Parts for Lg LSD4913ST/00: Introduction Parts

Replace a gas range burner when flames are uneven, won't ignite, or produce yellow flames. Direct swap installation takes 10-15 minutes with basic tools.

Burner not heating or heating unevenly? This surface element restores full heat output on your range. Straightforward DIY fix in under an hour.

A Tap-Tite binding-head screw used to fasten appliance panels and components where a self-tapping metal thread is required. Replaces missing or damaged fasteners to restore secure assembly and reduce vibration or rattling. What it does:

• Creates its own mating thread in thin sheet metal for a secure hold without a nut.
• Holds panels, brackets, and trim in place to prevent looseness or movement.
• Commonly used where stripped, missing, or broken screws cause rattling, misalignment, or parts that won't stay attached.
• Compatible with standard screwdrivers or nut drivers sized to the binding-head.

• Disconnect power and unplug the appliance before working on it.
• Use the correct driver bit to avoid cam-out or head damage.
• Start straight and apply steady pressure; avoid overtightening to prevent stripping the formed threads.
• If the original hole is badly damaged, assess for repair or use of a larger fastener as needed.

Insulator for electric and gas ranges. Installs between internal components to provide heat or electrical protection. Replace if cracked or missing.

This is a replacement screw used to secure appliance components and panels. It restores proper fastening where a stripped, missing, or damaged screw causes loose parts or rattling. What it does:

• Fastens panels, trim, or internal components to maintain structural fit
• Helps stop vibration-related noise from loose assemblies
• Replaces missing or corroded screws that prevent proper closures
• Restores secure mounting after repairs or disassembly

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug—do not over-torque to prevent thread damage
• Keep small parts away from children and pets
• Disconnect power or water before accessing internal parts

The Common Nut is an OEM part for LG ranges. It secures the fan blade to the motor shaft. This nut maintains the fan's stability and preventing it from becoming dislodged during use.

Causes of a bad common nut can include loosening over time due to vibration, improper installation, or damage from impact or mishandling.

Symptoms of a bad common nut include:

• Excessive noise or vibration from the fan assembly
• The fan blade becoming loose or detached, causing poor air circulation
• Potential risk of the fan blade becoming a projectile if completely detached

This OEM LG part is also compatible with some Kenmore models.a

Replacement screw for securing panels, brackets, and internal components. Restores tight fit and proper alignment when original hardware is stripped or missing.

A factory screw for securing specified components in your appliance. Replaces a missing or damaged fastener to restore a tight, reliable hold and help reduce vibration, rattling, and misalignment.

• Secures brackets, covers, or internal assemblies where this exact screw is specified by the manufacturer
• Useful when the original screw is missing, stripped, or corroded
• Helps eliminate looseness, vibration, and rattling noises
• Matches the original fastener for proper fit and thread engagement

• Disconnect power (and shut off water supply if applicable) before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace any damaged clips or inserts to ensure a secure repair

Secures panels, brackets, and internal components in your range. Replace this screw if the original is missing, stripped, or rusted for proper fit.

This customized screw secures appliance components where a standard fastener won't fit, helping keep panels, brackets and small assemblies stable. It's a direct-fit replacement when the original specialized screw is missing or damaged. What it does:

• Fastens and holds appliance panels, brackets or small parts in place
• Prevents rattling, loose trim or misaligned components caused by a missing or stripped screw
• Matches the OEM fit and thread pattern for proper engagement and alignment
• Used in locations that require a non-standard or customized fastener

• Disconnect power and water before servicing the appliance
• Use the correct screwdriver or driver bit to avoid stripping the head
• Tighten securely but do not overtighten; overtightening can strip threads or crack parts
• Keep removed hardware organized so you can reinstall in the original location

This hardware washer helps distribute fastener load and maintain proper spacing in your LG appliance. Replacing a missing or worn washer restores secure mounting and alignment, reducing vibration and rattling from loose assemblies.

• Distributes the load of a screw or bolt and protects mating surfaces to maintain alignment
• Helps keep components secure and at the correct spacing
• A damaged or missing washer can lead to loosening, vibration, or rattling during operation
• Ensures correct hardware stack-up during reassembly after service

• Disconnect power and shut off water or gas before servicing
• Note the order and orientation of any washers/spacers; take a reference photo
• Use the correct driver or wrench and tighten snugly—do not overtighten
• Replace companion hardware if corroded, stripped, or damaged

The Common Nut is an OEM part for LG ranges. It secures the fan blade to the motor shaft. This nut maintains the fan's stability and preventing it from becoming dislodged during use.

Causes of a bad common nut can include loosening over time due to vibration, improper installation, or damage from impact or mishandling.

Symptoms of a bad common nut include:

• Excessive noise or vibration from the fan assembly
• The fan blade becoming loose or detached, causing poor air circulation
• Potential risk of the fan blade becoming a projectile if completely detached

This OEM LG part is also compatible with some Kenmore models.a

This is a replacement customized screw designed to secure appliance panels and components. It restores proper fit and fastening where the original screw is lost or worn, helping maintain safe, stable operation. What it does

• Replaces missing or damaged mounting screw used on appliance panels and internal components
• Restores secure fastening to reduce vibration and rattling during operation
• Matches the original OEM fit and thread form for correct engagement when verified for your model
• Helps prevent loose parts that can cause noise or interfere with moving components

• Disconnect power and water before servicing the appliance
• Verify screw size, thread direction, and length match the original before installation
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten securely but avoid overtightening to prevent stripping or damaging mating threads

Replaces a cracked, missing, or damaged control knob on your electric range. Restores secure temperature and cycle selection on the control panel.

Replace a cracked, stripped, or missing control knob to restore precise temperature and burner control. Simple snap-on installation takes minutes.

The PCB Assembly, Sidekey is an OEM replacement part for LG  ranges. This printed circuit board assembly is responsible for controlling the functions of the control panel on the side of the range. It communicates with all electronic components to operate the cooktop burners, oven lights and fans, and programming features.   

Causes of a bad PCB assembly can include corrosion of printed circuits over time due to heat exposure, moisture damage, or component failure.

Symptoms of a bad PCB assembly include: 

• Cooktop burners not working properly or unresponsive to control panel commands
• Inability to turn on oven lights or fans
• Programming features like timers or temperatures not functioning correctly
• Blank or unresponsive control panel displays

This OEM LG part is also compatible with Sears/Kenmore ranges. Replace yours today with this genuine electronic control board and upgrade the functionality of your electric range oven.

Range not heating or control panel unresponsive? This control board assembly restores oven functions. Moderate difficulty repair requiring basic tools.

Fix a range that won't heat, cycle on, or respond to buttons. This control board assembly interprets inputs and restores reliable oven operation.

Fix an unresponsive oven control knob or broken control dial. This encoder board detects knob position and sends signals to adjust temperature settings.

Replacement screw for electric and gas ranges. Secures panels, brackets, and internal assemblies. Restores tight fit when original is missing or stripped.

Factory-style screw for securing panels, brackets, and assemblies on gas ranges and cooktops. Replace if missing, stripped, or damaged during repairs.

Replace a faulty gas range burner nozzle if flames are uneven, yellow, or won't ignite properly. This part meters fuel flow to each burner for balanced heating.

Fix range display not working, oven not heating, or control panel errors with this power control board assembly. Moderate DIY repair for ranges.

Fix a range that won't heat, displays error codes, or has unresponsive controls. This main control board manages power distribution and system logic.

Pipe assembly for gas ranges. Connects gas supply lines within your range. Replace if cracked, corroded, damaged, or leaking to restore safe operation.

The Pipe Assembly is an OEM part for LG ranges and cooktops. This manifold is responsible for housing the gas valves and safely distributing gas to each burner. It works to allow control and adjustment of burner flames.

Over time, gas valves and other internal parts can become worn or damaged due to regular use and exposure to heat. Causes of a bad Pipe Assembly can include faulty gas valves that do not properly regulate gas flow, damage to internal tubing or gas lines, or worn seals and gaskets.

Symptoms of a bad Pipe Assembly include:

• Inconsistent or irregular burner flame sizes
• Difficulty adjusting burner flames
• Flames that become too high or too low and unstable
• Front burners that do not ignite or light unevenly
• Gas smells coming from the range

This OEM LG part is also compatible with some Kenmore models.

Adjustable leveling foot assembly for ranges. Installs on the bottom of your appliance to provide stability. Replace if broken, cracked, or missing.

Replace your range's outer door frame to restore door structure, improve seal integrity, and fix cracked or bent trim. Confirm fit with your model number.

Replacement window glass for range oven doors. Restores clear viewing area when original glass is cracked, chipped, cloudy, or shattered. Installs inside door.

This replacement door handle restores a secure, easy-grip opening to your refrigerator door. It matches the OEM shape and mounting points so the door operates smoothly and looks factory-fresh. What it does:

• Replaces a cracked, loose, or broken refrigerator door handle so the door is easier and safer to open.
• Restores proper grip and leverage for normal daily use.
• Reinstalls to existing factory mounting points to maintain door alignment and appearance.
• Helps prevent further cabinet or door damage caused by using a compromised handle.

• One refrigerator door handle

• Requires removing the old handle and securing the replacement to the same factory screw bosses; use the original screws unless new hardware is explicitly listed.
• Handle hardware may be hidden under trim—check for set screws or clips before prying.
• Support the door while working to avoid strain on hinges; two-person assistance recommended for larger doors.
• Disconnect power only if required for surrounding panels—this is an exterior handle replacement and typically does not require electrical disconnection.

Replacement window glass for range oven doors. Restores clear viewing area when original glass is cracked, chipped, cloudy, or shattered. Installs inside door.

Inner door cover panel for electric and gas ranges. Replaces damaged, cracked, or missing inner door cosmetic panels. Installs on the interior door assembly.

Bracket that anchors the handle to your range oven door. Replace if cracked, stripped, or broken to restore secure handle attachment and alignment.

Color: Stainless w/black glass

Supports your range door and provides smooth opening and closing. Replace if the door sags, misaligns, or won't stay open. Confirm fit with your model.

Front panel assembly for your range. Replaces a cracked, damaged, or discolored control panel face. Installs on the front of the appliance.

Fix unresponsive controls or erratic operation with this range main power control board. Restores electronic functions and cycle reliability. Moderate difficulty repair.

The Oven Selector Knob Supporter is an OEM replacement part for LG ovens. It is a crucial component that provides structural support and ensures proper functioning of the oven selector knob mechanism.

Symptoms of a bad oven selector knob supporter:

• Loose or wobbly oven selector knob
• Difficulty in turning or selecting oven functions
• Knob becoming detached or falling off
• Misalignment or binding of the knob mechanism

Causes of a faulty oven selector knob supporter can include physical damage, wear and tear over time, or manufacturing defects that compromise its structural integrity or alignment.

This OEM LG part is also compatible with Sears/Kenmore ovens.

Wire harness for gas ranges. Connects electrical components inside your range. Replace if wires are frayed, damaged, or connections are loose or broken.

Fixes intermittent power or control issues caused by damaged wiring. This harness restores electrical connections between range components for reliable operation.

Range controls not responding or features intermittent? This wiring harness restores power and signal connections between components for reliable operation.

This single wiring harness routes power and signals between control components to restore reliable electrical connections inside the appliance. Replacing a damaged harness helps eliminate intermittent operation and faulty control responses. What it does:

• Carries power and control signals between modules and components
• Re-establishes lost or intermittent electrical connections
• Stops failures caused by broken, burned, or corroded wiring/terminals
• Helps resolve symptoms such as no power to circuits, erratic controls, or components not responding

• Disconnect all power before starting any repair to avoid shock or damage
• Match connector shapes and pin count before fastening; do not force connections
• Route harness away from sharp edges, heat sources, and moving parts to prevent future damage
• If terminals or connectors are damaged, replace the entire harness rather than attempting field splices

If your range control panel is loose or cooking functions are erratic, the PCB supporter may be cracked. This mounting bracket secures the circuit board.

Support bracket that secures the control board assembly inside your range. Replace if the bracket is cracked, bent, or missing to properly mount the PCB.

Fix an oven door that won't stay open or slams shut with this range door spring. Simple DIY repair requiring only a Phillips screwdriver, 30 minutes.

Replace your range's oven door glass window if cracked, broken, or missing. This inner glass installs between the door panels for safe viewing.

A circular lug designed to join a stripped wire to a threaded terminal for a secure electrical connection. Helps restore reliable contact at terminals and reduces the chance of intermittent power or arcing at connection points. What it does:

• Provides a strong mechanical and electrical connection between a wire and a screw or bolt terminal.
• Helps prevent loose connections that can cause intermittent operation, sparking, or overheating.
• Commonly used where a ring-style termination is required for safe, stable wiring.
• Works with properly sized wire and fasteners to maintain consistent conductivity.

• Always disconnect power to the appliance before inspecting or replacing electrical parts.
• Use the correct lug size and gauge for the wire and terminal; crimp or solder per manufacturer recommendations.
• Tighten terminal hardware to the appliance manufacturer's specified torque; avoid over-tightening which can damage the lug or terminal.
• If wiring insulation or the terminal is damaged or corroded, replace the affected components rather than reusing them.

Rear cover panel for gas ranges. Mounts on the back of the range to conceal internal components. Replace if cracked, damaged, or missing.

This vent grille is the external trim piece that covers and protects the appliance exhaust opening, restoring proper airflow and finished appearance. It replaces damaged or cracked vent trim so air can vent safely and the appliance looks complete. What it does:

• Covers the appliance exhaust opening while directing airflow out of the cabinet or housing
• Helps prevent debris from entering the vent area and protects internal components
• Commonly replaced when cracked, broken, warped, or cosmetically damaged
• Can reduce air leaks around the exhaust opening when properly seated

• One vent grille

• Turn off and unplug the appliance or disconnect power before servicing
• Removal/installation typically requires removing a few fasteners or clips—handle trim pieces gently to avoid cracking
• Align grille tabs and secure with original screws or clips; do not overtighten

Replace a cracked, warped, or worn top plate on your gas range. This metal surface panel installs on the cooktop frame to restore appearance.

Idle packing bushing for electric and gas ranges. Replaces worn, cracked, or missing bushings. Ensures proper fit and cushioning for range components.

This rear cover is the replacement cabinet panel that protects internal components and restores the original enclosure for proper airflow and safety. It helps keep wiring and electronics shielded from damage and dust. What it does:

• Replaces a cracked, warped, or missing rear cabinet panel
• Protects internal wiring, control boards, and components from debris
• Restores proper enclosure to help maintain intended airflow and clearance
• Reduces risk of accidental contact with live parts during operation

• Disconnect power before starting any repair to avoid electric shock
• Handle edges carefully; use gloves to protect hands from sharp sheet-metal edges
• Reinstall using existing screws and mounting points; verify secure fit and clearance

Oven rack for electric and gas ranges. Provides stable surface for cookware during cooking. Replace if bent, warped, cracked, or missing.

Fix uneven flames or burner not lighting with this gas range burner tube. Direct replacement for standard slide-in and freestanding models.

Surface burner grate for gas ranges and cooktops. Sits atop burner to support cookware during cooking. Replace if warped, cracked, broken, or chipped.

The Surface Burner Grate is an OEM part specifically designed for LG ranges. It sits above the gas burners on the cooktop providing a durable, heat-resistant surface for cookware. 

Causes of failure typically include warping, cracking, or breaking of grate bars from prolonged heat exposure over the life of the range. Material strength degradation is normal with heavy use.

Symptoms of faulty grates include:

• Uneven or inefficient heat transfer to pans 
• Risk of cookware bottom damage from direct flame contact
• Potential gas leaks or fire hazards without grate coverage
• Loss of a functional, attractive cooktop appearance

This OEM part also fits select Sears/Kenmore ranges.

The Grille Assembly is an OEM part for LG cooking ranges and range tops. It provides an additional flat-top cooking surface between the standard burner elements. The grille assembly itself is constructed of heavy-duty materials designed to withstand high heat levels while cooking.

Causes can be wear over time under heavy usage, accidental damage from cookware or cleaning, or failure of the heating elements underneath the plate.

Symptoms of a bad griddle plate include:

• Uneven or slow heating of the surface
• Warping or bending of the plate
• Scratches, cracks, or other surface damage
• Loose or missing mounting hardware

This LG part is also compatible with some Kenmore models.

Gas burner orifice nozzle for ranges and cooktops. Installs inside the burner box to meter gas flow. Replace if damaged, missing, or converting fuel type.

Fix weak flames or burners that won't light properly with this gas burner nozzle. Controls gas flow for proper flame size. Simple install with basic tools.

Gas burner orifice nozzle for ranges and cooktops. Installs inside the burner box to meter gas flow. Replace if damaged, missing, or converting fuel type.

Fix weak flames or burners that won't light properly with this gas range burner nozzle. Controls gas flow for optimal flame performance. DIY install.

Fixes burners that won't light or ignite properly on your gas range. This gas valve assembly controls gas flow to surface burners. Moderate DIY repair.

Fix burners or oven not lighting with this gas valve assembly. Controls gas flow to restore safe ignition and consistent heating in your range.

Gas range won't ignite or heat properly? This valve assembly controls gas flow to your oven and burners. Restores ignition and safe operation.

Controls gas flow to your range burner. Replace this valve assembly when the original is faulty, leaking, or damaged to restore safe gas regulation.

Replace a cracked, discolored, or missing burner cap that's causing uneven flames or allowing spills into the burner assembly. Fits over the burner head.

If your gas range has uneven flames, yellow or orange flames, or won't light properly, a damaged burner cap is often the cause. This part restores safe, even heat distribution.

Fixes uneven flames and improves heat distribution. This burner cap covers the burner head to direct flame properly and protect against debris buildup.

Uneven flame or poor heating? This gas range burner cap directs flames evenly across cookware and contains sparks. Simple snap-on installation.

Fix intermittent power issues or control failures with this range main wiring harness. Connects electrical components for proper signal communication.

Cable assembly for gas ranges. Replaces worn, damaged, or broken cable connections inside your range. Essential structural component for proper operation.

Fix control issues or power failures with this gas range cable assembly. Restores reliable operation when wiring is damaged, burned, or has loose connections.

Fixes unresponsive controls or features not working on your gas range. This cable assembly restores power and signal connections between components.

Fix burners that won't light or controls that don't respond with this range wire harness. Restores electrical connections between components. Moderate DIY.

Bending pipe for gas ranges. Connects gas supply lines between burner valves and manifold. Replace if cracked, bent, corroded, or leaking at connections.

Bending pipe for gas ranges. Connects gas supply lines within the range assembly. Replace if bent, cracked, or damaged to restore proper fit and alignment.

Fix unresponsive control panel buttons with this tactile switch replacement. Restores reliable button response. Simple DIY repair, typically under 5 minutes.

Microwave won't turn on or has no power? A failed thermostat often causes complete power loss. Moderate DIY repair requires disassembly to access.

Replace your range's wire harness if the existing wiring is damaged, frayed, or showing signs of wear. Connects electrical components inside your range.

The Magnetron Thermostat is an OEM part for LG microwaves and built-in ranges. Its primary function is to monitor the temperature and ensure that it remains within a safe operating range. If the temperature exceeds the preset limit, the thermostat will interrupt the power supply to the magnetron, preventing overheating and potential damage.

Causes of a faulty magnetron thermostat can include electrical malfunctions, component failures, or physical damage. These factors can result in issues such as erratic heating, microwave not heating properly, or the appliance shutting off unexpectedly.

Symptoms of a bad magnetron thermostat may include:

• Microwave not heating food evenly or at all
• Inconsistent or weak heating performance
• Microwave shutting off or displaying error codes related to temperature issues

This OEM LG part can also be used on Kenmore/Sears appliances. 

If your oven won't reach the right temperature or shows an F9 error, the temperature sensor may be faulty. Simple DIY repair in under 45 minutes.

Replace a damaged or corroded wire harness in your range. This single-connection harness restores proper electrical connections when original wiring is frayed, melted, or broken.

Fix uneven cooking or baking in your range. This convection fan motor circulates hot air for consistent heat distribution. Moderate DIY repair.

Secures the control panel to your range cabinet. Replace if the bracket is cracked, bent, stripped, or hardware no longer holds the console firmly in place.

Wire harness for electric and gas ranges. Connects electrical components inside your range. Replace if wires are frayed, damaged, or connections are loose.

Motor loose or vibrating excessively? This motor bracket secures the motor to the chassis, reducing vibration and maintaining alignment for quieter operation.

Fix loose or misaligned range components with this retaining ring. Secures parts in place to prevent excess movement and wear. Simple installation.

Fixes uneven baking and longer cooking times in your range. This convection fan blade restores proper air circulation for consistent oven temperatures.

This Fan Blade is an OEM part for LG microwaves. It is a critical component designed to circulate air within the microwave, aiding in heat dissipation and ensuring even cooking. 

Fan blades in microwaves can suffer from wear, imbalance, or damage due to regular use or accumulation of debris. A malfunctioning fan blade can lead to inadequate ventilation, affecting the microwave's cooking efficiency and potentially causing overheating.

Symptoms of a bad fan blade include:

• Unusual noises during operation, such as rattling or buzzing, indicate a loose or damaged blade.
• The microwave overheating or shutting off prematurely.
• Inconsistent cooking or hot spots in food suggest poor air circulation.
• The fan not starting, or stopping unexpectedly during use.
• Visible signs of damage or wear on the blade.

This OEM LG part is also compatible with some Sears/Kenmore models.
 

Replace your damaged or broken range handle bar. This bar installs on the oven door, providing a secure grip for opening and closing. Order now.

Fix a humming or stalled range component with this AC synchronous motor assembly. Restores proper rotation when the motor fails to turn or makes noise.

Range heating element loose or misaligned? This heater mounting bracket secures your heating assembly to the cabinet for stable, reliable operation.

Replace your range's control panel if the original is cracked, damaged, or has faded graphics. This panel mounts to the front of your appliance housing.

Replace your burned-out or dim oven light bulb to restore interior visibility while cooking. Direct-fit incandescent lamp for safe food monitoring. Verify fit with your model number.

This hinge bracket secures the oven door hinge mechanism on your range. Replace if the bracket is cracked, broken, bent, or missing to restore door support.

Oven won't brown or crisp food on top? Replace the broil element. This upper heating component restores efficient broiling in electric ranges.

The range packing seal creates an airtight barrier around oven doors or other range components to maintain proper cooking temperatures and prevent heat loss. Positioned around door edges or component joints, it needs replacement if heat escapes, cooking becomes uneven, or the seal appears cracked or compressed.

Oven not heating or baking unevenly? This electric range heating element restores proper cooking temperature. Moderate DIY repair in 30-45 minutes.

Secures and supports your range oven door hinge for proper alignment and smooth operation. Replace if bracket is cracked, bent, or damaged to restore door fit.

Replacement support bracket for range control panels. Installs behind the control panel to provide structural support. Needed when original is broken or missing.

Range oven door gasket seals the oven cavity to retain heat and improve efficiency. Replace if torn, cracked, or no longer sealing properly. Confirm fit.

Fix uneven oven temperature or burner control issues with this range governor assembly. Regulates gas flow for consistent heating. Moderate DIY repair.

Base plate for electric and gas ranges. Provides structural support at the bottom of the appliance. Replace if cracked, broken, or missing. Easy install.

If your gas range burner won't ignite or heat unevenly, this surface burner assembly restores reliable flame and even cooking. Moderate DIY repair.

Secures and finishes your range door opening with proper structural support. Replace if cracked, warped, or damaged to restore door alignment and seal.

Outer front plate panel for ranges. Restores exterior appearance and provides finished surface for controls. Replaces damaged, dented, or scratched panels.

Replaces the outer control panel on your range. Restores appearance when the original is cracked, scratched, or worn. Covers and protects controls.

Rubber foot pad that supports and stabilizes your range on the floor. Replace if cracked, broken, worn, or missing to keep your appliance level.

Idle bracket for electric and gas ranges. Secures internal components in place. Replace if bracket is bent, cracked, broken, or missing during repair.

Replacement slider for range drawers and panels. Restores smooth movement when original is worn, cracked, or broken. Mounts to moving components for alignment.

Replace worn range drawer sliders to restore smooth, quiet operation and proper alignment. Prevents damage to surrounding trim. Confirm fit with your model.

Replacement oven rack support bracket for your range. Installs inside the oven cavity to hold racks in place. Replace if cracked, broken, or missing.

Mounting anchor for range door handles. Replaces worn, broken, or missing anchors to restore secure handle attachment and eliminate wobbling or loose fit.

The LP Conversion Kit is an OEM part for LG gas ranges, allowing safe conversion between natural gas and liquid propane fuel sources. It features necessary valve bodies and tubing to appropriately meter gas flow.  

Causes of failure involve worn or corroded tubing restricting gas volumes over time, stripped injector threads inhibiting secure connections, or damaged valves losing precise metering accuracy.

Symptoms of a bad LP conversion kit include:

• Improper flame levels unable to heat cooktop/oven  
• Gas smell signaling unsafe leaks at connections
• Incorrect fuel/air ratios affecting efficiency and safety
• Non-functioning burners from blocked or disconnected lines

Replace yours today with this genuine OEM LG kit. Certified components uphold performance standards across Whirlpool, Frigidaire, and Kenmore gas models as well by mitigating combustion risks. 

Accessory assembly for electric and gas ranges and wall ovens. Replaces damaged, broken, or missing accessory components. Restores proper fit and function.

Decorative trim piece that surrounds the rear of your range for a finished look. Replace if cracked, chipped, damaged, or missing. Enamel finish.