Ikea Wall Oven Parts

NAT to LP gas conversion kit

This is a replacement black burner grate for gas ranges. It provides a stable cooking surface so pots and pans sit securely over the burner, restoring safe, even cookware support. What it does:

• Supports pots and pans above the burner for stable cooking
• Restores proper pot-to-flame positioning for consistent heating
• Replaces warped, cracked, chipped or missing grates that cause cookware wobble
• Protects the cooktop surface from direct contact with hot cookware

• Designed for drop-in replacement; no special tools usually required
• Allow the cooktop and grate to cool completely before handling
• Inspect burners and ports for debris before reinstalling the grate
• If you smell gas or detect a problem with burner operation, stop use and have the appliance serviced.

This leveling foot threads into the appliance base to support and precisely level the cabinet on uneven floors. Replacing a worn or missing foot restores stability, reduces rocking and vibration, and helps doors and components operate correctly.

• Provides height adjustment to level the appliance on uneven floors
• Stabilizes the cabinet to minimize rocking, rattling, and excess vibration
• Helps maintain proper door alignment and seal contact when leveled
• Common signs of wear: broken/missing pad, stripped or seized threads, unit wobbles or won't sit level

• Disconnect power; shut off water supply if applicable
• Protect flooring and use a helper to carefully tilt or raise the appliance for access
• Unthread the old foot; hand-thread the new foot into the base insert, avoiding cross-threading
• Use a level to adjust feet until stable; verify clearances and operation

This genuine replacement wire harness connects and routes power and signal lines between appliance components, restoring reliable electrical communication for normal operation and control response. What it does:

• Replaces damaged or frayed wiring that can interrupt power or signals
• Restores reliable connections between controls, motors, and sensors
• Helps resolve intermittent operation, loss of certain functions, or failure to start when caused by wiring faults
• Provides factory-style connectors and routing for secure, vibration-resistant connections

• Disconnect power to the appliance before starting any repairs
• Handle connectors carefully; match connector shapes and colors to the original
• Route the harness as the OEM diagram specifies and secure with clips or ties to prevent chafing

This replacement switch restores reliable control of a specific circuit or feature in your appliance. A button, selector, or lever that has become unresponsive or intermittent can be fixed by installing a new switch.

• Opens and closes an electrical circuit to power the intended component or feature
• Helps resolve no-response or intermittent operation from a selector or button
• Addresses issues like a stuck/broken actuator or a switch that only works when wiggled
• Supports safe, consistent control of the appliance function

• Disconnect power to the appliance before servicing
• Note wire positions and transfer one lead at a time to the matching terminals
• Seat the switch fully in its mounting; avoid pinching or straining wires
• After reassembly, restore power and test operation; use a multimeter to confirm continuity if needed

The Door Lock Motor and Switch Assembly is an OEM component specifically designed for Frigidaire ranges. This locking system safely secures oven doors during cleaning or self-clean cycles through the electromagnetic operation. 

Symptoms of a defective assembly include: 

• Failure to engage or release the door lock function
• Loud buzzing or grinding noises from internal mechanisms  
• Error codes related to door lock detection problems

Causes relate to wear from continual operation of locking solenoids over extended use. Exposure to cooking residues and cleaning chemicals can deteriorate switches. 

This OEM Frigidaire part is also compatible with some Kenmore and GE appliance brands. Replacing worn components restores reliable door locking to automatically secure during high-heat cycles. Timely maintenance preserves safety functionality.
 

The Inner Door Glass is an OEM part for Whirlpool microwaves. It forms the see-through window that allows for monitoring food as it cooks. The strengthened glass panel is designed to withstand prolonged exposure to steam and heat without issues.

Causes of bad inner door glass can include cracks or chips from accidental drops or impacts, or damage from cleaning chemicals or harsh scrubbing that compromise the glass integrity. 

Symptoms of a bad inner door glass include:

• Cracks or chips in the viewing surface
• Complete breakage leaving a hole in the door  
• Loose or improperly sealed glass panel
• Increased potential for leaks near door seals

This OEM Whirlpool replacement part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore microwaves.

This door hinge supports and pivots the appliance door so it opens smoothly and closes securely. Replacing a worn hinge restores proper alignment and sealing to help the door latch correctly and operate as designed.

• Provides the pivot point and maintains door alignment
• Helps ensure smooth opening/closing and proper latching
• Supports a tight seal to prevent gaps, rattles, or temperature/moisture loss
• Typical failure signs: door sags, binds, squeaks, or won't stay closed/aligned

• Disconnect power before service; wear gloves to protect from sharp edges
• Support the door and control any spring tension; remove mounting hardware and the old hinge
• Install the new hinge in the same orientation; transfer any reusable hardware
• Adjust as needed

This door hinge supports and guides the appliance door so it opens and closes smoothly and stays aligned with the latch and gasket. Replacing a worn hinge restores proper fit and closing action to reduce rubbing and poor sealing.

• Provides the pivot point and supports the door's weight during operation
• Maintains alignment for an even gap and consistent seal
• Helps correct sagging, scraping, or a door that won't close flush
• Common signs of wear: bent/cracked hinge, squeaking or popping, misalignment

• Disconnect power before servicing and support the door to prevent strain or damage
• Remove mounting fasteners; transfer any reusable screws, spacers, or covers from the old hinge
• Install and snug fasteners, then check door alignment and closure; adjust as needed
• Open and close the door several times to verify smooth operation and recheck fasteners

The Microwave Inverter Board is an OEM part for Whirlpool brand microwaves. This board works with the magnetron to convert voltage and power the cooking elements. 

Causes of a bad inverter board can include failure of electronics over time, shorts or current leaks, or improper installation.

Symptoms of a bad inverter board include:

• The microwave will not power on or heat food properly  
• Sparking or burning smells are detected inside the microwave cavity
• The display console does not illuminate or function correctly
• Error codes are frequently displayed

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore models.

Orifice spud secures the burner orifice to the gas valve/manifold and directs fuel to the burner for proper flame performance. Replaces a damaged or corroded spud to help restore correct gas flow at the burner. What it does:

• Holds the burner orifice in place and channels gas from the valve to the burner.
• Helps maintain consistent flame size for even heating and cooking.
• Commonly used when a burner has weak, uneven, or intermittent flame performance.
• Replace if the spud is cracked, corroded, damaged, or leaking.

• Turn off the appliance's gas supply and disconnect power before beginning any repairs.
• Remove burner components per the service manual and install the spud in the same orientation as the original.
• Hand-start threads, then snug with the appropriate wrench—do not overtighten.
• After installation, check fittings for leaks with an approved leak-detection method; if you smell gas or suspect a leak, stop.

This is the glass panel used in the oven door window. Replace it to restore a clear view into the oven and maintain the door's proper heat barrier if the original pane is cracked, shattered, or damaged.

• Forms the viewing window and thermal barrier in the oven door
• Helps the oven retain heat for consistent cooking
• Direct replacement for a cracked, shattered, or missing pane
• Typical symptoms: visible cracks, shattered glass, rattling fragments, or reduced visibility

• Disconnect power or gas and allow the oven to cool completely before service
• Wear cut-resistant gloves and eye protection; handle broken glass with care
• Support the door; remove the door and any trim as outlined in your model's service information
• Transfer any reusable brackets/trim from the original glass and avoid overtightening fasteners

This spark module supplies the high-voltage pulses that ignite the surface burners on a gas cooktop or range. Replacing a failing module helps restore consistent clicking and spark so burners light promptly and reliably.

• Supplies high-voltage to up to five surface igniters (5+0 configuration)
• Sends spark when a burner control is turned to Lite
• Failure symptoms can include no spark on all or multiple burners
• May also cause intermittent/weak spark or continuous clicking

• Disconnect power and shut off gas before servicing
• Note wire locations; move one connector at a time to matching terminals
• Mount securely in the original position and ensure proper grounding
• After replacement, if only one burner won't ignite, inspect that burner's switch and igniter

This oven door hinge restores smooth, controlled movement so the door opens easily and closes fully for a reliable seal. Replacing a worn hinge helps reduce heat loss and supports consistent cooking performance and safe operation.

• Provides the pivot and spring-assisted action for opening and closing the oven door
• Helps pull the door closed and hold it at intended stop positions
• Maintains even gasket contact to keep heat inside the cavity
• Common symptoms of a failing hinge: door won't close fully or sit flush, drops or slams open, binds or pops when moving, or shows an uneven gap

• Disconnect power and allow the oven to cool completely before servicing
• Support the door; open to the removal position and release hinge locks, then lift the door off
• Use caution—hinge springs are under tension; wear hand and eye protection
• Install in the same orientation and verify door alignment and smooth operation after reassembly