Parts for Ge CEB1590SS1SS: 05 - Interior Parts

Binding head screw secures panels and brackets inside your microwave or wall oven. Replace if screw is stripped, missing, or damaged during service.

Truss head tapping screw for microwave assembly. Secures internal components and panels. Replace if screw is stripped, missing, or lost during repair.

Hexagon nut for microwave interior assembly. Secures components and panels in place. Replace if stripped, corroded, or missing during repairs.

Plain washer for built-in microwaves and wall ovens. Replaces worn, missing, or damaged washers during repairs or maintenance. Essential hardware.

Secures the lead wire assembly inside your microwave. Replace if screw is stripped, missing, or no longer holds wiring securely in place.

Back cover panel for your microwave. Installs on the rear of the unit to enclose internal components. Replace if cracked, dented, or missing.

This heater holder is the mounting bracket that secures the oven heating element in place so the element stays aligned for reliable heating and safe operation. It helps prevent movement that can cause uneven cooking or damage. What it does:

• Holds and stabilizes the oven/heater element in the cavity so it stays properly positioned
• Keeps the element from contacting other components, reducing the risk of shorts or damage
• Helps maintain even heat distribution by preventing element sagging or misalignment
• Fits where the element mounts and supports normal operation of the heating circuit

• One heater holder/mounting bracket

• Turn power to the appliance off at the breaker before servicing to avoid shock
• Inspect the element and surrounding insulation for damage when replacing the holder
• Typically secures with screws or clips—retain hardware and note orientation for reassembly

Microwave not heating? High voltage capacitor stores energy to power the magnetron. DIY repair typically takes 30-60 minutes with proper safety care.

The Fuse is an OEM part for GE microwaves. It serves as a safety device designed to protect the microwave from excessive current that can cause overheating and potential fire hazards. When the current flowing through the microwave circuit exceeds a certain level, the fuse blows or breaks, cutting off the power to prevent damage or fire.

Common causes for a fuse to blow include power surges, faulty wiring within the appliance, or the use of microwave inappropriate containers that cause sparks. It is essential to address these issues not only to replace the fuse but also to correct the underlying problems to prevent future failures.

Symptoms of a bad fuse include:

• The microwave suddenly stops working.
• No signs of power or response even when the microwave door is closed and the start button is pressed.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Fixes weak ventilation, excessive noise, or overheating in your microwave. This blower wheel restores proper airflow to clear steam and cool components.

Microwave not heating? The magnetron generates the radiation that cooks food. Moderate DIY repair—discharge capacitor first, then swap 3 screws.

Microwave not heating? A failed diode prevents the magnetron from generating heat. This high-voltage component converts AC to DC power. DIY repair.

Wire harness for microwave ovens. Connects internal electrical components. Replace if wires are frayed, connectors are damaged, or harness is burned.

This temperature thermistor is the sensor that lets the control board monitor and regulate appliance temperature for reliable cooling performance. Replacing a failing thermistor can restore proper temperature control and cycling. What it does:

• Senses internal temperature and sends readings to the control board
• Helps the compressor, fans, and defrost system run at the right times
• Commonly linked to symptoms like incorrect temperatures, overcooling, or frequent on/off cycling
• A faulty thermistor can cause improper defrost timing or erratic cooling behavior

• Disconnect power before inspecting or replacing the sensor to avoid shock
• Handle the sensor and wiring connector gently to avoid damage
• Mount the sensor in the original location and secure wiring per OEM routing

Mounting bracket assembly for microwaves. Installs to secure the microwave in place. Replace if bracket is bent, cracked, or broken during installation.

This heater sheath is the protective metal sleeve that surrounds a dryer/oven heating element, helping protect the element and channel heat where it's needed. It replaces a worn or damaged sheath to restore safe operation. What it does:

• Protects the heating element from physical contact, debris, and shorting
• Helps direct heat flow for consistent heating performance
• Reduces risk of element damage from rubbing or impacts
• Can prevent intermittent heating caused by a compromised sheath

• One heater sheath

• Disconnect power (and gas if applicable) before servicing; follow all safety precautions
• Handle heating elements and terminals carefully to avoid bending or damage
• Basic hand tools required;

Microwave not cooling or fan not running? This fan motor circulates air and cools internal components. Moderate DIY repair in 30-45 minutes.

This motor bracket secures the appliance motor to the housing, keeping the motor stable and aligned for reliable operation. It's a direct-fit replacement designed to restore proper motor positioning and reduce vibration or noise. What it does:

• Holds and supports the motor assembly in the correct position
• Maintains alignment between the motor and driven components (fans, pulleys, etc.)
• Reduces motor vibration and prevents contact with adjacent parts
• Faulty or cracked brackets can cause rattling noises, excessive vibration, or motor misalignment

• Install with power disconnected; follow manufacturer instructions for access and disassembly
• Use the factory mounting hardware and torque specs where specified
• Inspect surrounding mounts and fasteners; replace any worn or damaged hardware

If your microwave turntable wobbles or doesn't rotate smoothly, this shaft ring secures the rotating shaft and keeps components aligned. Quick fix.

Microwave not ventilating or making loud grinding noises? This fan motor restores proper airflow and cooling. Moderate DIY repair with basic tools.

Microwave overheating or shutting off? This motor cooling fan blade circulates air to prevent overheating. Easy 15-minute replacement for most models.