Jade Refrigerator Parts

This is a refrigerator drip pan kit. It is located on the bottom of the appliance and is used to help catch condensation from the appliance. Any moisture that is made while the refrigerator goes through its operation cycles will collect in the pan to prevent a mess. If the drip pan has been damaged, the most common symptom is water dripping on the floor. Checking for a clog should be done. If the actual part is damaged, it will need to be replaced.Before replacing the drip pan kit, unplug the power cord on the appliance and pull the refrigerator from the wall. Use a nut driver to release the water inlet line coupler before taking off the access panel. Reach in and bend the pan retaining tab, open the doors of the appliance, and take off the water filter cover. Remove the toe plate to access and replace the drip pan.This is a genuine OEM drip pan kit that can be used as a replacement for Dacor, Jenn Air, Hardwick, and Maytag refrigerators. It is sold as an individual component and is provided directly from the manufacturer.

This hose clamp secures a rubber or plastic hose to its fitting on your appliance, maintaining a tight, leak-resistant seal under vibration and pressure. Replace when the old clamp is rusted, bent, or no longer holds tension. What it does:

• Clamps around a hose to grip the fitting and seal the joint
• Helps prevent drips, leaks, and hose blow-off at the connection
• Restores secure clamping force when the original is worn or damaged
• Common symptoms: water at the connection, hose slipping off, visible corrosion or distortion

• 1 hose clamp

• Disconnect power and shut off the water supply before servicing
• Slide clamp onto hose, seat hose fully on the fitting, then position clamp just behind the bead/raised lip
• Tighten or compress evenly with the appropriate tool; avoid overtightening that could damage the hose
• After reassembly, run a short test and inspect for leaks

This genuine replacement screw secures appliance panels and trim so covers, consoles, and components stay firmly in place for safe, quiet operation. It replaces worn or missing fasteners to restore proper fit and reduce vibration and rattling. What it does:

• Secures control panels, trim pieces, or access panels to the appliance frame
• Keeps panels aligned to prevent gaps and light leaks
• Reduces vibration-related noise from loose panels or components
• Helps maintain safe operation by keeping covers and guards properly attached

• The replacement screw shown/listed

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct screwdriver or driver bit to avoid stripping the head
• Start the screw by hand to ensure proper thread engagement, then tighten securely but do not overtighten

This product is a Whirlpool refrigerator drip pan for the evaporator. The drip pan is in place to catch water created from defrosting or condensation created by the evaporator. A damaged or clogged pan will lead to water leaking underneath the appliance. Substantial leaks from the refrigerator need to be inspected. Typically the two leading causes would be a worn-out seal from the door causing ice to melt or a clogged or damaged drip pan. Carefully examine the drip pan to ensure it's not just a clog, which is easily fixable. Any cracks or more significant damage means a replacement should be ordered.Access the drip pan by removing the bottom vent of the refrigerator. The drip pan is connected to the evaporator. Unplug the refrigerator to ensure safety before making any repairs. Carefully unscrew the nut that fastens the connecting line between the evaporator and the drip pan with a wrench. Remove the old drip pan and insert the new product. Make sure the nut is tight enough to make a good connection between the evaporator and the new component.This product is compatible with Whirlpool, Admiral, Magic Chef, Jenn-Air, and KitchenAid appliances. This is a genuine OEM product sourced directly from the original manufacturer.

This is a flat plain washer used to distribute load and space hardware on appliance assemblies. It helps keep bolts and screws seated and reduces wear on mating surfaces for more secure fastener connections. What it does:

• Provides a flat bearing surface to spread clamp load and protect parts from fastener damage
• Maintains proper spacing and alignment for mounted components
• Helps prevent fastener loosening from vibration when used with the correct bolt or screw
• Commonly used on chassis, suspension, and bracket connections

• One plain flat washer

• Disconnect power and water supply before servicing the appliance
• Replace only with the same washer size and thickness as the original for proper fit
• Tighten fasteners to secure but avoid over-torquing which can deform the washer

This grommet seals the appliance's fill tube to keep the water path watertight and properly routed. It helps prevent leaks where the fill tube passes through the cabinet or dispenser area. What it does:

• Seals the fill tube connection to stop drips and slow leaks
• Keeps water flowing along the intended path to the dispenser or valve
• Cushions the tube where it passes through panels to reduce wear
• Helps prevent water damage and maintain normal fill operation

• Turn off power and shut off the water supply before servicing
• Access the fill tube area per your model's service instructions; grommet typically presses into an opening and the tube pushes through
• Inspect the tube and surrounding area for damage; replace if cracked or excessively worn
• After installation, restore water and power, then check for leaks during a short fill cycle

This 8-32 x .340 machine screw secures small appliance panels and components for a reliable fit. It's a simple replacement fastener when original screws are missing, stripped, or worn. What it does:

• Fastens panels, brackets, and internal components where 8-32 threads are required
• Provides a short, firm hold for thin materials and assemblies
• Useful when original mounting screws are lost or damaged
• Matches OEM thread size and length for correct fit in designed screw bosses

• One 8-32 x .340 machine screw

• Use the correct screwdriver or nut driver to avoid stripping the head
• Do not overtighten; snug to secure without deforming plastic or stripping threads
• Confirm screw length and thread size match the original before installation
• Disconnect power and follow appliance safety precautions when accessing internal parts