Parts for Lg LRE6383ST/00: Introduction Parts

A Tap-Tite binding-head screw used to fasten appliance panels and components where a self-tapping metal thread is required. Replaces missing or damaged fasteners to restore secure assembly and reduce vibration or rattling. What it does:

• Creates its own mating thread in thin sheet metal for a secure hold without a nut.
• Holds panels, brackets, and trim in place to prevent looseness or movement.
• Commonly used where stripped, missing, or broken screws cause rattling, misalignment, or parts that won't stay attached.
• Compatible with standard screwdrivers or nut drivers sized to the binding-head.

• Disconnect power and unplug the appliance before working on it.
• Use the correct driver bit to avoid cam-out or head damage.
• Start straight and apply steady pressure; avoid overtightening to prevent stripping the formed threads.
• If the original hole is badly damaged, assess for repair or use of a larger fastener as needed.

A factory screw for securing specified components in your appliance. Replaces a missing or damaged fastener to restore a tight, reliable hold and help reduce vibration, rattling, and misalignment.

• Secures brackets, covers, or internal assemblies where this exact screw is specified by the manufacturer
• Useful when the original screw is missing, stripped, or corroded
• Helps eliminate looseness, vibration, and rattling noises
• Matches the original fastener for proper fit and thread engagement

• Disconnect power (and shut off water supply if applicable) before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace any damaged clips or inserts to ensure a secure repair

This customized washer is a small hardware piece that secures fasteners and helps distribute load where screws or bolts attach to appliance components. It restores proper fit and reduces movement at the connection point. What it does:

• Provides a stable bearing surface for screws or bolts to prevent pull-through and material damage
• Helps keep fasteners tight and reduces vibration-related loosening or rattling
• Maintains correct spacing and alignment of panels or internal parts
• Can help form a seal on fasteners in locations prone to vibration or minor movement

• Disconnect power and water (if applicable) before servicing the appliance
• Retain or replace the associated fastener; small parts can be easily lost—work on a clean surface

This factory-specified fastener secures designated panels and components, restoring a precise fit and helping keep your appliance solid and quiet. Replace a missing, stripped, or rusted original with the correct OEM match for the specified locations.

• Secures brackets, panels, and internal parts where this part number is called out
• Replaces damaged, stripped, corroded, or lost screws
• Helps reduce looseness and vibration that can cause rattling noises
• Exact OEM replacement for positions requiring this specific screw

• Disconnect power and shut off water/gas before servicing
• Match to the removed screw and install only in the locations specified for this part number
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening, especially into plastic
• If multiple screws are involved, start all fasteners before final tightening to ensure alignment

This customized screw secures appliance components where a standard fastener won't fit, helping keep panels, brackets and small assemblies stable. It's a direct-fit replacement when the original specialized screw is missing or damaged. What it does:

• Fastens and holds appliance panels, brackets or small parts in place
• Prevents rattling, loose trim or misaligned components caused by a missing or stripped screw
• Matches the OEM fit and thread pattern for proper engagement and alignment
• Used in locations that require a non-standard or customized fastener

• Disconnect power and water before servicing the appliance
• Use the correct screwdriver or driver bit to avoid stripping the head
• Tighten securely but do not overtighten; overtightening can strip threads or crack parts
• Keep removed hardware organized so you can reinstall in the original location

This hardware washer helps distribute fastener load and maintain proper spacing in your LG appliance. Replacing a missing or worn washer restores secure mounting and alignment, reducing vibration and rattling from loose assemblies.

• Distributes the load of a screw or bolt and protects mating surfaces to maintain alignment
• Helps keep components secure and at the correct spacing
• A damaged or missing washer can lead to loosening, vibration, or rattling during operation
• Ensures correct hardware stack-up during reassembly after service

• Disconnect power and shut off water or gas before servicing
• Note the order and orientation of any washers/spacers; take a reference photo
• Use the correct driver or wrench and tighten snugly—do not overtighten
• Replace companion hardware if corroded, stripped, or damaged

The Common Nut is an OEM part for LG ranges. It secures the fan blade to the motor shaft. This nut maintains the fan's stability and preventing it from becoming dislodged during use.

Causes of a bad common nut can include loosening over time due to vibration, improper installation, or damage from impact or mishandling.

Symptoms of a bad common nut include:

• Excessive noise or vibration from the fan assembly
• The fan blade becoming loose or detached, causing poor air circulation
• Potential risk of the fan blade becoming a projectile if completely detached

This OEM LG part is also compatible with some Kenmore models.a

This idler bracket secures the idler in the drive system, keeping the belt aligned and properly tensioned for smooth operation. Replacing a bent or worn bracket helps reduce noise and restore consistent belt tracking.

• Holds the idler in position to maintain proper belt tension and alignment
• Helps prevent belt slippage, squealing, or scraping noises
• A bent, cracked, or loose bracket can cause the belt to come off or loss of drive motion
• Visible wear or misalignment around the idler mount is a common replacement indicator

• Disconnect electrical power; if applicable, shut off gas supply before servicing
• Access the drive system and relieve belt tension before removal
• Transfer the idler pulley and spring (if applicable) to the new bracket
• Reinstall in the original orientation and verify correct belt routing and alignment before test run

This replacement door handle restores a secure, easy-grip opening to your refrigerator door. It matches the OEM shape and mounting points so the door operates smoothly and looks factory-fresh. What it does:

• Replaces a cracked, loose, or broken refrigerator door handle so the door is easier and safer to open.
• Restores proper grip and leverage for normal daily use.
• Reinstalls to existing factory mounting points to maintain door alignment and appearance.
• Helps prevent further cabinet or door damage caused by using a compromised handle.

• One refrigerator door handle

• Requires removing the old handle and securing the replacement to the same factory screw bosses; use the original screws unless new hardware is explicitly listed.
• Handle hardware may be hidden under trim—check for set screws or clips before prying.
• Support the door while working to avoid strain on hinges; two-person assistance recommended for larger doors.
• Disconnect power only if required for surrounding panels—this is an exterior handle replacement and typically does not require electrical disconnection.

Replacement window glass that restores a clear viewing area in the appliance door and helps maintain a clean, sealed surface. Ideal for replacing cracked, chipped, or cloudy glass to improve visibility and safety. What it does:

• Provides a transparent viewing window so you can monitor cycles without opening the door.
• Replaces cracked, chipped, or fogged glass to restore appearance and function.
• Serves as the door's viewing surface and works with the door assembly and trim.
• Inspect surrounding gaskets, trim, and fasteners when replacing the glass to ensure a proper fit.

• Disconnect power (and water, if applicable) before attempting any repair.
• Wear cut-resistant gloves and eye protection when handling or removing glass.
• Door disassembly and removal of trim or retaining clips is commonly required.
• If the glass is shattered, remove broken pieces carefully and dispose of them per local regulations.

This insulator is a small cushion pad that reduces noise, vibration and wear by isolating internal components from the appliance cabinet. It helps protect wiring and parts from rubbing and shorting while improving overall operation comfort. What it does:

• Cushions components to reduce rattling, buzzing and vibration-related noise
• Provides electrical insulation to help prevent shorts where fitted near wiring or terminals
• Protects surfaces and components from wear caused by rubbing or contact
• Helps maintain correct spacing of internal parts for reliable operation

• Disconnect power and unplug the appliance before starting any repair
• Access may require removing exterior or interior panels—keep fasteners organized
• Position the insulator exactly as shown in the appliance diagram; do not compress or overly stretch
• If adhesive is present, replace with equivalent high-temperature adhesive or use OEM replacement clips as specified

Hinge assembly that secures and pivots the appliance door for smooth, stable operation. Restores proper alignment and sealing to reduce sagging, rubbing, and help the door close evenly. What it does:

• Supports and guides the door pivot to maintain correct opening and closing motion.
• Restores proper door alignment and sealing to improve performance and reduce leaks or cold spots.
• Reduces sagging, rubbing, and noisy or stiff door movement.
• Helps the door latch and close evenly for reliable use.

• Always disconnect power (and water supply, if applicable) before starting repairs.
• Support the door before removing the old hinge to prevent dropping or damage.
• Use appropriate hand tools; avoid forcing parts and do not overtighten fasteners.

The Main PCB Assembly is an OEM part for LG electric ranges. This printed circuit board plays a vital role in communicating between electronic components and the control panel to execute cooking commands and temperature settings.

Causes of a bad main board can include damage to printed circuits from power surges or shorts, degradation of electronic pathways over time, or failure of individual components like microprocessors, capacitors, or resistors.  

Symptoms of a bad main board include:

• Temperature and timer display not working 
• Inability to select bake, broil, or convection modes
• Ignition or valves not engaging for surface burners  
• Oven continually heating to incorrect temperature levels
• Fault or error codes appearing frequently

This precision-engineered LG board restores full cooking control and capability. Compatible models include some Kenmore ranges. 

This part is an oven control board. It's manufactured by LG. The oven control board includes the display that shows the time, temperature, and oven functions. It is designed to be durable, but can short out because of a power surge. The control board can also be damaged through exposure to moisture or high heat, and through physical impact.Replacing the oven control board will require turning off the power to the oven and removing the metal cowl that covers and protects the board. Take note of the wire harness positions on the board. Remove the wiring clips, unscrew the mounting screws, and remove the old board.This genuine OEM part is sold individually. It is only designed to work with LG ovens.

The Display PCB Assembly is an OEM part for LG ranges. This part controls and displays the digital interface of the range, providing users with important information such as temperature settings, cooking modes, and timers.

Causes of a bad display PCB assembly can include electrical surges, moisture damage, or general wear and tear over time. 

Symptoms of a bad display PCB assembly include:

• The display not lighting up or being dim
• Inaccurate or scrambled information shown on the screen
• Unresponsive touchpad or buttons
• Error codes appearing without an apparent cause

This OEM LG part is also compatible with some Kenmore models.

This Supporter is a replacement mounting bracket designed to secure internal components and restore proper alignment, helping reduce noise and prevent part movement. Durable, factory-compatible fit for reliable operation. What it does:

• Provides structural support for adjacent components to maintain correct positioning
• Helps eliminate rattling or shifting caused by worn or broken supports
• Restores secure mounting after damage or during part replacement
• Compatible with OEM mounting points and fastener locations

• Disconnect power and unplug the appliance before attempting any repair
• Use the original fasteners where possible; replace damaged hardware as needed
• Minimal hand tools are typically required; avoid overtightening to prevent plastic stress

This single wire harness connects controls and components to deliver power and signals so affected functions run correctly. It replaces a damaged harness to restore reliable electrical connections and consistent operation. What it does:

• Transfers power and control signals between the control board and individual components
• Restores missing or intermittent power to components when a harness is damaged
• Prevents shorts and poor connections caused by frayed wires or broken terminals
• Typical symptom: appliance or specific functions do not power up, run intermittently, or behave erratically

• Disconnect power to the appliance before starting any work.
• Match connector shapes and wire colors; seat each connector fully until it clicks.
• Route the harness following existing clips and retainers to avoid chafing or pinching.
• If terminals are corroded or connectors are damaged, replace the harness rather than attempting repairs.

This single wiring harness connects electrical components to restore reliable power and signal routing within the appliance. It replaces damaged or burnt harnesses to help return normal operation and prevent intermittent faults. What it does

• Routes power and signal between control boards, sensors, and motors for proper operation
• Replaces frayed or melted wiring that can cause intermittent function or component failures
• Helps resolve symptoms like no power to a component, intermittent operation, or error codes related to open circuits
• Restores factory wiring organization and secure connector fit for reliable connections

• One wiring harness assembly

• Disconnect power before servicing to avoid shock or damage
• Verify connector orientation and fully seat all plugs; do not force connectors
• Replace only with the exact harness to maintain correct wire lengths and connector types

A circular lug designed to join a stripped wire to a threaded terminal for a secure electrical connection. Helps restore reliable contact at terminals and reduces the chance of intermittent power or arcing at connection points. What it does:

• Provides a strong mechanical and electrical connection between a wire and a screw or bolt terminal.
• Helps prevent loose connections that can cause intermittent operation, sparking, or overheating.
• Commonly used where a ring-style termination is required for safe, stable wiring.
• Works with properly sized wire and fasteners to maintain consistent conductivity.

• Always disconnect power to the appliance before inspecting or replacing electrical parts.
• Use the correct lug size and gauge for the wire and terminal; crimp or solder per manufacturer recommendations.
• Tighten terminal hardware to the appliance manufacturer's specified torque; avoid over-tightening which can damage the lug or terminal.
• If wiring insulation or the terminal is damaged or corroded, replace the affected components rather than reusing them.

The HARNESS, SINGLE is an OEM component specifically designed for LG ranges. It is a custom wiring assembly that electrically connects critical range functions such as ignition, valve operation, and thermostats/sensors. Proper signal transmission through this single integrated harness is essential for safe and effective cooking performance.

Causes of a bad single gas harness can include damaged insulation from abrasion over time or loose connections disrupted by normal range movement. Physical impacts or overheating could also degrade individual harness wires. 

Symptoms of a bad single harness include:

• Inability to ignite burners or light doesn't stay lit 
• Burners failing to turn off automatically  
• Faulty burner temperature control
• Error codes or safety issues triggering range lockouts

Replace yours today with this genuine OEM wiring harness to ensure all range systems communicate reliably. This ensures your LG gas range remains durable and dependable for years to come.

This heater assembly replaces the dryer's heating unit to restore warm air for effective drying. It fits into the dryer's blower/air path and provides the heat source needed to evaporate moisture from clothing. What it does:

• Houses the heating element and directs warm air through the drum
• Restores normal drying temperatures when the original heater fails
• Common symptom: dryer runs but clothes remain damp or take much longer to dry
• Common symptom: reduced or no warm air coming from the dryer

• Disconnect power (and gas supply for gas models) before beginning any repair
• Handle heating elements and terminals carefully to avoid damage
• After installation, test dryer operation and check for proper airflow and secure electrical connections

This glass turntable plate supports food inside the microwave and provides a stable, heat-resistant surface for even cooking. It replaces a cracked, chipped, or missing tray so meals rotate smoothly during use. What it does:

• Provides a flat, heat-safe surface for plates, bowls, and cookware
• Enables the turntable mechanism to rotate food for more even heating
• Replaces damaged or shattered glass that can catch or crack further
• Reduces rattling or scraping caused by a broken or warped tray

• One round glass turntable plate

• Handle with care; glass can break if dropped or hit
• Clean with warm, soapy water and avoid sudden temperature changes
• Ensure the plate is seated properly on the roller ring and drive hub before use
• Disconnect power to the appliance before inspecting internal components

This heater bracket is a metal mounting support that holds the appliance's heater or heating element securely in place, helping maintain proper alignment and reduce movement. Replacing a bent or broken bracket restores stable support for the heater assembly. What it does:

• Secures the heater or heating element to the appliance frame so the element stays aligned and does not contact other components.
• Prevents rattling, shifting, or sagging of the heater assembly that can cause noise or uneven heating.
• Helps maintain safe clearances between the heater and surrounding parts.
• Used when the original bracket is cracked, bent, or missing hardware.

• Disconnect power (and gas, if applicable) before beginning work to avoid electrical shock or gas hazards.
• Handle metal parts carefully — edges may be sharp. Wear gloves and eye protection.
• Match the part number and orientation, secure all fasteners, and ensure the heater is properly aligned before restoring power.

This radiant surface element fits beneath the glass cooktop and delivers direct, even heat to your cookware. Replace a burned-out or damaged burner to restore consistent heating when a smoothtop zone no longer performs correctly.

• Generates radiant heat under the ceramic-glass surface for a surface burner
• Helps resolve no-heat, very slow/uneven heating, or only part of the element glowing
• Restores reliable temperature control when a cooking zone won't respond to settings
• Suitable replacement when burn marks or breaks are visible beneath the glass

• Disconnect power at the breaker and let the cooktop cool completely before servicing
• Lift or remove the glass top to access the element; note and label wire positions
• Handle the element carefully; avoid flexing the coil or disturbing insulation
• Transfer any mounting clips/brackets from the old element if required, then reassemble and test

This Radiant Surface Element is an OEM replacement part for LG electric ranges and cooktops. It is a high-power coil heating unit located below the cooktop surface that provides efficient, customizable heat for various cooking needs.

Causes of failure can be wear and damage to coiled filaments from prolonged heating cycles, cracking of ceramic insulators, or loose wiring connections suffering arcing or resistance over time.

Symptoms of a faulty element include:

• Slow or inadequate heating of cookware even on high settings
• Temperature fluctuations within the heating zone
• Burning or charring of spills and foods on the element itself
• Tripped circuit breakers obstructing range operation

This replacement is also compatible with some Kenmore models

This radiation heater is the element that delivers direct radiant heat for the microwave's grill/browning feature. Replacing a failed heater restores proper grilling performance and helps foods brown and crisp during grill or combination-cook settings. What it does:

• Supplies radiant heat for grill/browning and combo-cook modes
• Typically mounted at the top of the cavity to radiate heat downward
• Common failure symptoms: no heat in grill mode, element does not glow, poor or uneven browning
• Visual clues can include cracks, blistering, or burnt spots on the heater

• 1 radiation heater element

• Disconnect power before servicing; microwaves contain high-voltage components that can retain a charge even when unplugged
• Access may require removing the outer case and interior shroud; beware of sharp metal edges
• Note wire positions before removal; route leads away from hot or moving parts during reassembly
• Verify secure mounts and connections before testing the grill function

This small, board-mounted tactile push-button switch is used on the control panel. It registers a momentary press so the control board can accept your selection. Replacing a worn switch restores reliable button response and consistent operation.

• Mounts to the user interface board and provides momentary contact when a button is pressed
• Sends a low-voltage signal to the control, enabling cycle or option selection
• Typical failure symptoms: unresponsive or intermittent buttons, needing extra force to register, stuck/always-on input, or unintended beeps/changes
• Helps restore consistent user-interface input when an individual button switch has failed

• Disconnect power to the appliance before servicing; shut off gas/water if applicable
• Access the control panel to reach the user interface board
• This is a board-level repair; note switch orientation. Replacement may require desoldering/soldering per OEM procedure
• Use ESD precautions and avoid overheating PCB pads; test button function before reassembly

The MOTOR, AC FAN is an OEM part for LG refrigerators, designed to circulate air efficiently throughout the unit. This vital component ensures that cool air is distributed evenly across the refrigerator and freezer compartments, aiding in maintaining consistent temperatures to keep food fresh and prevent spoilage. 

Causes of a bad MOTOR, AC FAN can range from wear and tear over time, dust and debris accumulation impeding the motor's function, to electrical malfunctions preventing the motor from operating.

Symptoms of a bad MOTOR, AC FAN in a refrigerator include:

• Inconsistent or warming temperatures within the refrigerator or freezer compartments
• The refrigerator running longer than normal or working harder to maintain cool temperatures
• Unusual noises suggesting the fan motor is struggling to operate or has failed

This OEM LG part is also compatible with some Kenmore models.

The Magnetron Thermostat is an OEM part for LG microwaves and built-in ranges. Its primary function is to monitor the temperature and ensure that it remains within a safe operating range. If the temperature exceeds the preset limit, the thermostat will interrupt the power supply to the magnetron, preventing overheating and potential damage.

Causes of a faulty magnetron thermostat can include electrical malfunctions, component failures, or physical damage. These factors can result in issues such as erratic heating, microwave not heating properly, or the appliance shutting off unexpectedly.

Symptoms of a bad magnetron thermostat may include:

• Microwave not heating food evenly or at all
• Inconsistent or weak heating performance
• Microwave shutting off or displaying error codes related to temperature issues

This OEM LG part can also be used on Kenmore/Sears appliances. 

The Thermistor is an OEM replacement part for LG gas ranges. It serves as a highly sensitive temperature sensor mounted inside the oven cavity. 

Symptoms of a bad thermistor include:  

• Inability to select certain cooking modes like bake or convection that involve temperature control
• Fluctuating or inaccurate temperature readouts on oven displays
• Irregular cooking outcomes like hot/cold spots inside the oven
• Repeated error codes regarding temperature sensing issues

Causes can be attributed to prolonged exposures to heat and intermittent combustion byproducts inside the oven. Over a decade of use, these conditions may degrade the thermal and electrical properties of sensor components. 

This genuine LG replacement thermistor installs effortlessly. Installing a new thermistor restores temperature monitoring required for reliable gas oven performance. 

A replacement bracket assembly that secures internal components and maintains correct alignment for reliable operation. Restores proper mounting and reduces noise or movement caused by loose or damaged supports. What it does:

• Provides a secure mounting point for internal appliance components to prevent shifting or sagging
• Restores alignment that can stop rattling, vibration, or intermittent contact issues
• Supports housings, panels or subassemblies to maintain proper clearance and function
• Replaces bent, cracked, or broken brackets that compromise component stability

• One bracket assembly as shown

• Recommend disconnecting power (and water, where applicable) before beginning any repair
• Remove panels or covers as needed to access the mounting location; keep fasteners organized
• Use appropriate hand tools; inspect adjacent parts and replace any damaged fasteners or clips

The PCB Assembly is an OEM part for LG washing machines. This Printed Circuit Board (PCB) controls the electrical functions of the washer, managing the various cycles and ensuring proper operation of the machine.

Causes of a bad PCB assembly can include electrical surges, moisture damage, or wear and tear over time affecting the electronic components.

Symptoms of a bad PCB assembly include:

• The washing machine not starting or stopping unexpectedly
• Error codes displaying on the control panel
• Inconsistent or incomplete wash cycles
• The washer not responding to control inputs

This OEM LG part is also compatible with Sears/Kenmore models.

This replacement bar serves as the exterior door handle/trim that lets you open and close the appliance door smoothly while restoring the unit's original appearance. It's a direct-replacement style part designed to fit the factory mounting points. What it does:

• Provides a secure grip for opening and closing the appliance door
• Restores damaged, cracked, or cosmetically worn door trim/handle areas
• Helps maintain proper door alignment and fit when installed correctly
• Reduces draft and keeps the door sealing surface operating as intended

• One replacement bar

• Disconnect power (and for refrigerators, unplug the unit) before attempting removal/installation
• Remove any door shelves or trim blocking access; support the door during handle removal to avoid damage
• Reuse any required screws or brackets only if shown in OEM instructions; replace damaged fasteners

AC synchronous motor assembly that turns the appliance's rotating components to restore normal operation. Replace this motor if the appliance fails to spin, spins intermittently, or produces unusual humming or grinding noises. What it does:

• Replaces the appliance's worn or failed AC synchronous motor to restore rotation and proper function.
• Helps address symptoms such as no rotation, intermittent spinning, humming, grinding, or failure to start.
• Connects to the existing motor mounting and electrical connectors as a direct replacement when the part numbers match.
• Matches OEM function and electrical type (AC synchronous) for compatible appliance platforms.

• Always disconnect the appliance from power before starting any repair.
• Remove the appropriate access panels to reach the motor; support any heavy components (drum/rotator) while you work.
• Verify that the motor's wiring connectors and mounting points match the original before final installation.

This supporter is a small mounting support used to stabilize and secure nearby components within the appliance, helping reduce vibration and maintain proper alignment for reliable operation. What it does:

• Provides structural support for an internal assembly or panel
• Helps keep linked components aligned and reduces rattling or vibration
• Restores proper fit where a worn or broken support causes looseness
• Supports normal operation by holding parts in their intended position

• One supporter mounting support

• Intended for replacement of a single damaged or missing support; verify part location before ordering
• Turn off and unplug the appliance (or shut off power) before servicing
• Use appropriate hand tools; avoid over-tightening fasteners to prevent cracking

This terminal block connects the appliance power cord to the internal wiring, providing a secure, insulated point for line voltage. Replacing a worn or damaged terminal block restores a stable electrical connection and reduces arcing risk. What it does

• Secures incoming power leads and routes line voltage to the appliance wiring
• Prevents loose or intermittent power caused by cracked or burned terminals
• Helps stop visible sparking or overheating at the cord connection
• Supports strain relief so the power cord stays positioned correctly

• Disconnect power at the breaker or unplug the appliance before starting work
• Verify power is off with a meter; handle live wiring only
• Note wire placement and orientation before removal; transfer wires to the new block in the same order
• Tighten terminal screws securely and restore any strain-relief hardware

This incandescent oven lamp provides interior illumination so you can safely check food without opening the door. Direct replacement for a burned or dim oven/range light to restore cooking visibility. What it does

• Replaces a burned-out or flickering oven interior light bulb
• Restores clear visibility of the oven cavity for monitoring cooking progress
• Helps avoid opening the oven door unnecessarily, preserving oven temperature
• Fits the original lamp socket and installs in the oven light housing

• Disconnect power to the appliance before replacing the lamp to prevent electric shock
• Allow the oven and old bulb to cool completely before handling
• Use a cloth or gloves when installing the new lamp to avoid transferring oils from skin

The Broil Element is an OEM replacement part for LG electric ranges. As a vital upper heating system, this broil element helps efficiently brown and crisp foods placed directly under or on the top rack of the oven.

Causes of a defective broil element may relate to normal wear and tear on the coils from repeated high-heat cooking. Food residues adhering over time can reduce performance.

Symptoms of a problematic broil element include:

• Inadequate or uneven browning from the top-level heating system   
• Diminished functionality of the broil setting on the control panel
• Potential thermal damage or exposed wiring from a failed element

This OEM component fits some Kenmore/Sears electric range models as well. 

The Bake Element is an OEM replacement part for LG wall ovens and ranges. It is responsible for providing heat during the bake functions.

Symptoms of a bad bake element include:

• Inconsistent or unreliable bake temperatures
• Hot/cold spots leading to uneven cooking results
• Premature failure of bake cycles or overload tripping

Causes can be normal wear over thousands of heating cycles. Improper cleaning allowing residue buildup may also degrade element performance prematurely. Accurate, dependable heat is required for successful baking.

This OEM LG part is also compatible with Kenmore and Frigidaire wall ovens and ranges.

This sheath heater is the electric element that delivers radiant heat for the unit's heating cycles, such as grill/broil or convection. Replacing a failed heater restores proper temperature performance and consistent results.

• Generates radiant heat when energized to help reach and maintain set temperature
• Supports grill/broil or convection functions for browning and even cooking
• Common failure signs: no heat in those modes, extended preheat times, uneven results, tripped breaker, or a visibly blistered/broken element
• Restores reliable heating performance when the original element is open or shorted

• Disconnect power and let components cool before servicing
• If servicing a microwave, remember high-voltage components can retain a dangerous charge; discharge the capacitor and consider service if you're not experienced
• Handle the element by its brackets; avoid bending the sheath or stressing terminals
• Move wires one at a time to the new part and verify element continuity with a multimeter before reassembly

This control panel assembly is the front user interface that holds the touchpad/buttons and display, restoring responsive controls and a finished look to the appliance. It replaces a cracked, faded, or unresponsive front control surface. What it does

• Provides the front-mounted buttons/touchpad and display lens used to select cycles and functions.
• Routes user input to the appliance's control electronics so commands register correctly.
• Restores a damaged, cracked, or scratched control surface that interferes with button use.
• Helps address symptoms such as unresponsive or stuck buttons, missing or obscured markings, and visible panel damage.

• One control panel assembly (front user interface)

• Disconnect power to the appliance before beginning work to avoid shock.
• Remove outer trim or screws as needed; handle the display lens and ribbon cables gently to avoid damage.
• Keep small screws and clips organized during disassembly; reconnect all cables securely before reassembly.

This foot is a small rubber base pad that supports and stabilizes the appliance on the countertop or cabinet surface. Replacing a worn or missing foot helps keep the unit level and reduces vibration and slipping.

• Provides stable, non-slip support on flat surfaces
• Helps keep the appliance level for proper operation
• Replaces missing, cracked, or flattened feet
• Can reduce vibration, rattling, or shifting during use

• Unplug the appliance before servicing
• Turn the unit on its side/back for access to the base
• Pull off the old foot and press the new one firmly into place (some models may use adhesive or a tab fit)
• Verify the unit sits level; replace additional feet as needed

This replacement slider restores smooth, guided movement for the appliance component it mounts to, helping reduce sticking, binding and noise. A simple, low-cost part that returns parts to proper alignment and operation. What it does:

• Guides and supports a moving panel or drawer to ensure even, low-friction travel
• Reduces binding, catching or noisy movement when the original slider is worn or damaged
• Keeps the associated component aligned to prevent uneven wear or mis-tracking
• Helps restore normal operation without replacing larger assemblies

• One replacement slider

• Disconnect power to the appliance before beginning any repair
• Remove the affected panel/drawer per the appliance service instructions to access the slider
• Inspect surrounding tracks or mounting tabs for damage and replace if necessary
• Test movement after installation; if binding persists, re-check alignment

This slider is a replacement glide piece that helps a drawer or sliding compartment move smoothly and stay aligned. Replacing a worn slider restores quiet, consistent travel and prevents wear on the surrounding trim. What it does:

• Guides and supports a drawer or sliding compartment for even movement
• Reduces sticking, scraping, and noisy operation from worn glides
• Keeps the drawer aligned to prevent rubbing or binding against the cabinet
• Helps extend life of associated rails and trim by restoring proper tracking

• One slider glide piece

• Disconnect power to the appliance and remove any contents before servicing
• Remove the drawer or access panel per your appliance instructions to reach the slider
• Inspect mating rail and fasteners; replace any damaged clips or screws for a secure fit

This door handle mounting anchor creates the fixed attachment point on the appliance door or drawer. Replacing a worn or missing anchor restores a solid, wobble-free handle and a consistent feel when opening and closing.

• Provides the secure mounting point that the handle fastens to
• Helps keep the handle aligned and rigid during use
• Replace if the anchor is cracked, stripped, or missing
• Resolve a loose/wobbly handle, a handle that won't tighten, or misalignment after service

• Disconnect power; turn off the water supply
• Protect the door/drawer finish and support the handle during removal
• Remove the handle per your model's instructions and take out the damaged anchor
• Install the new anchor using the existing mounting location/hardware, seat the handle fully, then tighten set screws evenly without overtightening