Parts for Ge PSB1200NBB01: 03 - Oven Cavity Parts

This adhesive foam seal tape provides a slim, flexible sealing strip used to restore a tight seal around appliance openings. It helps reduce air leaks, moisture intrusion and improves temperature stability for refrigerators and freezers. What it does:

• Creates a compressible, airtight seal where original foam tape has worn or separated
• Helps reduce warm air infiltration and frost buildup that can affect cooling performance
• Minimizes moisture and dust entry at door edges or panel seams
• Restores contact between mating surfaces to improve energy efficiency

• Clean and dry the mounting surface thoroughly before applying for best adhesion
• Measure and trim tape to fit; peel backing and press firmly in place along the seam or edge
• Replace only the lengths required; avoid stretching the tape during installation
• Disconnect power or follow manufacturer safety guidance

Replacement flat housing case for microwaves. Secures internal components and restores proper panel alignment. Replaces cracked, broken, or missing cases.

This door switch access cover replaces the plastic access panel that protects and secures the door latch/switch assembly behind the appliance door. It restores a finished appearance and helps keep the switch area safe and stable. What it does:

• Covers and secures the door switch area to prevent debris contact and accidental interference
• Helps maintain proper alignment of the door switch and latch components
• Stops light drafts and reduces rattles around the door switch opening
• Common symptom: cracked, broken, or missing cover causing loose switch or exposed switch components

• Disconnect power (unplug or switch off breaker) before starting any repair
• Remove the door inner panel or trim as needed to access the switch area; retain fasteners for reassembly
• Align cover over the switch opening and secure with the original screws/clips; do not overtighten
• If any switch or latch parts are damaged, inspect and replace those components separately

This right-side trim piece restores the finished edge and appearance of the appliance door, covering the seam and protecting the edge from chips and wear. It matches OEM fit and finish for a clean look. What it does:

• Covers and protects the right edge of the door or panel to prevent chips and dings
• Restores finished appearance where trim is cracked, missing or discolored
• Helps keep the door edges aligned and conceals mounting seams
• Matches the OEM contour and mounting points for proper fit

• Disconnect power or follow manufacturer safety instructions before starting
• Remove the door or access panel per the service manual for easiest installation
• Align mounting tabs and press or fasten in place with original screws/clips
• Handle trim carefully to avoid scratching the finished surface

This left-side black trim piece replaces a damaged or worn decorative edge to restore the appliance's finished appearance and help protect the cabinet opening from wear. What it does:

• Covers and protects the left edge of the appliance opening for a clean, finished look
• Replaces cracked, scratched, or faded trim that affects appearance
• Helps keep debris out of the gap between the appliance and cabinetry
• Matches the original black finish for a consistent appearance

• One left-side black trim piece as shown

• High-level replacement part—require removing adjacent trim or panels for access
• Use proper hand tools; avoid overtightening fasteners to prevent cracking
• Disconnect power to the appliance before accessing internal components or wiring
• If mounting clips or screws are missing or damaged, replace them with OEM-specified hardware

White bottom plate for your microwave interior. Replaces cracked, stained, or damaged base plates. Restores clean appearance and supports food rotation.

The Plate Bottom is an OEM part for GE microwave ovens. It forms the base surface area that internal microwave components are securely mounted and attached to. 

Causes of failure include warping and cracking of the metal shelf from prolonged exposure to high temperatures.  

Symptoms of a bad plate bottom include:

• Visible distortions or cracks in the metal material  
• Loose mounting locations for interior assembly parts
• Air gaps impairing heat dissipation from components  
• Eventual failure of attached parts over long term use

This OEM GE replacement is also compatible with Hotpoint, RCA and select Kenmore microwave models.

Support bracket that secures internal components and keeps assemblies aligned in microwaves. Replace if cracked, broken, or missing to restore fit.

The Canopy Mica is an OEM part for GE microwaves. This part covers the waveguide channel, preventing food particles and grease from entering the microwave's internal mechanisms.  

Causes of a bad canopy mica can include exposure to high levels of moisture or grease, physical damage such as cracks or burns, and general wear and tear over time.  

Symptoms of a bad canopy mica include:

• Sparks or arcing during microwave operation
• Burn marks or discoloration on the mica sheet
• Unusual noises while the microwave is running
• Uneven cooking or heating of food

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Fix a microwave turntable that won't spin or turns intermittently. This motor drives the glass tray for even heating. DIY repair in 20 minutes or less.