• After replacement, if only one burner won't ignite, inspect that burner's switch and igniter

This oven door hinge restores smooth, controlled movement so the door opens easily and closes fully for a reliable seal. Replacing a worn hinge helps reduce heat loss and supports consistent cooking performance and safe operation.

• Provides the pivot and spring-assisted action for opening and closing the oven door
• Helps pull the door closed and hold it at intended stop positions
• Maintains even gasket contact to keep heat inside the cavity
• Common symptoms of a failing hinge: door won't close fully or sit flush, drops or slams open, binds or pops when moving, or shows an uneven gap

• Disconnect power and allow the oven to cool completely before servicing
• Support the door; open to the removal position and release hinge locks, then lift the door off
• Use caution—hinge springs are under tension; wear hand and eye protection
• Install in the same orientation and verify door alignment and smooth operation after reassembly

This oven door hinge restores smooth, controlled door movement and a proper seal. Worn hinges can cause a sagging door, poor closure, or binding—replacing the hinge helps maintain safe operation and consistent cooking performance.

• Supports the oven door with a spring mechanism for controlled opening and closing
• Helps pull the door tight against the gasket for an effective seal when closed
• Works with the opposite hinge to keep the door aligned and stable
• Common symptoms include door not closing fully, sagging or dropping, hard-to-open/close action, or heat escaping around the door

• Disconnect power and allow the oven to cool completely before servicing
• Remove the door following your model's instructions; engage hinge locks or use retaining pins if provided
• Replace the hinge in the same orientation; ensure hinge arms are fully seated in the receivers
• Reinstall the door and verify smooth motion and a complete seal

This is a smoothtop assembly intended for use with ranges by major manufacturers. This component is located on top of the stove and protects the wiring and heating elements on the interior. The smoothtop assembly is made of strong glass. This part can become damaged and may be unsafe for use. If this happens, the smoothtop assembly will need to be replaced.A set of basic tools will be needed to replace this part. Work gloves can also be useful for preventing injuries from broken glass. First, turn off the range. Unplug it from the wall and make sure it is cool to the touch. Open the oven to remove the screws that hold the smoothtop assembly in place. Pick it up and disconnect the heating elements and wires. Next, install the new smoothtop assembly and hook back up the internal components. Plug in the appliance before use.This is an authentic OEM replacement component that is sourced directly from the manufacturer. It is sold on an individual basis. The smoothtop assembly is made to be used with ranges, ovens, and stoves created by Ikea, Frigidaire, and Crosley.

The Surface Burner Orifice Holder is an OEM part specially designed for Whirlpool gas ranges and cooktops. This part holds and positions the burner orifice above the surface burner, facilitating the mixture of gas and air required for combustion. 

Symptoms of a bad orifice holder include:

• Yellow or incomplete burner flames  
• Flames not remaining centered on the burner surface
• Burners that will not light or stay lit
• Gas leaks detected around the burner area

This is also compatible with Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, and Roper gas ranges and cooktops. 

This orifice controls the flow of gas to a burner, helping produce the correct flame for safe, consistent cooking and baking. It replaces a worn or damaged gas metering jet to restore proper burner performance. What it does:

• Meter gas flow to a specific burner for correct flame size and heat output
• Helps maintain steady ignition and even cooking when functioning properly
• Commonly used when a burner shows a weak, uneven, or no flame
• Also replaces corroded or clogged jets that restrict gas flow

• Turn off the gas supply and power to the appliance before beginning work
• Use appropriate tools and avoid overtightening; match the replacement to the original part number
• Inspect for debris or corrosion and clean mating surfaces before installation

A surface ignitor that produces the spark needed to light gas burners on compatible ranges and cooktops. Replaces a worn or failed ignitor to restore reliable ignition and consistent burner lighting. What it does

• Creates the spark at the burner to ignite gas when the control is turned on.
• Commonly used when burners click but fail to light or when a specific burner never ignites.
• Works with the cooktop's ignition system to provide consistent, repeatable sparking.
• Fits into the burner assembly and connects to the appliance's existing wiring and mounting.

• One surface ignitor (quantity: 1)

• Disconnect power to the appliance and shut off the gas supply before starting any service.
• Handle the ignitor by the ceramic/insulated areas; avoid touching the tip with bare hands to prevent contamination or damage.
• Confirm correct fit and secure all wiring connections; test ignition on a safe flame setting after reinstalling.

The Rear Oven Door Glass is an OEM part for Whirlpool ovens. This glass panel is installed on the inside of the oven door and is essential for providing a heat-resistant viewing window, allowing users to monitor the cooking process without opening the door. Measuring about 20 inches by 10 inches, this quality glass keeps heat in the oven and provides a clear view for easy baking.

Symptoms of a bad Rear Oven Door Glass include:

• Cracks or chips in the glass,
• Visible streaks or fogging between glass layers that can't be cleaned,
• A loose fit that may cause heat to escape or the glass to rattle during oven use.

Causes of rear oven door glass damage typically include thermal stress from high heat, impact from closing the door too forcefully, or accidental bumps with pots or pans.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This inner door glass is the heat-resistant panel mounted on the inside of the oven door. It restores a clear, secure barrier to help retain heat and visibility when the original glass is cracked, shattered, or stained.

• Forms the inner pane of the oven door to contain heat and allow viewing of food
• Damage can cause heat loss, longer preheat/cook times, and unsafe sharp edges
• Cracked, shattered, or missing glass should be replaced before using the appliance
• Cloudy or permanently stained glass reduces visibility into the oven

• Disconnect power at the breaker and allow the oven to cool completely
• Wear cut-resistant gloves and eye protection; handle glass carefully
• Support or remove the door and work face-down on a padded surface
• Transfer any brackets/clips/insulation as configured; do not overtighten fasteners against the glass

This is a glass door outer panel assembly that has been manufactured by Whirlpool for use with ovens. The glass door outer panel assembly contains everything needed to replace a broken or deteriorated door. The door needs to be in proper working order to keep heat-sealed inside the oven, as well as allow the user to easily access the oven. Over time, this part could become dented, bent, scratched, cracked, or otherwise rendered ineffective, requiring replacement. This part may require two people to install as it is heavy. Unplug the oven and allow it to cool down entirely before attempting any repairs.As a genuine OEM part, this part has been sourced directly from the manufacturer and is only sold individually. This glass door outer panel assembly is manufactured from high quality and durable materials to ensure sturdiness. It is intended for use with ovens and ranges manufactured by Whirlpool, Maytag, Kitchenaid, Amana, and Magic Chef.

LP Conversion Kit lets you convert a natural-gas cooktop or range to run on propane (LP), helping burners operate safely at the correct orifice size and pressure. Use the kit when changing fuel type or when burner flames perform poorly. What it does:

• Converts burner fuel delivery so the appliance can operate on propane (LP).
• Restores expected flame shape and heat output after switching fuel types.
• Helps address ignition issues, sputtering, weak flames, or yellow/tall flames caused by incorrect orifice sizing.
• Ensures the appliance meets manufacturer fuel-type requirements when properly converted.

• Follow the manufacturer's LP conversion instructions exactly; improper conversion can be hazardous.
• Shut off gas supply and disconnect power before starting; test all connections for leaks after installation.
• Keep the kit parts and conversion instructions for future service or warranty reference.

Replace a worn or missing control knob and restore precise, dependable setting selection on your appliance. This knob press-fits onto the control shaft to provide a secure grip and smooth, consistent operation.

• Attaches to the control shaft on the front panel
• Lets you turn the control to select heat, temperature, or function settings
• Common symptoms: cracked hub or stripped insert; knob wobbles, slips, falls off, or won't turn the control

• Disconnect power before servicing; shut off gas supply
• Pull the old knob straight off; align the flat/D-shape on the new knob with the shaft and press fully into place
• Do not use excessive force or tools; avoid bending the control/valve stem