Jenn-Air Range / Cooktop / Oven Motor

The Fan Blower is an OEM replacement part for Whirlpool ranges. This component is crucial for circulating air within the range to ensure even heating and proper ventilation during cooking.

The fan blower can fail due to wear and tear from regular use, buildup of grease and debris, or electrical issues. Overheating or physical damage can also cause the blower to malfunction.

Symptoms of a bad fan blower include:

• Unusual noises or rattling during operation
• Inadequate ventilation or uneven cooking
• The fan not running or starting intermittently
• Overheating of the range

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Turntable Motor is an OEM part for Whirlpool microwave ovens. It is responsible for rotating the turntable or carousel tray inside the microwave, ensuring even heating and cooking of food.

Causes of a bad Turntable Motor can include wear and tear over time, lack of proper lubrication, or issues with the motor's bearings or electrical connections.

Symptoms of a bad Turntable Motor may include:

• The turntable not rotating or spinning erratically
• Loud grinding or squeaking noises during operation
• Potential uneven heating or hot/cold spots in food

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This tangential cooling fan moves a wide stream of air across the oven cavity and control area to remove excess heat. Replacing a weak or noisy blower restores proper cooling to help protect control electronics and surrounding surfaces.

• Circulates cooling air to dissipate heat from the oven and control panel
• Operates during and after bake/broil/self-clean to keep temperatures in check
• Helps prevent over-temperature shutdowns and protects internal components
• Common symptoms: fan won't run, runs loudly or vibrates, weak airflow; control area feels too hot; oven may shut off early or display a cooling fan/over-temp error

• Disconnect power at the breaker and allow the appliance to cool before servicing
• Access location varies by model (often behind the control/top trim or rear cover)
• Note wire positions and mounting orientation; transfer any brackets as needed and reuse original hardware
• Watch for sharp metal edges; verify smooth, quiet fan operation before reassembly

This fan motor powers the cooling fan that moves air through your unit. Replacing a worn or noisy motor restores proper airflow to help maintain stable temperatures and reliable performance. What it does:

• Drives the fan blade to circulate air for cooling and temperature control
• Helps prevent component overheating caused by weak or stalled airflow
• Fixes: fan not running or starting intermittently
• Fixes: loud humming, grinding, or rattling from the fan area
• Fixes: longer run times or warm spots due to poor airflow

• Includes: 1 fan motor

• Disconnect power before servicing; allow moving parts to stop
• Note wire positions and motor orientation; take a photo for reference
• Transfer the existing fan blade and mounting hardware as needed
• After install, ensure the fan spins freely and no wiring contacts moving parts before restoring power

The Convection Fan is an OEM part for Whirlpool wall ovens and ranges. It circulates hot air inside the oven cavity, facilitating even heat distribution during the cooking and baking cycles. The convection fan enhances cooking performance through fast, forced air movement.

Causes of a bad convection fan include a failed motor, worn-out blades, or blockages that disrupt airflow.  

Symptoms of a bad convection fan include:

• Incomplete or uneven cooking even at higher temperatures
• Longer than normal cook times 
• Loud buzzing or grinding noises from the fan motor area

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Specs: 3/8 inch diameter shaft with a counter clockwise rotation. This fan motor kit is used on the Jenn-Air downdraft blowers. Includes the foam seal. For the foam seal only order 715957K.

The Motor-Fan is an OEM component specifically designed for Whirlpool kitchen ranges. Located within the back wall of the oven cavity, the motor fan works to circulate air and remove excess moisture and smoke during the cooking process. Proper motor-fan functioning helps ensure efficient oven ventilation and performance.

Symptoms of a bad motor fan include:

• Excessive smoke or moisture left in the oven after cooking  
• Oven taking longer to preheat and cook due to poor air circulation
• Loud buzzing or grinding noises emanating from the fan

Causes of failure are normally wear and tear of motor windings or fan blade bearings from years of continuous use. Overheating can potentially reduce lifespan as well. 

This OEM Whirlpool part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Blower Motor is an OEM part for Whirlpool ranges. It is an electronic component located underneath the range that is responsible for removing heat, smoke, and odors from the kitchen. The down draft blower motor operates an exhaust system that draws air through a vent behind the cooking surface and vents it outside.

Causes of a bad down draft blower motor can include normal wear and tear over time, exposure to grease or debris which can cause clogs or mechanical issues.

Symptoms of a faulty down draft blower motor include:

• Inadequate ventilation of heat, smoke or odors from cooking
• Slow or delayed venting of the cooking area
• Loud buzzing or grinding noises coming from underneath the range
• Failure of the venting system to turn on

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This blower motor moves air through the dryer to help vent heat and moisture so clothes dry efficiently. Replaces a worn or failed blower motor to restore proper airflow and drying performance. What it does:

• Spins the blower wheel to force air through the drum and exhaust vent
• Restores normal airflow when the dryer has little or no air movement
• Helps stop rattling, squealing, or grinding noises caused by a failing motor
• Helps reduce long dry times and overheating caused by restricted or weak airflow

• One blower motor

• Disconnect power to the appliance before starting any repairs
• Installation typically requires removing the dryer front or rear panel and accessing the blower housing
• Inspect the blower wheel and housing for lint or damage while replacing the motor

The convection fan is an OEM component for Whirlpool ranges. It functions as the convection fan system, circulating hot air within the oven cavity to provide efficient all-around heating. 

The convection fan is responsible for proper air circulation and temperature distribution during convection bake and roast cycles. It allows for fast, even cooking on multiple racks simultaneously.

Symptoms of a bad convection fan include:

• Inefficient or uneven baking/cooking results  
• Longer than normal cook times
• Overheating or hot spots within the oven
• Strange noises coming from the convection fan area

Causes can include a failed motor, worn fan blades, or blockages that disrupt airflow.

This Whirlpool OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore ranges.

This fan assembly circulates air through the appliance to support proper cooling and ventilation, restoring airflow and helping the unit maintain even temperatures and efficient operation. What it does:

• Moves air through the appliance to aid cooling, ventilation, or drying functions
• Helps prevent overheating by maintaining airflow across coils or heat sources
• Can reduce abnormal operating temperatures and airflow-related performance issues
• Restores proper fan operation when the original wheel or motor fails

• Disconnect power (and water, if applicable) before starting any repair
• Handle fan blades carefully to avoid damage or imbalance
• Inspect mounting hardware and wiring for wear; replace any damaged fasteners or connectors