Parts for Ge PSB1200NBB01: 04 - Interior Parts (1) Parts

This motor bracket secures the appliance motor to the housing, keeping the motor stable and aligned for reliable operation. It's a direct-fit replacement designed to restore proper motor positioning and reduce vibration or noise. What it does:

• Holds and supports the motor assembly in the correct position
• Maintains alignment between the motor and driven components (fans, pulleys, etc.)
• Reduces motor vibration and prevents contact with adjacent parts
• Faulty or cracked brackets can cause rattling noises, excessive vibration, or motor misalignment

• Install with power disconnected; follow manufacturer instructions for access and disassembly
• Use the factory mounting hardware and torque specs where specified
• Inspect surrounding mounts and fasteners; replace any worn or damaged hardware

This circulation motor drives the refrigerator/ freezer evaporator fan to keep cold air moving through the appliance, helping maintain even temperatures and efficient cooling. Replaces a failed or noisy evaporator fan motor. What it does

• Spins the evaporator fan blade to circulate cold air through the freezer and refrigerator compartments.
• Restores proper airflow when a unit is warm or cooling unevenly.
• Stops or reduces excessive noise when a worn or failing motor is replaced.
• Helps prevent frost buildup caused by poor air circulation.

• Disconnect power to the appliance before beginning any repair.
• Handle the fan blade and motor shaft carefully to avoid bending or damaging components.
• Verify mounting orientation and electrical connector fit before final assembly.

This NTC thermistor is a temperature sensor that feeds real-time temperature data to the control. Replacing a failing sensor helps restore accurate temperature regulation, reduce nuisance shutdowns, and improve consistent cycle timing and performance.

• Monitors temperature by changing resistance as heat rises or falls
• Sends a signal to the electronic control to manage heating and fan operation
• A failed sensor can cause inaccurate temperatures, short/long cycles, or sensor-related error messages
• May prevent certain cycles from starting

• Disconnect power and allow the appliance to cool completely before servicing
• Note connector orientation and wire routing; take a photo for reference
• Install the sensor in the original location/clip and route wires away from hot or moving parts
• Restore power and run a test cycle to proper temperature response

This is the oven thermostat that senses and controls the oven cavity temperature so your range heats to and maintains the set temperature for baking and roasting. Replacing a faulty thermostat can restore consistent, accurate cooking performance.

• Regulates oven temperature by cycling the heat source on and off
• Helps correct issues like oven not reaching set temperature or running too hot
• Can address erratic temperature swings or uneven baking results
• Mechanical control with sensing bulb/capillary that monitors oven heat

• Disconnect power and allow the oven to cool completely before service
• Handle the capillary/sensing bulb carefully—do not kink, bend sharply, or cut it
• Route and secure the capillary in the original clips/position to avoid hot spots
• Verify knob alignment and perform a test preheat; adjust calibration only per service guidance

A temperature sensor assembly that monitors internal temperatures and sends readings to the appliance control so the unit can maintain proper heating or cooling. Replacing a failed sensor restores accurate temperature regulation and consistent performance. What it does

• Detects and reports temperature to the electronic control or thermostat
• Helps the appliance maintain set temperatures for consistent operation
• A faulty sensor can cause inaccurate temperature readings or uneven heating/cooling
• May trigger temperature-related error codes or put the unit into a diagnostic/fail-safe mode

• Disconnect power to the appliance before attempting any repair
• Handle the sensor and its wiring gently; avoid bending or damaging the sensing tip or connectors
• Reconnect wiring securely and confirm correct routing to prevent interference with moving parts

This heater sheath is the metal protective tube that surrounds and secures a dryer's heating element, helping protect the element from abrasion and keeping heating airflow directed for reliable drying performance. What it does:

• Protects the heating element from contact and physical damage during operation
• Helps maintain proper airflow around the element for consistent heat distribution
• Reduces risk of element grounding or shorting caused by contact with other parts
• Can address symptoms like sputtering or uneven heating, burning/metallic smells, or visible damage to the element area

• 1 heater sheath

• Power off and unplug the appliance before service to avoid shock or injury
• Inspect the heating element and mounting hardware while replacing the sheath; replace any damaged parts
• Handle the sheath and element carefully—sharp edges may be present; wear gloves and eye protection