Jenn-Air Range / Cooktop / Oven Latch, Catch, Lock Parts

This door strike is the catch the latch engages to hold the oven door closed. It restores a firm, aligned close so heat stays in and the appliance can detect a fully shut door for normal operation.

• Aligns with the latch to keep the door closed and sealed properly
• Provides the catch point required for latch/lock engagement
• Wear, bending, or breakage can cause a loose door, heat escaping, or an oven light that won't turn off
• Prevents self-clean or other cycles that require a fully closed/locked door from starting

• Disconnect power at the breaker; if gas, shut off the gas supply. Allow the appliance to cool completely
• Typically mounts to the door or cabinet frame with screws; transfer and reuse existing hardware
• Position and tighten evenly so the latch engages smoothly; minor alignment adjustments may be needed
• After installation, verify the door closes fully, seals well, and the light turns off

This door latch keeps the door securely closed and engages the door switch/interlock so the appliance operates as designed. Replacing a worn or broken latch helps resolve door-related errors and restores reliable, safe operation.

• Secures the door against the strike for proper closure and alignment
• Actuates the door switch/interlock so controls recognize a closed door
• Helps prevent operation when the door is open or not fully latched
• Common symptoms: door won't latch or stay closed; unit won't start or shows a "door/open-close" message; broken or loose latch hook

• Disconnect power before servicing; use proper PPE and beware of sharp edges
• Access the latch through the door panel/trim as applicable; use non-marring tools to avoid damage
• Transfer any reusable clips/springs from the old latch to the new part
• After installation, verify smooth door closure and that the control detects the door as closed

This lid switch actuator engages the washer's safety switch when the lid is closed so cycles can start and spin as designed. Replace a broken or missing actuator to restore proper lid switch engagement and reliable operation.

• Engages the lid switch when the lid is closed to enable agitation and spin
• A worn, cracked, or missing actuator can cause the washer not to start or to stop before spin
• Intermittent operation that changes when pressing on the lid often indicates misalignment
• Lack of an audible "click" from the lid switch can point to a faulty actuator or alignment

• Disconnect power before servicing; do not work on a live appliance
• Access the lid/switch area per your model's service procedure
• Remove the damaged actuator and install the new part, securing as designed
• Before reassembly, close the lid to ensure the switch clicks and engages properly

This door latch secures the appliance door and signals the control that it's safely closed. Replacing a worn or broken latch restores reliable door closure and proper cycle operation. What it does:

• Holds the door closed and aligned during use
• Engages the door strike to complete the door/lock switch circuit
• Resolve issues such as: door won't latch or pops open; cycles won't start; intermittent "door open" messages; needing to press/hold the door to run

• One door latch

• Disconnect power before servicing
• Access is typically from the door/front panel; note screw locations and latch orientation
• Transfer any mounting hardware from the original latch if needed
• After installation, verify smooth latch engagement with the strike and run a test cycle

This door latch assembly secures and electrically locks the washer door so cycles can start and run safely. It replaces a worn or failed latch to restore proper door locking and cycle operation. What it does:

• Physically secures and aligns the washer door so it closes properly.
• Activates the door-lock switch so the machine can start and run.
• Helps prevent the door from opening mid-cycle, reducing leaks and interruptions.
• Commonly used when the washer won't start, shows a door-lock error, or the door won't stay closed.

• One complete door latch assembly.

• Disconnect power before starting any repair to avoid shock or injury.
• Remove the washer door boot or front panel to access the latch.
• Check wiring harness connections and connector orientation before reconnecting.
• After installation, run a short diagnostic or test cycle to ensure the latch locks and releases correctly.

This part is a replacement door latch assembly that is intended for use with wall ovens.The door latch assembly makes sure that the oven door locks properly. This is an essential safety component, and the user may notice the appliance doesn't work or certain cycles, such as the self-cleaning cycle, will not start should the latch be faulty. Basic household tools are needed to install this part. Make sure the oven is powered off, unplugged, and cooled down before beginning the repair process.This part is compatible with several different wall oven models that have been manufactured by Whirlpool, Maytag, Kitchenaid, Magic Chef, Amana, Admiral, and some other brands. It is a genuine OEM part from Whirlpool made of high-quality, durable materials. This part is sold individually.